Crestron WPR-48 Manuale utente

Crestron WPR-48

Waterproof Wireless Handheld Remote

Operations Guide

This document was prepared and written by the Technical Documentation department at:

Crestron Electronics, Inc.

15 Volvo Drive

Rockleigh, NJ 07647

1-888-CRESTRON

WARNING: The WPR-48 Waterproof Wireless Handheld Remote has been tested

and found to be waterproof when submerged to a maximum depth of 1 meter, and for

a maximum duration of 30 minutes, per IEC 60529 IPX7 standards. Exceeding these

limits may result in damage to the equipment, possible personal injury, and void the

product warranty.

WARNING: The WPR-48 is shipped from the factory partially assembled. That is,

the eight screws that secure the rear cover to the button faceplate are not fully

tightened, to simplify the process of installing button labels, as described in this

Operations Guide. As such, the unit is not waterproof; exposing it to water may result

in damage to the equipment, possible personal injury, and void the product warranty.

WARNING: After installing button labels, as described in this Operations Guide,

tighten all eight screws that secure the rear cover to the button faceplate evenly just

until the gasket is no longer visible between the button faceplate and the rear cover

(from 1.5 to 2 in/lbs torque, maximum). Do not overtighten the screws. To do so

may damage the gasket such that the unit is no longer waterproof. Exposing

such a unit to water may result in damage to the equipment, possible personal injury,

and void the product warranty.

WARNING: The lanyard, supplied with the lanyard foot, poses a possible

strangulation hazard. Crestron does not recommend placing the lanyard around the

neck as a means of carrying the WPR-48. Do not leave the lanyard, or the WPR-48

with lanyard foot and lanyard attached, unattended in any area where children or

pets may be present.

WARNING: This product contains small parts and is not intended for children. This

product is intended for adult use only.

All brand names, product names, and trademarks are the property of their respective owners.

Crestron WPR-48 Waterproof Wireless Handheld Remote

Contents

Waterproof Wireless Handheld Remote: WPR-48 1

Introduction ...............................................................................................................................1

Features and Functions................................................................................................1

Specifications ..............................................................................................................2

Physical Description....................................................................................................3

Industry Compliance ...................................................................................................5

Setup ..........................................................................................................................................5

Applying Power........................................................................................................... 5

Configuring the WPR-48.............................................................................................5

Setting RF/IR ID via Button Presses ........................................................................... 9

User-Printable Customized Button Labels ................................................................10

Installing/Replacing Button Labels ...........................................................................12

Installing Alternate Foot............................................................................................13

Programming the WPR-48.......................................................................................................14

Earliest Version Software Requirements for the PC .................................................14

Programming with SIMPL Windows ........................................................................14

Uploading and Upgrading........................................................................................................ 18

Communication Settings ...........................................................................................18

Firmware Upgrade..................................................................................................... 20

Problem Solving ......................................................................................................................21

Troubleshooting......................................................................................................... 21

Further Inquiries ........................................................................................................22

Future Updates .......................................................................................................... 22

Return and Warranty Policies ..................................................................................................23

Merchandise Returns / Repair Service ...................................................................... 23

CRESTRON Limited Warranty.................................................................................23

Operations Guide – DOC. 6254A Contents •i

Crestron WPR-48 Waterproof Wireless Handheld Remote

Waterproof Wireless Handheld

Remote: WPR-48

Introduction

Features and Functions

The Crestron®WPR-48 waterproof wireless handheld remote can be configured to

transmit either RF or IR signals, making it perfect for controlling music, television,

lighting and more. The unit is also available in an international version, the

WPRI-48. The unit is safe to use in the shower or hot tub. The rubberized,

immersible case is easy to grip, and will not slip from moist hands.

A streamlined user interface of multi-function pushbuttons makes the WPR-48

simple to use under a variety of conditions. The nine three-position pushbuttons may

be configured in any of four arrangements, providing 9, 18, 27, or 48 possible

functions.

Large customizable labels with electroluminescent backlighting facilitate use under

any lighting conditions.

The WPR-48 can communicate via RF or IR with a number of gateways in a

Crestron control system (Cresnet® system). Since it is compatible with Crestron’s

CNRFGWA and CNRFGWA-418 RF gateways; as well as the MC2W and ST-CP

control systems with a built-in RFGWA gateways, the CNXRMIRD IR receiver, and

the CN-TVAV device controller, the WPR-48 fits easily into any Crestron control

system design.

Functional Summary

The built-in, long-life lithium-ion rechargeable battery provides several weeks of

wireless use on a single charge. It is easily recharged when the remote is placed in

the WPR-DS docking station (included).

•

Nine pushbuttons provide up to three functions per button.

• Configuration settings allow up to 48 possible functions.

• Large customizable labels with electroluminescent backlighting

identify the button functions.

• Long-life lithium-ion rechargeable battery provides several

weeks of wireless use on a single charge.

Operations Guide – DOC. 6254A Waterproof Wireless Handheld Remote: WPR-48 •1

Waterproof Wireless Handheld Remote Crestron WPR-48

Specifications

The following table provides a summary of specifications for the WPR-48.

