Crane NRI G-13.mft Standard Guida
National Rejectors, Inc. GmbH • Zum Fruchthof 6 • D-2 6 4 Buxtehude
Phone: +49 (0) 4 6 -729-0 • Fax: +49 (0) 4 6 -729- 5 • E-Mail: [email protected] • Internet: www.nri.de
Technical Documentation
.05 Hns/ds
Edition .0
KA.cctalkPC-GB
Electronic coin validator
G-13.mft cctalk
Installation and testing instructions for PC applications
TABLE OF CONTENTS
3
G- 3.mft cctalk for PC applications
National Rejectors, Inc. GmbH, Buxtehude
Ta le of contents
1 A out these instructions 5
2 The PC solutions for G-13.mft cctalk 6
Power supply 6
Connection to PC 7
Variant : Connection using RS-232 adapter 7
Variant 2: Connection using USB adapter 8
Variant 3: Connection using integrated USB port 8
Installation of the USB driver 9
3 Demo software 10
System requirements 0
Install demo software 0
Starting demo software
Testing G- 3.mft cctalk functions 2
ABOUT THESE INSTRUCTIONS
5
G- 3.mft cctalk for PC applications
National Rejectors, Inc. GmbH, Buxtehude
1 A out these instructions
These instructions describe how to connect the G- 3.mft cctalk to a PC and
how to test the functions of the device connected using a demo software.
These instructions do not replace the detailed operating
instructions of the validator G-13.mft with serial cctalk
interface, ut rather complete the operating instructions
concerning the G-13.mft cctalk functions in a PC environment.
In order to use the validator’s entire functional range safely
the operating instructions must e read carefully (PDF
download under www.nri.de). They contain all information on:
• Design and function
• Starting-up
• Operation
• G-13.mft-specific cctalk commands, status and error
messages
• Cleaning
• Accessories
INSTALLATION
6
G- 3.mft cctalk for PC applications
National Rejectors, Inc. GmbH, Buxtehude
+
–
2 The PC solutions for G-13.mft cctalk
Variant : Connection by means of the RS-232 adapter G-55.0480 (ordering
code 25588) (see Fig. a)
Variant 2: Connection by means of the USB adapter G-55.048
(ordering code 25589) (see Fig. b)
Variant 3: Connection by means of the integrated USB port (see Fig. c)
Power supply
Use a standard wall power supply with the following technical data to supply
the G- 3.mft cctalk with power for a PC application (e.g. NRI wall power
supply, ordering code 26482):
• 2 V, stabilized
• min. 400 mA
• output connector; 5.0 x 2. ,
INSTALLATION
7
G- 3.mft cctalk for PC applications
National Rejectors, Inc. GmbH, Buxtehude
2
3
1
Fig. 1a: Connection using RS-232 adapter
Connection to PC
There is a difference in the connection to the PC depending on the variant:
Variant 1: Connection using RS-232 adapter
1Connect the NRI RS-232 adapter G-55.0480 (ordering code 25588)
to the validator using the 4-pole cctalk interface 1 on the rear of the
G- 3.mft.
2Connect the adapter to the PC using the RS-232 interface 2.
3Supply the RS-232 adapter with power using socket 3 and the 2-V
power pack.
Now the PC can communicate with the validator.
INSTALLATION
8
G- 3.mft cctalk for PC applications
National Rejectors, Inc. GmbH, Buxtehude
12-V supply
USB PC connection
2
3
1
Fig. 1 : Connection using USB adapter
Fig. 1c: Connection using integrated USB port
Variant 2: Connection using USB adapter
1Connect the NRI USB adapter
G-55.048 (ordering code 25589)
to the validator using the 4-pole
cctalk interface 1
on the rear of the
G- 3.mft.
2Connect the
adapter to the PC
using its USB
interface 2.
3Supply the USB
adapter with power
using socket 3 and the 2-V power pack.
Windows identifies new hardware and searches a driver.
4Install driver (see section "Installation of the USB driver“ in this
chapter).
Variant 3: Connection using integrated USB port
1Connect the G- 3.mft cctalk to the PC using
its USB port and a standard USB cable.
2Supply the G- 3.mft cctalk with voltage using
its power socket and the 2-V power pack.
Windows identifies new hardware and
searches a driver.
3Install driver (see section "Installation of
the USB driver“ in this chapter).
INSTALLATION
9
G- 3.mft cctalk for PC applications
National Rejectors, Inc. GmbH, Buxtehude
Installation of the USB driver
If the G- 3.mft cctalk is operated using a USB port, you have to install a so-
called VCP driver (Virtual COM Port).
The drivers for the Windows versions 95/98/2000/Me/XP are made available
to you in a zip-file on our download pages (www.nri.de).
To install:
1Unpack the driver software CP2 0x.zip into any directory.
2Connect the G- 3.mft cctalk to the PC (see section "Connection to
PC“ in this chapter).
Windows identifies new hardware and searches a driver.
3Select directory, in which you have unpacked the files beforehand.
The driver is installed and the PC can now communicate with the
validator.
The driver provides a virtual COM port. When setting up the
relevant PC application you are asked to specify this
communication port. If there are no further communication devices
connected (modem, I DN, bluetooth, etc.), the G-13.mft cctalk is
on the COM3 port.
Otherwise you can determine the port number by means of the
control panel (device manager) (entry, e.g.: "CP2101 U B to UART
Bridge Controller (COM6)").
0
G- 3.mft cctalk for PC applications
DEMO SOFTWARE
National Rejectors, Inc. GmbH, Buxtehude
3 Demo software
By using the software "cctalk-Demo" the functions of the G- 3.mft with
cctalk interface connected to a PC can be visualized and tested. Control
commands, which are transferred from the PC to the validator during
operation, can be simulated.
System requirements
The "cctalk-Demo" software specifies the following minimum hardware and
software requirements:
Operating system Windows 95b/95c/98/NT/2000/XP (not CE)
Working memory of at least 32 MB
Graphic resolution 800 x 600 dpi min./High Color
The use of the „cctalk-demo“ software requires basic knowledge of
the Windows operating system on the part of the user.
Install demo software
The demo software is made available to you on our download pages
(www.nri.de) as freeware.
To install:
1Download the demo software cctalkDemo.zip on the hard disk of the
PC that is to operate the G- 3.mft cctalk.
2Unpack zip-file.
Installation is completed.
Altri manuali per NRI G-13.mft Standard
1
Indice
Altri manuali Crane Validatore di banconote
