CPS FX134 Manuale utente

FX Series Service Manual

Models: FX134, FX1234, FX3030

CPS AUTOMOTIVE RECOVER, RECYCLE, RECHARGE

Table of Contents

PAGE

General Safety Instructions 2

Introduction 3

Summary of Operation 4-10

Section 1 Updating Program, Service Access, and Calibration Procedures 11-21

Section 2 Common Problems and Solutions 22-27

Section 3 Repair Procedures Component Service and Repair Instructions 28-41

Section 4 Reference Materials 42-50

General Safety Instructions

Only qualified service personnel should service this unit. The service personnel should be qualified in

refrigerant and electrical service work. It will be necessary for the service technician to operate the unit

with the service covers removed. Please use extreme caution due to the presence of un-insulated live

electrical parts.

Danger- Electrical Shock Hazard. When servicing this equipment with the front cover opened, live

un-insulated electrical connections will be exposed. An Electrical Shock hazard could result in

severe injury or even death.

Danger- The unit’s recovery tank contains liquid refrigerant. Overfilling of the recovery tank may cause a

violent explosion resulting in severe injury or even death.

Danger- Only use CPS Automotive recommended recovery tanks with this unit. See distributor for

replacement tanks.

Danger- Avoid breathing refrigerant vapors and lubricant vapor or mist. Breathing high concentration

levels may cause heart arrhythmia, loss of consciousness, or even cause suffocation and death.

Caution- all hoses may contain liquid refrigerant under pressure. Contact with refrigerant may cause

frostbite or other related injuries. Wear proper personal protective equipment such as safety goggles and

gloves. When disconnecting any hose, please use extreme caution.

Caution- avoid breathing refrigerant vapors and/or lubricant mist. Exposure may irritate eyes, nose,

throat, and skin. Please read the manufacturers Material Safety Data Sheet for further safety information

on refrigerants and lubricants.

Caution- to reduce the risk of fire, avoid the use of extension cords thinner than NO. 14 awg.

(1,5m1,5mm²) to prevent the overheating of this cord please keep length to a minimum.

Caution- do not use this equipment in the vicinity of spilled or open containers of gasoline or other

flammable substances. Make certain that all safety devices are functioning properly before operating the

equipment.

Mixing of different refrigerants will cause this equipment and the mobile A/C system to prematurely fail.

Note: It is very expensive to destroy mixed or damaged refrigerants.

Make sure that recovery tank is placed on the load cell platform at all times. Failure to do so will disable

certain safety features of this unit.

Introduction

The FX series is a fully automatic Recovery/Recycling, and Recharging Refrigerant work station. The

FX134 Series meets and exceeds the new SAE J2788. FX1234 Series meets and exceeds the new

J2843/J2788. The FX3030 Series meets and exceeds J3030. The FX134, FX1234, and FX3030 Series

models are single circuit R/R/R machines for handling R134a, R1234yf from mobile AC systems. The

following table will give you more information on the models available, the power supply and the CPS

Automotive tank models available for the FX 134, FX1234, and FX3030 Series.

CAUTION: The FX134, FX1234, and FX3030 series uses the integrated scale for tanks overfill

protection. The information on Maximum Refrigerant and Empty Tank weights must be accurately

inputted or the overfill protection will not function correctly. See Warnings and Dangers of overfilling a

tank.

CPS Models Voltage Hz

FX134/FX1234/FX3030 115 50/60

FX134E/FX1234E/FX3030E 220-240 50/60

FX134J/FX1234J/FX3030J 100 50/60

CPS Tank Max Refrigerant Empty Tank

Models Weight Weight

CRX400T* 38 lbs. 0 ounces 28 lbs 8 ounces *

CRX390T 68 lbs. 0 ounces 57 lbs 8 ounces

40L 33.64 KG 20.9 KG

OTHER1 2 3

* comes standard on FX134/FX1234/FX3030

1 The unit can be configured to most approved recovery tanks. Data from the tank manufacturer will be

required to complete the tank configuration process. See Section 1 for tank configuration details.

Many problems are a result of operator error. Please read the FX134/FX1234/FX3030 Series

operating manual. The manual is separated into 4 Sections:

Section 1 gives instructions on how to gain service access to the FX134/FX1234/FX3030. This Section

also gives instructions on proper calibration and mechanical repair procedure

Section 2 contains a list of common problems and how to resolve them.

Section 3 contains instructions on how to repair various components used in the

FX134/FX1234/FX3030Series.

Section 4 contains additional Electrical and Plumbing Schematics of the FX134/FX1234/FX3030Series.

This section also contains the FX134/FX1234/FX3030Series parts list.

SUMMARY OF OPERATION

The following information will help illustrate the flow path of the FX134/FX1234/FX3030 series in each

of the unit’s modes. Understanding what valve, component, etc… that each mode utilizes will help with

faster diagnose and repair the unit.

RECOVER/RECYCLE

NOTE: The FX1234 and FX3030 will implement refrigerant indentifying process according to J2743. Refrigerant sample

will pass through (SC2) low side service hose. The refrigerant sample will then pass through low side manifold valve (LV2)

and (LS2) solenoid valve allow sample into identifier. Once refrigerant has been sampled and passes. The recovery unit will

operate as instructed below. See Identifier Plumbing Schematic.

