Crestron TMK-4L Manuale utente
Crestron TMK-4L & WMKT-4L
Trim Ring Mount Kits
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2007 Crestron Electronics, Inc.
Crestron TMK-4L & WMKT-4L Trim Ring Mount Kits
Contents
Trim Ring Mount Kits: TMK-4L & WMKT-4L 1
Description.................................................................................................................................1
Setup ..........................................................................................................................................2
Supplied Hardware ......................................................................................................2
Installation...................................................................................................................4
Resources.................................................................................................................................10
Industry Compliance ................................................................................................. 10
Reference Documents................................................................................................10
Further Inquiries ........................................................................................................10
Future Updates .......................................................................................................... 10
Return and Warranty Policies .................................................................................................. 11
Merchandise Returns / Repair Service ...................................................................... 11
CRESTRON Limited Warranty.................................................................................11
Installation Guide – DOC. 6390A Contents •i
Crestron TMK-4L & WMKT-4L Trim Ring Mount Kits
Trim Ring Mount Kits:
TMK-4L & WMKT-4L
Description
Trim Ring Mount Kits are the preferred method of mounting the Crestron Isys®
TPS-4L wall mounted touchpanel when a finished appearance within a neatly
trimmed cutout is required. This application is perfect for wallpapering.
NOTE: If mounting into a material other than drywall (for example, wood lectern,
concrete, or rock) use the cutout template, available in the post-construction kit
WMKT-4L. For concrete and rock mounting material, allow for proper ventilation
before mounting the touchpanel.
There are two Trim Ring Mount Kits. The TMK-4L is a pre-construction accessory.
Pre-construction refers to framed walls prior to hanging drywall. This accessory
must be used with either the Pre-Construction Mount Kit (PMK-4L) or Back Box Kit
(BB-4L).
The WMKT-4L is a post-construction kit. Post-construction refers to framed walls
with drywall hung. This accessory is designed with a mounting plate so that it can be
placed anywhere on a wall without the support of a stud. The mounting plate is also
ideal for installing the touchpanel in a lectern.
NOTE: If necessary, consult the latest revision of the TPS-4L Installation and
Operations Guide (Doc. 6449) for a complete list of mounting options. The
document is available from the Crestron website (http://www.crestron.com/manuals).
Installation Guide – DOC. 6390A Trim Ring Mount Kits: TMK-4L & WMKT-4L •1
Trim Ring Mount Kits Crestron TMK-4L & WMKT-4L
Setup
Supplied Hardware
The TMK-4L consists of a metal trim ring that attaches to the BB-4L or PMK-4L.
The WMKT-4L consists of the trim ring found in the TMK-4L as well as a mounting
plate.
The mounting plate provides the necessary support for post-construction
applications. Two overlay cutout templates (4007975) are supplied. One is in the
shape of the required opening; the other is similar to a frame, with the inner area of
the frame the shape of the required opening. (Refer to the illustrations on pages 3 and
4.) Use the template that is most convenient.
Supplied Hardware for the TMK-4L and WMKT-4L
DESCRIPTION PART NUMBER QUANTITY
Metal, Plate, Trim Ring 2013241 1
Metal, Plate, Mounting
(WMKT-4L only) 2013242 1
Screw, #04-40 x 2”, Pan, Phil
(WMKT-4L Only) 2018793 4
Overlay, Template, Wall Cutout
(WMKT-4L Only) 4007975 1
The dimensions of the TMK-4L/WMKT-4L are shown below and on the next page.
Dimensional Drawing – Trim Ring
3.91 in
(9.93 cm)
5.88 in
(14.94 cm)
0.05 in
(1.27 cm)
2.21 in
(5.61 cm)
2 •Trim Ring Mount Kits: TMK-4L & WMKT-4L Installation Guide – DOC. 6390A
Crestron TMK-4L & WMKT-4L Trim Ring Mount Kits
Dimensional Drawing – Mounting Plate
0.06 in
(0..15 cm)
5.55 in
(1 4 .1 0 c m)
6.75 in
(17.15 cm)
Drywall Cutout Template and Dimensions (supplied with WMKT-4L only), 1 of 2
TEMPLATE – OV40086
FOR WMKM-4L OR WMKT-4L ONLY
1 OF 2
1/4 in
(5 mm)
3 13/16 in
(97 mm)
4 1/16 in
(103 mm)
5 5/8 in
(143 mm)
4 5/16 in
(110 mm)
1 5/16 in
(33 mm)
Installation Guide – DOC. 6390A Trim Ring Mount Kits: TMK-4L & WMKT-4L •3
Trim Ring Mount Kits Crestron TMK-4L & WMKT-4L
Drywall Cutout Template and Dimensions (supplied with WMKT-4L only), 2 of 2
6 3/4 in
(172 mm)
TEMPLATE – OV40086
FOR WMKM-4L OR WMKT-4L ONLY
2 OF 2
3/4 in
(19 mm)
4 1/16 in
(103 mm)
3 13/16 in
(97 mm)
1/4 in
(5 mm)
5 9/16 in
(141 mm)
9/16 in
(14 mm)
5 5/8 in
(143 mm)
4 5/16 in
(110 mm)
1 5/16 in
(33 mm)
Installation
This section provides an installation procedure for each Trim Ring Mount Kit. The
“TMK-4L Procedure” starts below and the “WMKT-4L Procedure” starts on page 6.
