CP Plus CP-UNR-4K2081-V2 Manuale utente
Quick Start Guide
V1.0
2
Welcome
Thank you for purchasing our NVR!
This quick start guide will help you become familiar with our NVR in a very short time.
Before installation and operation, please read the following safeguard and warningcarefully!
Important Safeguard and Warning
All installation and operation here should conform to your local electrical safetycodes.
We assume no liability or responsibility for all the fires or electrical shock caused by improper
handling or installation.
We are not liable for any problems caused by unauthorized modifications or attemptedrepair.
Improper battery use may result in fire, explosion, or personalinjury!
When replace the battery, please make sure you are using the samemodel!
Note: All the installation and operations here should conform to your local electric
safety rules.
1. Check Unpacked NVR
When you receive the NVR from the forwarding agent, please check whether there is any visible
damage. The protective materials used for the package of the NVR can protect most accidental
clashes during transportation. Then you can open the box to check the accessories.
Please check the items in accordance with the list. (Remote control is optional). Finally, you
can remove the protective film of the NVR.
2. About Front Panel and Rear Panel
For detailed information of the function keys in the front panel and the ports in the rear panel,
please refer to the User’s Manual included in the resource CD.
The model in the front panel is very important; please check according to your purchase order.
The label in the rear panel is very important too. Usually we need you to represent the serial
number when we provide the service after sales.
3
3. HDD Installation
This series NVR has only one SATA HDD. Please use HDD of 7200rpm or higher.
Please follow the instructions below to install hard disk.
All figures listed here are for reference only.
1. Loosen the screws of the
rear panel and side panel.
2. Fix four screws in the HDD
(Turn just three rounds).
3. Place the HDD in accordance with
the four holes in the bottom.
4. Turn the device upside down and
then turn the screws in firmaly
5. Fix the HDD firmly.
6. Connect the HDD cable and
power cable.
7. Put the cover in accordance with the
clip and then place the upper cover back.
8. Secure the screws in the rear
panel and the side panel.
4
4. Specification
Model
CP-UNR-4K2081-V2
Dual-core embedded processor
System
Main Processor
Operating System
Embedded LINUX
8 channels
Video& Audio
IP Camera Input
Two-way Talk
1channel Input, 1channel Output, RCA
1 HDMI, 1 VGA
Display
Interface
Resolution
3840×2160, 1920×1080, 1280×1024, 1280×720,
1024×768
Display Split
1/4/8/9
OSD
Camera title, Time, Camera lock, Motion detection,
Recording
Smart H.265/H.264
Recording
Compression
Resolution
8Mp,6Mp, 5Mp, 4Mp, 3Mp, 1080P, 720P & D1 etc.
Record Rate
Max 80Mbps
Bit Rate
48~ 8192kbps
Record Mode
Manual, Schedule (Regular (Continuous), MD, Alarm),
Stop
Record Interval
1~120 min (default: 60 min), Pre-record: 1~30 sec,
Post-record: 10~300 sec
Recording, PTZ, Tour, Alarm, Video Push, Screen tips
Video Detection &
Alarm
Trigger Events
Video Detection
Motion Detection, MD Zones: 396(22×18), & Camera
Blank
1/4/8/9
Playback & Backup
Sync Playback
Search Mode
Time/Date, Alarm, MD & Exact search (accurate to
second), Smart search
Playback Function
Play, Pause, Stop, Rewind, Fast play, Slow play, Nextfile,
Previous file, Next camera, Previous camera, Full screen,
Repeat, Shuffle, Backup selection, Digital zoom
Backup Mode
USB Device/Network/Internal SATA burner
1 RJ-45 port (10/100/1000Mbps)
Network
Ethernet
Network Function (to be
determined)
HTTP, HTTPS, TCP/IP, IPv4, RTSP, UDP, NTP, DHCP,
DNS, IP Filter, DDNS, IP Search (Support Dahua IP
camera, DVR, NVS and etc.)
