COVER VALET PRO Manuale utente
TM
PRO
Premium Hot tub Cover Lifter
TM
2x
Parts
Channel Bracket (prBB) Side Mount Bracket (prAA)
Connection Bar 1 (prEE-a)
Connection Bar 2 (prFF-a)
Connection Bar 3 (prFF-b)
Extension Arm (prDD)
2x
Pivot Arm (prCC)
2x
Locking Gas Shock (prLS) Regular Gas Shock (prRS)
1x
Finger (prEE-b)
2x
1x
2x
1x
1x
2x
TM
Hardware
Medium Hex Bolt (prC)
Large Screw Cap
(prJ)
Plastic Support
(prPS)
Short Hex Bolt (prD)
Medium Screw Cap
(prK)
Small Screw Cap
(prL)
Large Washer
(prM)
Small Washer
(prN)
Long Hex Bolt (prB)
Set Screw (prH)
Lag Screw (prA)
Self Tapping Screw (prG)
Large Lock Nut (prE)
Small Lock Nut (prF)
Screw Sleeve (prI)
2x
24x
2x
10x
28x
16x
24x
8x
4x
4x
4x
4x
12x
10x
16x
steP 1 Assembling brAcket
4x8x
8x
1x
1x
4x
WIDE
• Line up the slotted holes on the
Channel Bracket (prBB) to the
Side Mount Bracket (prAA) and
bolt them together using at least
4 Short Hex Bolts (prD), 8 Large
Washers (prM), and 4 Large Lock
Nuts (prE). The Channel Bracket
(prBB) should hang over the edge
of the Side Mount Bracket (prAA).
Note: The Side Mount Bracket (prAA) has a wider side and a
narrower side. If your cover is extra wide mount the
Channel Bracket (prBB) so the wider side extends outward.
(See Figure 1)
Figure 1
NARROW
TM
steP 2 mounting brAcket
4x4x
• Place the assembled bracket against the side of the spa. The Side Mount
Bracket (prAA) must be flush with the side of the spa. DO NOT allow the Side
Mount Bracket (prAA) to hang over the rounded edge.(See Figures 2 and 3)
• The rear edge of the Channel Bracket (prBB) should be 2 inches from the
rear edge of the acrylic (See Figure 3). The top of the Side Mount Bracket
(prAA) should be flush with the top of the spa cabinet.
• Use 4 Lag Screws (prA) to mount the Side Mount Bracket (prAA) to the side
of the spa.
• Cover the Lag Screws (prA) with Small Screw Caps (prL)
REPEAT STEPS 1 AND 2 ON THE OPPOSITE SIDE OF THE TUB
Figure 3
Figure 2
steP 3 instAlling shocks
1x
1x
1x
1x
• Place the piston end of the Locking Gas
Shock (prLS) into the Plastic Support
(prPS)
• Fasten the Locking Gas Shock to the
Channel Bracket (prBB) using the Long
Hex Bolt (prB), the Screw Sleeve (prI),
the Small Lock Nut (prF), and 2 Small
Washers (prN) as shown in Figure 4.
• Place Medium Screw Caps (prK) over
the Small Lock Nut (prF) and Long Hex
Bolt (prB)
The Locking Gas Shock (prLS) MUST be installed on
the side of the spa where you will operate the lift.
REPEAT STEP 3 FOR THE OPPOSING SIDE
USING THE REGULAR GAS SHOCK (prRS)
Figure 4
2x2x
TM
steP 4 instAlling Pivot Arm
1x
1x
1x
• Attach the Pivot Arm (prCC) to the
Channel Bracket (prBB) using the Long
Hex Bolt (prB), Screw Sleeve (prI), the
Small Lock Nut (prF), and 2 Small
Washers (pN). (See Figure 5)
• Ensure that Pivot Arm (prCC) swings
up and down easily.
• Place Medium Screw Caps (prK) over
the Small Lock Nut (prF) and the head
of the Long Hex Bolt (prB)
REPEAT STEP 4 ON THE OPPOSING SIDE
Figure 5
2x2x
steP 5
•Each Connection Bar 1 (prEE-a) will slide inside each end of Connection
Bar 2 (prFF-a). Make sure that the single holes in each Connection Bar 1
face outward and are oriented in the same direction.
•Using Self Tapping Screws (prG), screw the bars together at a length
matching the distance between the Channel Brackets(prBB).
•Insert the tapered end of Connection Bar 3 (prFF-b) into Connection Bar
2 (prFF-a) and secure using 3 Self Tapping Screws (prG).
• Slide each Connection Bar 1 (prEE-a) into the ends of the attached bars.
Make sure that the single holes in each Connection Bar 1 face outward
and are oriented in the same direction.
•Using Self Tapping Screws (prG), screw the bars together at a length
matching the distance between the Channel Brackets(prBB).
2x
2x
Under 6½ ft
Over 6½ ft
1x
1x
1x
Assembling connection bAr
Depending on the width of your spa this step will vary.
Start by measuring the
distance between the Channel
Brackets(prBB) mounted on
the spa.
TM
steP 6
Assembling connection bAr
• Slip the Fingers (prEE-b) under the
seam in the middle of the spa
cover. The larger hole of the
Extension Arm (prDD) should be
facing Up. See Figure 8
• Insert both ends of the assembled
connection bar from Step 5 into
the larger holes of the Extension
Arm (prDD) Plastic Support (prPS)
and fasten them using Set Screws
(prH) as shown in Figure 9.
Figure 8
Figure 9
2x
2x
• Insert Finger (prEE-b) into the hole on
the Extension Arm (prDD) so it extends
inward toward the tub. Fasten with Set
Screw (prH) as shown in Figure 7.
Figure 7
REPEAT THIS STEP ON THE OTHER
EXTENSION ARM. BE SURE TO
MOUNT THE FINGER FACING THE
OPPOSITE DIRECTION.
Assembling the cover lifter A
steP 7 Assembling the cover lifter b
• Slide the Extension Arms(prDD) into the Pivot Arms(prCC), making sure
to center the spa cover over the spa. See Figure 10.
• Once the spa cover has been centered, fasten the Extension Arm (prDD)
to the Pivot Arm using Self Tapping Screws (prG). Cover with Small
Screw Caps (prH).
•If your cover has
locking clips that hold
it down when closed,
fasten them on the
end of the spa where
the cover rests while
folded. See Figure 11.
6x6x
*You will need at least one person to help hold the cover during this step
Figure 11
Figure 10
Altri manuali per PRO
1
Indice
