Crestron CAEN-BLOCK-CENCN-2-POE Istruzioni operative originali

CAEN-BLOCK-CENCN-2-POE

Power Distribution Block with PoE

Installation & Operation Guide

Description

The Crestron®CAEN-BLOCK-CENCN-2-POE is an Ethernet to Cresnet bridge that

provides control with a Crestron Automation Enclosure (CAEN). The device is controlled

and powered by LAN PoE (Power over Ethernet). The CAEN-BLOCK-CENCN-2-POE can

control and power all modules in the cabinet and also the devices on the Cresnet®

network.

Installation

WARNING: To avoid re, shock, or death, turn off the power at the circuit breaker or

fuse and test that the power is off before wiring!

NOTE: Observe the following points:

• Install and use this product in accordance with appropriate electrical codes and

regulations.

• A licensed electrician should install this product.

NOTE: Before using the CAEN-BLOCK-CENCN-2-POE, ensure the device is using the

latest rmware. Check for the latest rmware for the CAEN-BLOCK-CENCN-2-POE at

www.crestron.com/rmware. Load the rmware onto the device using Crestron

Toolbox™ software.

NOTE: Unless otherwise indicated, the lighting system specied in this guide is

modular, requiring assembly in the eld by a licensed electrician, in accordance with all

national and local codes.

If an assembled UL®Listed panel is required, Crestron offers this service through its UL

Listed panel shop. This includes complete in factory system conguration and assembly

by Crestron for an additional fee.

Replace the Divider

NOTE: Class 1 and Class 2 wiring must be separated. Ensure that the correct divider is

used.

Replace the divider.

1. Remove the two screws that secure the divider in the enclosure. Discard the screws

and the divider.

2. Using the supplied screws and nuts, secure the new divider to the side of the

enclosure.

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates. Use a QR

reader application on your mobile device to scan the QR image.

From override

switch

Power input (for when there

is no PoE or for when

additional power is needed)

LAN and PoE

from control

network

To Cresnet

devices

Use the gray module

interconnect cable to make

a connection to the left

module in a double-wide

cabinet.

Use the gray module interconnect cable to make a

connection to the module in a single-wide cabinet.

Use the red module interconnect cable to make a

connection to the right module in a double-wide

cabinet.

LEFT RIGHT

SINGLE WIDTH CABINET

DOUBLE WIDTH CABINET

PWR

NET

MSG

RESET

SETUP

TEST LAN PoE

OVER RIDE

POWER

INPUT

OVR

NET B

24 GGG

NET A

24 YZ G

TYPICAL CRESNET

CONNECTION

CAEN-BLOCK-CENCN-2-POE

ETHERNET TO CRESNET BRIDGE

Mount and Wire the CAEN-BLOCK-CENCN-2-POE

The CAEN-BLOCK-CENCN-2-POE must be mounted in accordance with all national and

local codes. Use the two 8B x 1/4” screws, supplied, to attach the

CAEN-BLOCK-CENCN-2-POE to an enclosure. The rst illustration below shows the

CAEN-BLOCK-CENCN-2-POE mounted in a single-wide enclosure; the second illustration

shows the double-wide enclosure.

NOTE: When installing the CAEN-BLOCK-CENCN-2-POE in a single-wide enclosure,

use the gray module interconnect cable to make the connection between the module

and the RIGHT port on the CAEN-BLOCK-CENCN-2-POE.

NOTE: When installing the CAEN-BLOCK-CENCN-2-POE in a double-wide enclosure,

use the red module interconnect cable to make the connection between the right

module and the RIGHT port on the CAEN-BLOCK-CENCN-2-POE. Use the gray module

interconnect cable to make the connection between the left module and the LEFT port

on the CAEN-BLOCK-CENCN-2-POE.

Make connections as called out in the following illustration.

Operation

The following describes the basic operation of the CAEN-BLOCK-CENCN-2-POE.

TEST Button

Press the TEST button to perform a hardware test of the device. The device reports errors

via blink patterns. The device displays error codes using the NET or MSG LED on the

interface. The LED blinks a specic pattern to indicate an error.

For example, when a 3-3 LED blink pattern occurs, the LED blinks three times, pauses for

1 second, blinks three times, pauses for 5 seconds, and then repeats until the error is

corrected. When a 2-1 LED blink pattern occurs, the LED blinks two times, pauses for 1

second, blinks once, pauses for 5 seconds, and then repeats this code until the error is

corrected.

NET LED Feedback

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions:(1) This device may not cause harmful interference and (2) this device must accept any

interference received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

The product warranty can be found at www.crestron.com/warranty.

The specic patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specic information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, Cresnet, and Crestron Toolbox are either trademarks or registered

trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL is either a

trademark or registered trademark of Underwriters Laboratories, Inc. in the United States and/or other

countries. Other trademarks, registered trademarks, and trade names may be used in this document

to refer to either the entities claiming the marks and names or their products. Crestron disclaims any

proprietary interest in the marks and names of others. Crestron is not responsible for errors in

typography or photography.

This document was written by the Technical Publications department at Crestron.

Crestron Electronics, Inc. Installation & Operation Guide - DOC. 7873B

15 Volvo Drive Rockleigh, NJ 07647 (2047083)

Tel: 888.CRESTRON 12.16

Fax: 201.767.7576 Specications subject to

www.crestron.com change without notice.

LED PATTERN ERROR STATE

Error code 1-1 Broken Y Wire

Error code 1-2 Short to 24 V and Y

Error code 1-3 Short to Ground and Y

Error code 2-1 Broken Z Wire

Error code 2-2 Short to 24 V and Z

Error code 2-3 Short to Ground and Z

Error code 3-1 Short Y to Z

Error code 3-2 Y and Z crossed

Error code 3-3 Y and Z unbalanced

LED PATTERN ERROR STATE

Error code 1-1 Com issue Ethernet

Error code 1-2 Com issue NET A

Error code 1-3 Com issue NET B

Error code 2-1 Com issue Ethernet and Cresnet

Error code 2-2 POE low voltage

Error code 2-3 EXT 24V low voltage

Error code 3-1 Overload NET A

Error code 3-2 Overload NET B

Error code 3-3 Overload NET A and NET B

MSG LED Feedback

SETUP Button

Press the SETUP button to enter Autodiscovery mode via Ethernet.

RESET Button

Press the RESET button to perform a hardware reset.

Altri manuali Crestron Unità di distribuzione dell'energia

Crestron

Crestron Cresnet Network Guida

Manuali Unità di distribuzione dell'energia popolari di altre marche

hager

hager SP 015 Manuale utente

Pakedge

Pakedge PowerPak 9 Manuale utente

Pts

Pts 9042 Series Manuale utente

Shure

Shure WA405 Manuale utente

CORNING

CORNING CCH 4U Manuale utente

Panamax

Panamax M4LT-EX Manuale utente

PANCONNECT

PANCONNECT FLAT 3M Manuale utente

Raytheon

Raytheon 138-118 Manuale utente

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Manuale utente

Botex

Botex PSA 322-6 DL Manuale utente

GE QuiXtra 4000 Guida rapida

RDL

RDL EZ Series Manuale utente

StarTech.com

StarTech.com RKPW161915 Manuale del sistema

Vertiv

Vertiv Knürr DI-Strip Rack PDU Manuale utente

ABB

ABB PSBS0065 Manuale

Baumuller

Baumuller BFN 3-1-0007-001 Manuale

Eaton

Eaton StructuredWiringSolutions ESWT41600 Manuale

GE GEK-45404F Manuale utente