Courtyard HYPH4601-7 Manuale utente
Owner’s Manual
Breckenridge Induction Heater
Item# 51161
Model# HYPH4601-7
WARNING
Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Read the owner’s manual thoroughly before installing or servicing this
result causing property damage, personal injury or loss of life.
DANGER
WARNING
WARNING
If you smell gas:
1. Shut off gas to the appliance.
3. If odor continues, keep away from
the appliance and immediately call
e department.
Do not store or use gasoline or other
vicinity of this or any other appliance.
An LP-cylinder not connected for use
shall not be stored in the vicinity of
this or any other appliance.
For outdoor use only.
Save these instructions for future use. If
you are assembling this unit for someone
else, give this manual to him or her to read
and save for the future.
Bond Manufacturing Co., Inc. | Page 2
WARNING
Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so
SAFETY INFORMATION
•The installation of this unit must adhere to local codes or either the National Fuel Gas Code, ANSI
Z223. 1/NFPA54, OR CAN/CGA-B149.1, National Gas and Propane Installation Code.
•THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a
ventilated space and shall not be used in any enclosed area.
•This unit is to be used with propane gas only! (sold separately)
•Do not attach a remote gas supply to this unit.
•Only use propane gas for this unit.
•This unit is not intended for natural gas.
•Converting this unit to natural gas is dangerous and not recommended. The conversion of this unit
will void the manufacturer warranty.
•If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following:
•Never install or remove a propane tank from this unit while it is in use.
•Applying too much propane may result in gas pooling and will not burn. Allow fresh air into the unit
so that the remaining gas may escape.
•
•
•
•
•
•Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and
should be inspected by a gas supplier.
•Do not operate unit until all parts are fully assembled.
•Do not paint or color any part of this heating unit.
•Unit may be hot while in use, do not attempt to move it while in use.
•Never leave this heating unit unattended while in use.
•This unit is not intended for cooking.
•
•Keep a safe distance to avoid burning skin or clothing.
•Do not sit or rest hands or feet on this heating unit.
•
•Keep all electrical cords and fuel supply hose away from heated surfaces.
•Combustible materials should not be within 61 cm / 24 in of the top of the unit, or within 61 cm /
24 in around the entire unit.
•
vapors and liquids.
•Never use the unit in spaces which may contain volatile or airborne combustibles.
•
•Do not add water into the unit.
•Do not operate unit if any part has been under water. Call a service technician to replace any
The max. inlet supply pressure: max. Gas supply 27.94 cm / 11 in w.c. (2.74kPa)
Use LP propane tanks with the following dimensions: (30.5 cm D / 45.72 cm H) (12 in D / 18 in H) -
capacity 9.08 kg / 20 lbs. You must use a propane tank that has a collar to protect the gas valve.
The tank system must be set up for vapor withdrawal.
1-866-771-2663 | Page 3
damaged part should this occur.
Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied
directly by Bond Manufacturing Co., Inc.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas
valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.
•Do not disconnect any part while unit is in use.
•Do not store a spare propane tank on or near this unit.
•If the heating unit is indoors, detach the propane tank and leave outdoors.
•Y.
•Always remove protective cover before operating (if applicable).
•Do not set the protective cover over the unit until it is turned off and completely cooled down.
•Check for leaks after not using the unit for long periods of time.
•Children should never operate this unit. Children must be supervised while near this unit.
•Keep gas tank at least 152.4 cm / 5 ft. away from unit when lit. (if external tank)
•The maximum gas supply pressure is 250psi.
•All installation and repair should be done by a qualified professional. This unit should be
inspected annually and cleaned regularly.
•Inspect all elements of this heating unit before each use. If there is damage, the burner must be
replaced.
•Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or
injury.
•
of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP gas
tanks, spheres and tubes for Transportation of Dangerous Goods; and Commission.
•Type I, (CGA791) LP
gas tank connection.
•
•Inspect the gas hose and all connections to the propane tank prior to each use.
•Always follow lighting instructions carefully.
•Do not use 30 lb. propane tanks for this unit.
•In case of high winds, secure this unit to the ground to prevent the unit falling over.
•Children and adults should be alerted to the hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
•Young children should be carefully supervised when they are in the area of the appliance.
•Clothing or other flammable materials should not be hung from the appliance or placed on or
near the appliance.
•Any guard or other protective device removed for servicing the appliance shall be replaced
prior to operating the appliance.
•Installation and repair should be done by a qualified service person. The appliance should be
inspected before use and at least annually by a qualified service person. More frequent cleaning
may be required as necessary. It is imperative that the control compartment, burners and
circulating airways of the appliance are kept clean.
Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate
the appliance. For assistance with repair or replacement of the burner or any other parts, call Bond
Manufacturing Co., Inc. at
1-866-771-BOND (2663)
Bond Manufacturing Co., Inc. | Page 4
HARDWARE
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part appears missing or damaged, don't use this product
and call customer service immediately.
Estimated assembly time: 30 minutes.
Tools required for assembly (not included): Phillips Screwdriver, Wrench.
Combustible materials should not be within 61
cm / 24 in of the top of the unit, or within 61 cm
/ 24 in around the entire unit.
