COP EA-PD01AF Manuale utente
0
PoE Splitter
User’s Manual
FCC Warning
This device has been tested and found to comply with limits for a
Class A digital device, pursuant to Part 2 and Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses and radiates radio frequency energy and, if not
installed and used in accordance with the user’s manual, may
cause interference in which case user will be required to correct
the interference at its own expense.
NOTICE:
1. The changes or modifications not expressively approved by
the party responsible for compliance could void the user's
authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be
used in order to comply with the emission limits.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European
Community and meets or exceeds the following technical
standard.
EN 55022 - Limits and Methods of Measurement of Radio
Interference Characteristics of Information Technology
Equipment. This device complies with CISPR Class A.
WARNING:
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the user
many be required to take adequate measures.
Introduction
The splitter is a Power Over Ethernet splitter. It split the data and
power from the cable come over PSE. When the input port
connects to PSE via Cat5 cable, the splitter will pass-through the
data signal to its RJ-45 output port, and also converter the 48V
PoE power to DC5V/7.5V/9V/12V 1A to the output power jack.
With this splitter, a client device without PD feature also can enjoy
the power from PSE device.
Product Features
Complies with IEEE802.3u 10Base-T/100Base-TX,
IEEE802.3ab, IEEE-802.3af PoE Standards.
TP port support Auto-MDIX & Auto-negotiation.
TP port up to 100 meters for shielded/unshielded twisted pair
cable.
Supports Full-duplex & Half-duplex operation on TP base on
Auto-negotiation.
Supply power source of 5V/7.5V/9V/12V up to 1A peak.
Small dimension, can easily install anywhere.
Technical Specifications
Standards
IEEE 802.3u
10Base-T/100Base-TX/IEEE802.3ab
100Base-T and IEEE 802.3af
Media support
10BASE-T EIA/TIA 568 Cat3, 4, 5, 5e
or 6 UTP/STP.
100Base-TX EIA/TIA568 Cat5, 5e or
6 UTP/STP.
Distances support
Twisted pair STP120 meters / 393ft.
Output Power
DC 5V/7.5V/9V/12V
Data Transfer Rate
100Mbps/10Mbps.
LED indicators
Power on
Temperature
0℃to 40℃(Operating).
-20℃to 90℃(Storage).
Humidity
10% to 90% (Non-condensing).
Certifications
FCC Class B, CE
Dimensions
70 50 25 mm (L W H).
Weight
66g.
Package Contents
Before you start to install this switch, please verify your package
that contains the following items:
One Splitter
One Power output cable
One User’s Manual
Installation
I. The TP input port
Using this port to connect to the PSE port of PoE switch or
Power injector Hub.
II. The TP output port
Using this port directly connect to the TP port of client device
(i.e.: a IP Cam, wireless Ap..)
III. The Power output port
Using the power jack cable to connect to the client device,
supply 5V/7.5V/9V/12V 1A to the client device
The LED indicators
LED
Color
Status
Description
Power
Yellow
On
Power on
Altri manuali COP Convertitore multimediale