Max. User Access
128 users
Smart Phone
iPhone, iPad, Android, Windows Phone
Storage
Internal HDD
1 SATA III ports, up to 6TB
Auxiliary Interface
USB
2 USB2.0
DC12V/2A
Power Supply
Power Consumption
NVR: 2.4W for normal model (without HDD & IPC)
Working Environment
-10°C~+55°C/10%~90%RH/86~106kpa
5
General
Dimension
(W×D×H)
Compact 1U, 260mm×220mmx45mm
Weight
0.7~0.8KG for normal model(without HDD) (to be
determined)
5. Front Panel
For detailed operation instruction of other series, please refer to the User’s Manual included
in the resources CD.
Please refer the below Front Panel. Figure 1
Figure 1
SN
Name
Function
1
HDD status indictor light
The red light becomes on
when HDD is abnormal.
2
Power indicator light
The red light becomes on
when the power connection is
OK.
3
Network status
indicator light
The red light becomes on
when the network connection
is abnormal.
6
6. Rear Panel
For detailed operation instruction of other series, please refer to the User’s Manual included
in the resources CD.
The rear panel is shown as in Figure 2 (Picture for reference only).
Figure 2
Please refer to the following sheet for detailed information.
Port Name
Connection
Function
USB2.0 port
USB2.0 port. Connect to mouse, USB storage
device, USB burner and etc.
Network port
10M/100Mbps self-adaptive Ethernet port. Connect
to the network cable.
HDMI
High Definition
Media Interface
High definition audio and video signal output port.
It transmits uncompressed high definition video
and multiple-channel data to the HDMI port of the
display device. HDMI version is 1.4.
VGA
VGA video output
port
VGA video output port. Output analog video signal.
It can connect to the monitor to view analog video.
GND
Ground end
Power input port
Input DC 12V/2A.
MIC IN
Audio input port
Bidirectional talk input port. It is to receive the
analog audio signal output from the devices such
as microphone, pickup.
MIC OUT
Audio output port
Audio output port. It is to output the analog audio
signal to the devices such as the sound box.
Bidirectional talk output.
Audio output on 1-window videomonitor.
Audio output on 1-window videoplayback.
7
7. Connection Sample
Please refer to Figure 3 for connection sample.
The following figure is based on our CP-UNR-4K2162-V2 series product.
Figure 3
8. Device Initialization
If it is your first time to use the device, please set a login password of admin (system default user).
Note
For your device safety, please keep your login password of admin well after the initialization steps, and
change the password regularly.
Steps:
Step 1 Boot up device.
Device displays device initialization interface. See Figure 4
8
Step 2 Set login password of admin.
Figure 4
User name: The default user name is admin.
Password/confirm password: The password ranges from 8 to 32 digitals. It can contain letters,
numbers and special characters (excluding “'”,“"”,“;”,“:”,“&”) . The password shall contain
at least two categories. Usually we recommend the strongpassword.
Prompt question: If you set the prompt question here. On the login interface, click , devicecan
display the corresponding prompt question for you to remind the password.
WARNING
STRONG PASSWORD RECOMMENDED-For your device own safety, please create a strong
password of your own choosing. We also recommend you change your password
periodically especially in the high security system.
Step 3 Click Next.
Device goes to unlock pattern interface. See Figure 5
9
Step 4 Set unlock pattern.
Figure 5
After set unlock pattern, device goes to password protection interface. See Figure 6
Note
The unlock pattern shall at least contain 4 grids.
Device adopts unlock pattern to login bydefaultif you have setpattern here.If thereis no unlock
pattern, please input the password to login.
Click Skip if there is no need to set unlock pattern.
Figure 6
Step 5 Set security questions.
Note
After setting the security questions here, you can use the email you input here or answer the
security questions to reset admin password.
Cancel the email or security questions box and then click Next button to skip thisstep.
10
Email: Input an email address for reset password purpose. In case you forgot password in the
future, input the security code you got on the assigned email to reset the password of admin. If
Indice
Altri manuali CP Plus Hardware di rete
CP Plus
CP Plus CP-UNR-404T1-MW2 Series Manuale utente
CP Plus
CP Plus CP-UNR-4K2161-V2 Manuale utente
CP Plus
CP Plus CP-VTA-M1143 Manuale utente
CP Plus
CP Plus CP-PVM-70T Manuale utente
CP Plus
CP Plus CP-UNR-4K2041-V2 Manuale utente
CP Plus
CP Plus Orange Guida all'installazione
CP Plus
CP Plus CP-UNR-1xxQ1 Series Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