SAFETY INFORMATION
Min. Clearance
61 cm / 24 in
Min. Clearance
61 cm / 24 in
Min. Clearance
61 cm / 24 in
BE CAREFUL: WHEN CERTAIN MATERIALS OR
ITEMS ARE STORED ABOVE, BESIDE OR UNDER
THIS HEATER WHILE IN USE, THEY WILL BE
SUBJECT TO RADIANT HEAT AND COULD BE
SERIOUSLY DAMAGED.
ytQnoitpircseDmetI
3tuNpaC6MAA
4M6 NutBB
3tuN8MCC
3tuNgniW5MDD
3sdutS6MEE
3sdutS8MFF
4Anchoring NutGG
AA BB CC DD EE FF GG
1-866-771-2663 | Page 5
Item Description Qty
A Tank Supporter 1
B Glass Tube Ring 1
C Door (preassembled) 1
D Reflector 1
E Upper Radiation Screen 1
F Lower Radiation Screen 1
G Body 1
H Glass Tube 1
I Mesh Guard 3
J Upper Supporter 3
K Battery (AA) 1
CONTENTSCONTENTS
H
I
D
E
F
G
J
B
A
K
C
L
L Protective cover 1
BB
G
A
G
DD
J
G
B
Bond Manufacturing Co., Inc. | Page 6
ASSEMBLY INSTRUCTIONS
2. Slide the 3 upper supporters (J) into the slots
in the burner at the top of the body (G). Be sure
that they are fully inserted. Tighten the upper
supporters (J) with 3 M5 wing nuts (DD).
Note: Be sure that the hook on the upper
supporter is upwards.
3. Remove the 3 preassembled screws from the
burner at the top of the body (G). Attach the glass
tube ring (B) to the top of the burner using the 3
preassembled screws you just removed.
1. Flip the body (G) upside down on a protected
surface. Remove the glass tube (H).
Attach the tank supporter (A) to the bottom of the
body (G) using 4 M6 nuts (BB). Flip the body (G) over.
Note: Make sure the wing nut on the tank
supporter (A) faces the door on the body (G).
B
H
F
E
D
AA
EE
CC
FF
J
J
1-866-771-2663 | Page 7
4. Place the glass tube (H) into the top of the glass
tube ring (B).
reppuehtmorfswercs5M3evomeR...666
supporters (J). Place the r
in the previous step onto the upper supporters (J).
Tighten together with 3 M5 screws just removed
from the upper supporters (J).
5. Insert 3 M8 studs (FF) in between lower
radiation screen (F) and upper radiation screen (E).
Fasten the studs with 3 M8 nuts (CC). Then insert
3 M6 studs (EE) between the upper radiation
cap nuts (AA).
Bond Manufacturing Co., Inc. | Page 8
ASSEMBLY INSTRUCTIONS
7. Attach the 3 mesh guards (I) onto the hooks at
the top of the upper supporters (J).
8. Open the door (C). Place the propane gas
tank (not included) into the tank supporter.
Tighten the preassembled wing screw clockwise
to ensure the propane tank is secure.
Close the door after the tank is connected to
the regulator (see below).
CYLINDER VALVE
PRESSURE
RELIEF VALVE
BLEED-OFF
VALVE
BLACK COUPLING NUT
REGULATOR
turn clockwise to connect
turn clockwise
to reseal
9. Turn the cylinder valve on the tank
clockwise to close the propane tank.
Attach the preassembled regulator to the
cylinder valve by turning the regulator
coupling nut clockwise. Make sure it is
fastened securely and tighten connections
by hand only.
J
I
K
GG
1-866-771-2663 | Page 9
OPERATION
•The glass tube may break if it is wet while in use; never use the heater while it’s raining outside.
•Do not splash any liquid on the heater while it is in use.
•Keep children away from the unit while in use; the glass tube may be extremely hot while in use.
Do not touch.
over.
•Never use the heater if the glass tube shows any cracks.
Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor
area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off”
position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles
occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the
gas valve off, disconnect propane gas tank and do not use the appliance until the leak is is
repaired.
heating item.
10.
11. Use the 4 anchoring nuts (GG) to attach the
heater in place to the ground.
Remove the rubber cap on the electronic igniter
by unscrewing and slide battery (K) into the
battery slot. Make sure the positive side of the
battery faces outwards. Screw the electronic
igniter cap over the battery tightly.
Bond Manufacturing Co., Inc. | Page 10
OPERATION
To Light
To Extinguish
1. Unscrew the ignition button on the burner to see if the battery (K) has already been placed inside.
If the battery (K) is not already within the ignition button on the burner, please place the battery
(K) into the ignition button slot.
2. Make sure the ignition control knob is turned to the “off” position. Connect propane gas tank and
slowly open the valve on the propane gas tank by turning the knob counterclockwise.
3. Press in and turn the ignition control knob to the “pilot” position; hold down for 1 minute.
4. Push the ignition button, while still holding down control knob down, to generate a spark.
5. Check to see if there is a pilot light through the glass tube (H). If there is, turn the control knob to
the “low” position.
6. n the control knob to the “high” position.
1. Push and turn the ignition control knob clockwise to the “off” position.
2. Turn the propane gas tank valve on the gas tank to close the gas supply and disconnect the
propane gas tank.
in property damage, personal injury or death.
between 51 - 71.2 cm /20 - 28 in
in height.
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Manuali Stufa popolari di altre marche
Empire Heating Systems
Empire Heating Systems WCC65 Manuale utente
Wetekom
Wetekom 92 86 43 Manuale utente
Desa
Desa SPC170-F Manuale utente
Watlow
Watlow Watrod Electric Tubular Heaters Manuale utente
Haverland
Haverland ECO-DRY GPS Series Manuale elenco delle parti
Stelpro
Stelpro ASILVC2060 Series Manuale utente