Coopers 9450 Manuale utente
Paint Gun 9450 Instructions
Please read carefully before use and retain for future reference.
PARTS
1. Air cap 8. Sprayer bottle
2. Union nut 9. Hose
3. Sprayer 10. Shoulder strap
4. Trigger 11. On/Off Switch
5. Regulator screw 12. Funnel
6. Air flow tube 13. Air Pump
7. Suction tube
ASSEMBLY
• Attach the hose to the air pump, ensuring the nodule on the side of the
air pump housing is aligned with the recess in the hose fitting and twist
clockwise to secure.
• Push or twist the spray head onto the other end of the hose, ensuring it is
fitted securely.
• Attach the shoulder strap to either end of the paint gun, ensuring the
clips are securely fastened.
BEFORE USE
• Check all parts for damage before first use.
OPERATION
Preparing Materials
• The paint gun can be used to spray paint, lacquer or varnish.
• First measure the viscosity of the paint by dipping the funnel into the
paint until it is full of paint and timing how long it takes to drain out of
the funnel, see recommended viscosity table below:
Substance Funnel Drain time
Water-based paint, emulsion 25-50 seconds
Enamel paint, water-based or solvent-based
coloured lacquer 45-50 seconds
Primers 45-50 seconds
Varnish, wood coating, oil, disinfectants,
colouring agent Do not dilute
N te: The above table should be used as an approximate guide only. Always
follow the manufacturers’ instructions supplied with the substance.
• The paint gun can be used with substances with a funnel drain time of
25-50 seconds. Some paints may require diluting slightly until they reach
this viscosity.
• Initially dilute the paint with a thinner by 10% and stir well to mix.
• If the diluted paint still does not have the required viscosity, dilute by a further
5% and repeat until the desired viscosity is reached.
Spraying
• Depending on the angle at which
you are spraying, and whether the
surface is horizontal or vertical,
adjust the suction tube to the
desired position to ensure it is
pointing towards the section of
the container that is lowest
during use. See fig. 2
• Fill the container with paint.
• Ensure that all surfaces that are
not to be sprayed, e.g. screws,
screw threads, skirting boards,
wall sockets, etc. are covered.
• Ensure the surface to be sprayed
is completely clean and even
before spraying. Pre-treat the
surface before spraying if necessary.
• Always test on a piece of cardboard or an inconspicuous area
before proceeding.
• Always move the arm and not the wrist when spraying to ensure an even
distance is kept from the target area, typically between 5-15cm.
• Move the paint gun evenly to ensure an even coating.
Spray Settings
There are 3 spray settings, see fig. 3:
1. Vertical flat jet, used for horizontal
surfaces.
2. Horizontal flat jet, used for vertical
surfaces.
3. Circular jet, used for edges, corners and
hard to reach places.
To adjust the spray setting, turn the screw
anti-clockwise approximately two
rotations. Twist the air cap to the desired
setting and tighten the screw. See fig.4
To adjust the
volume of paint
sprayed, adjust the
regulator screw on
the trigger handle.
Turn anti-clockwise
to reduce the
volume sprayed
and clockwise to
increase. See fig.5
1.
2.
3.
4. 5.
13
Please read carefully before use and retain for future reference.
WARNING
• Ensure the work area is kept well lit, well ventilated and clean & tidy at
all times.
• Keep children and animals away from the work area.
• Do not allow children to play with the paint gun.
• Do not use near flammable or explosive liquids, gases or powders or
naked flames.
• Cover all surfaces that you do not wish to spray.
• Avoid contact with earthed surfaces.
• Check for damage before each use. Do not use if any part, including the
power cable, is damaged.
• Keep dry at all times. Do not get wet.
• When spraying outdoors, only use extension cables rated for outdoor use.
• Do not use under the influence of drugs, alcohol or prescribed medication
that could affect your ability to use the item safely.
• Always wear a protective mask, safety goggles, gloves, ear protection and
suitable clothing and footwear for decorating during use. Paint fumes can
be harmful.
• Maintain a stable, balance body position at all times during use.
• Do not point the air pump at people or animals.
• For domestic use only.
• Always switch off at the mains and unplug when not in use.
• Only use for intended use as stated in this manual.
• The appliance is not intended to be operated by means of an external timer
or separate remote control system.
• This appliance should not be used by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
• Do not use to spray flammable substances.
• Only spray the substances noted in the Preparing Materials section of
this manual.
• Do not use to spray flammable solvents with a flashpoint lower than 21°C.
• Never spray substances that you do not know the potential hazards of.
CLEANING
• Always switch off at the mains and unplug before cleaning.
• Unscrew the sprayer bottle and empty contents back into their original
container. Clean the sprayer bottle and the suction tube with a brush. Clean
the air vent.
• Pour water or solvent into the sprayer bottle, screw it back onto the paint
gun and plug into the mains. Turn the paint gun on and spray the solvent or
water into a container or onto a cloth.
• Turn off and unplug from the mains. Remove and empty the sprayer bottle.
• Pull out the suction tube and nozzle joint to clean.
• Remove the air flow
tube from the from
the paint gun and
unscrew the valve.
Remove the
membrane and
clean all parts
carefully before
replacing. See fig. 6
• Remove the air cap
& nozzle by
unscrewing the
union nut. Clean
the air cap, nozzle
and nozzle joint
with a brush and
solvent or water.
• Clean the outside
of the spray gun with a damp cloth and solvent if necessary.
• Do not use sharp or pointed metal objects to clean the paint gun.
TECHNICAL INFORMATION
Voltage 230-240V
Frequency 50Hz
Power Consumption 650W
Output 105W
Sprayer bottle capacity 800ml
Hose length 1.5m
Max. Viscosity 130DIN-secs
Motor Speed 32,000rpm
Weight (empty) 1.9kg
PACKAGING DISPOSAL:
• Dispose of all paper, cartons and plastic in accordance with your local recycling
regulations. At the end of the product’s lifespan please dispose of it at an
authorised household waste recycling centre.
EC DECLARATION OF CONFORMITY
We The Enterprise Department Ltd.
Of 11 Bridge Street, Bishop’s Stortford, Hertfordshire, UK. CM23 2 U
in accordance with the following Directive(s):
Electromagnetic Compatibility 2004/108/EC
EN 55014-1: 2006+A1
EN 55014-2: 1997+A1+A2
EN 61000-3-2: 2006+A1+A2
EN 61000-3-3: 2008
Low Voltage Directive 2006/95/EC
EN 60335-1:2002+A1+A2+A11+A12+A13+A14
EN 62233: 2008
EN 1953:1998+A1
Hereby declare that: Paint Gun
Model number: 9450 (Q1P-CX01-380)
I hereby declare that the equipment named above has been designed to comply
with the relevant sections of the above referenced specifications. The unit
complies with all applicable Essential Requirements of the Directives.
Mr. Stuart Fowler
Imports Director
December 2012
6.
Altri manuali Coopers Spruzzatore di vernice