The Manifold gauges read the respective service line pressures. The recovered refrigerant will pass through their

respective open HI and LO manifold valves (LV1, LV2). The combined HI and LO refrigerant then flows through

the open RECOVER valve (LV4) and then into a Constant Pressure Regulator. The REGULATOR reduces the

pressure down to 80 psig where it flows into a DOA Chamber where oil is separated from refrigerant (if liquid is

present) the liquid refrigerant is boiled off by the heat exchanger in DOA Chamber. After leaving the DOA

Chamber, the vapor refrigerant enters the COMPRESSOR suction where it is compressed to a high pressure gas.

This completes the first step in the recycling process. The refrigerant then passes through the heat exchanger in

DOA Chamber then to RECOVERY OUT valve (HV1) and passes by the systems HIGH PRESSURE SWITCH

(HP) on its way to the storage tank. If the pressure goes above 450 psig, the HP will open and disrupt power to the

unit’s compressor and signals to the control PCB that a HIGH PRESSURE LIMIT condition exists. Recovery is

complete when the Pressure Transducer (PT) senses the required vacuum. When recovery is complete, the

automatic oil drain will commence for 45 seconds.

RECOVER- Oil Drain Flow

Once Recover is done and the compressor shuts off. The air purge valve HS1 will open to pressurize DOA

Chamber then HS1 will close. The compressor will come on to lower pressure in DOA for oil draining. Once

pressure level is achieved, then (HV3) opens allowing excess oil to drain from DOA Chamber for 30 seconds.

EVACUATION

After the mobile a/c system is repaired, it should then be pulled into a deep vacuum to remove residual gasses and

moisture before recharging it with refrigerant. The unit evacuates gasses from the a/c system through the LO Side

and HI Side service hoses. The gasses enters the unit through the two service hoses attached to the LO and HI

Manifold. The gasses will then pass through their respective open LO and HI valves (LV1 and LV2). The combined

HI and LO gasses then flows through the open EVACUATION valve (LV3) and then into the VACUUM PUMP.

The VACUUM PUMP exhausts the evacuated gasses to the atmosphere.

IMPORTANT: if either the LO or HI manifold gauges read more than 5 psig, the unit will not start the evacuation

mode, but go into the RECOVER mode to recover the gasses causing the pressure.

The Evacuation mode will run per the programmed time set by the user.

CHARGE LOW SIDE

NOTE: FX1234 and FX3030 will have addition steps in charging according to J2743. There will be a 10 minute vacuum test.

The first 5 minutes the vacuum pump mode will run. (See Vacuum Plumbing Schematic) Then the second 5 minutes of the

vacuum leak test is where it checks for vacuum loss. Then a 15% of programmed charge is released for pressurizing A/C for

manual leak check using electronic leak detection. The unit will complete charge once all has passed as instructed below.

Using the keypad to program the desired charge, the liquid refrigerant from the storage tank will pass through the

FILTER DRIER (F2). This completes the third and final procedure of the recycling process. Once through the

FILTER DRIER (F2), the liquid refrigerant will then pass through the open CHARGING SOLENOID VALVE

(LS1). The liquid refrigerant will then pass through the open Low Manifold valve (LV2) and onward through the

Low service hose. After the required amount of refrigerant is charged, the control PCB de-energizes charging

solenoid valve (LS1). The LCD display charge complete, and ask if you want to go to Car Health. If you select to

use Car Health the screen will ask you to start car, and low side (LV2) will open and allow running pressures to be

seen at the pressure transducers. The screen will then display digital manifold and operating pressures on hi and low

side of A/C system. If you choose not use the Car Health, then the screen will ask you to close hi coupler and start

cars A/C system. The low and hi service hoses will then open (LV1 and LV2) and allow suction of car A/C

compressor to clear hoses.

CHARGE HI SIDE

NOTE: FX1234 and FX3030 will have addition steps in charging according to J2743. There will be a 10 minute vacuum test.

The first 5 minutes the vacuum pump mode will run. (See Vacuum Plumbing Schematic) Then the second 5 minutes of the

vacuum leak test is where it checks for vacuum loss. Then a 15% of programmed charge is released for pressurizing A/C for

manual leak check using electronic leak detection. The unit will complete charge once all has passed as instructed below.

The a/c system should be in a deep vacuum before proceeding. After using the keypad to program the desired

charge, the liquid refrigerant from the storage tank will pass through the FILTER DRIER (F2). This completes the

third and final procedure of the recycling process. Once through the FILTER DRIER (F2), the liquid refrigerant

will then pass through the open CHARGING SOLENOID VALVE (LS1). The liquid refrigerant will then pass

through the open HI Manifold valve (LV1) and onward through the HI, Lo, or both service hoses depending on

what was selected. After the required amount of refrigerant is charged, the control PCB de-energizes charging

solenoid valve (LS1). The LCD display will read “CHARGE COMPLETE” and give an audible signal.

CHARGE BOTH LOW AND HI SIDE