Be sure to review each procedure before starting.
TMK-4L Procedure
This section provides the necessary steps for the assembly of the TMK-4L with
either the BB-4L or PMK-4L. It is assumed that the BB-4L or PMK-4L has been
secured to the stud according to the instructions in the latest revisions of their
Installation Guides (Doc. 6387 and Doc. 6388 respectively). It is also assumed that
drywall is in place and a rectangular cutout for the touchpanel is made in the drywall.
Complete the steps in the order provided. The only tool required and not supplied is
a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the touchpanel for heat dissipation.
NOTE: When installing into the PMK-4L, verify that the 18 AWG bus wire
securing the cables for the touchpanel remains attached.
1. Verify that the rectangular cutout in the drywall is as level as possible.
2. Insert the symmetrical trim ring into the opening, as shown in the
illustration on the following page.
4 •Trim Ring Mount Kits: TMK-4L & WMKT-4L Installation Guide – DOC. 6390A
Crestron TMK-4L & WMKT-4L Trim Ring Mount Kits
Insert Trim Ring into Opening
TRIM RING (2013241)
IMPORTANT
MAKE DRYWALL CUTOUT AS LEVEL AS
POSSIBLE. MOUNTING PLATE ALLOWS
ONLY MINOR ADJUSTMENT OF THE
TOUCHPANEL.
NOTE: The required PMK-4L or BB-4L is not shown.
3. When the trim ring is in position, bend the top two flanges of the ring
upward and the bottom two flanges downward.
• If mounting into the PMK-4L, bend the flanges approximately 90
degrees.
• If mounting into the BB-4L, bend the flanges back as far as they can
go.
4. Run the necessary cables for the touchpanel and secure them behind the
drywall.
5. The TPS-4L can be installed using the four tapped holes in the PMK-4L or
BB-4L. Refer to the latest revision of the TPS-4L Operations and
Installation Guide (Doc. 6449) for details. Refer also to the comprehensive
illustration on the following page.
Installation Guide – DOC. 6390A Trim Ring Mount Kits: TMK-4L & WMKT-4L •5
Trim Ring Mount Kits Crestron TMK-4L & WMKT-4L
Touchpanel Mounting Using TMK-4L – Exploded View
DRYWALL
TRIM RING
(2013241)
TPS-4L
PMK-4L
TPS-4L
MOUNTING SCREWS (4) #04-40 X 2"
(2018793)
WMKT-4L Procedure
This section provides the necessary steps for the assembly and installation of the
WMKT-4L into a wall. Review the procedure and complete the steps in the order
provided. The only tools or materials required and not supplied are a drywall saw or
equivalent and a level.
CAUTION: Allow an air gap of at least 12 inches (30.48 cm) in the wall cavity
above and below the touchpanel for heat dissipation.
1. Locate an area on the wall that is free of miscellaneous wiring and studs.
2. Make a small hole near the middle of the designated site; verify that the
location is suitable.
NOTE: Make the cutout as level and smooth as possible. The mounting plate allows
for only minor leveling adjustments. If a larger cutout is made accidentally, consider
purchasing the Crestron Mud Mount Kit, MMK-4L. Together with the mounting
plate supplied with the WMKT-4L, it provide a cost-effective means of correction.
Essentially, the combination of these two kits makes up the Crestron Mud Mount Kit
for the wall, WMKM-4L. Simply follow the “WMKM-4L Procedure” in the latest
revision of the Mud Mount Kits Installation Guide (Doc. 6389).
3. Use the drywall saw or equivalent to produce a level, rectangular cutout in
the drywall as shown on page 3 or 4.
6 •Trim Ring Mount Kits: TMK-4L & WMKT-4L Installation Guide – DOC. 6390A
Altri manuali per TMK-4L
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Crestron Rack e supporto
Crestron
Crestron Pre-Construction Wall Mount Back Box... Manuale utente
Crestron
Crestron CPC-TMT Come usare
Crestron
Crestron RMK-1600 Manuale utente
Crestron
Crestron PMK-4L Manuale utente
Crestron
Crestron CCS-UC-200-WSTND Manuale utente
Crestron
Crestron BB-1550CW Manuale utente
Crestron
Crestron WMKU-4SM Manuale utente
Crestron
Crestron RMK-3U Manuale utente
Crestron
Crestron C2N-RMAK Manuale utente
Crestron
Crestron TS-70 Series Manuale utente
Crestron
Crestron BB-1000L Manuale utente
Crestron
Crestron CAEN-MK Manuale utente
Crestron
Crestron RMK-12L Manuale utente
Crestron
Crestron TSS-752-MSMK Manuale utente
Crestron
Crestron DMF-CI-8 Manuale utente
Crestron
Crestron MK-QM-RMCRX Manuale utente
Crestron
Crestron RMK-1500 Manuale utente
Crestron
Crestron PMK-1000L Manuale utente
Crestron
Crestron TMK-2000L Manuale utente
Crestron
Crestron RMK-TPS3000L Manuale utente