Specifications of the WPR-48

SPECIFICATION DETAILS

Power Requirements 3.6 VDC Lithium-Ion battery, 750 mAh

Usage per charge: up to 5 hours (backlight On

continuous); up to 4 weeks (typical home use)

Charging time: 1.5 hours (maximum)

Wireless Specifications

RF Transmitter

RF Bandwidth

RF Range

IR Transmitter formats2

IR Range

433 MHz or 418 MHz 1-way RF1

±100 kHz

Up to 300 feet (typical)

38 kHz RC5

455 kHz Crestron format

Up to 15 feet (typical)

Control System Update Files 3, 4, 5

2-Series Control System

CEN/CN-TVAV

CNMSX-AV/PRO

CNRACKX/-DP

ST-CP

All Versions

Default RF ID; IR ID 10

Operating Temperature 32° to 140°F (0° to 60°C)

Humidity 0% to 100% RH (non-condensing)

Dimensions Height: 5.26.in (13.36 cm)

Width: 2.79 in (7.09 cm)

Depth: 1.16 in (2.95 cm) using standard lanyard foot

0.82 in (2.08 cm) using blank foot

Weight 4.8 oz (134.4 g)

1. Requires Crestron CNRFGWA, CNRFGWA-418, or the MC2W or ST-CP control systems with built-in

RFGWA gateways.

2. Requires Crestron CNXRMIRD IR Receiver, or CN-TVAV device controller.

3. The latest versions can be obtained from the Downloads | Software Updates section of the Crestron

website (www.crestron.com). Refer to NOTE after last footnote.

4. Crestron 2-Series control systems include the AV2 and PRO2. Consult the latest Crestron Product

Catalog for a complete list of 2-Series control systems.

5. CNX update files are required for either CNMSX-AV/PRO or CNRACKX/-DP. Filenames for CNX

update files have a UPZ extension and ST-CP files are in one EXE or zipped UPZ file. To avoid program

problems, make certain you are using the update file with the correct suffix letter (e.g., S, V, W, X).

NOTE: Crestron software and any files on the website are for Authorized Crestron

dealers only. New users may be required to register to obtain access to certain areas

of the site (including the FTP site).

WARNING: The WPR-48 is shipped from the factory partially assembled. That is,

the eight screws that secure the rear cover to the button faceplate are not fully

tightened to simplify the process of installing button labels, as described in

“Installing/Replacing Button Labels” on page 12. As such, the unit is not waterproof;

exposing it to water may result in damage to the equipment, possible personal injury,

and void the product warranty.

2 •Waterproof Wireless Handheld Remote: WPR-48 Operations Guide – DOC. 6254A

Crestron WPR-48 Waterproof Wireless Handheld Remote

Physical Description

The WPR-48 electronic hardware is housed in a slim, rubberized plastic, waterproof

enclosure, with two clear windows for large customized labels that identify the

intended button functions. (Refer to the illustration on the next page.)

Electroluminescent backlighting enhances the labeling and makes it possible to read

the button functions even in the dark.

WARNING:The WPR-48 Wireless Handheld Remote has been tested and found to

be waterproof when submerged to a maximum depth of 1 meter, for a maximum

duration of 30 minutes, per IEC 60529 IPX7 standards. Exceeding these limits may

result in damage to the equipment, possible personal injury, and void the product

warranty.

The unit is shipped with the lanyard foot installed. The lanyard foot puts the unit at a

convenient angle when the unit is placed on a flat surface; the lanyard makes it easy

to carry the unit around the home. A blank foot is supplied for those installations in

which the unit is usually left in one location.

Refer to “User-Printable Customized Button Labels” on page 10 for details about

creating button labels.

WPR-48 Waterproof Wireless Handheld Remote with Lanyard and Customized Button

Labels, Mounted in Docking Station

Operations Guide – DOC. 6254A Waterproof Wireless Handheld Remote: WPR-48 •3

Waterproof Wireless Handheld Remote Crestron WPR-48

WPR-48 Physical Views.

Connectors

The only connectors on the WPR-48 are the two contacts on the back panel. These

contacts are used for charging the long-life lithium-ion battery when the unit is

placed in the WPR-DS docking station. These contacts are also used when

configuring the unit and when firmware is uploaded via the docking station.

NOTE: During configuration and when firmware is being uploaded, the charging

circuits in the docking station are automatically disconnected.

Controls

The WPR-48 has nine three-position buttons, which can be configured, using the

Crestron Viewport, for 9-, 18-, 27-, or 48-function operation. Actual button functions

are defined in the SIMPL Windows program, based on the application of the unit

within the Cresnet system.

Indicators

The only indicators on the hand-held WPR-48 are the four LEDs on the face of the

unit, above the button function windows. The B LED (red) blinks if the battery

charge is low; the T LED (red) illuminates when the WPR-48 is transmitting. The

operation of the JLED (red) and the KLED (red) depends on the unit’s

configuration. In a 48-button configuration, the JLED indicates that the unit is

transmitting ‘page 1’ functions; the KLED indicates that the unit is transmitting

‘page 2’ functions. In the 9-, 18-, and 27-button configurations, there are no ‘page’

functions. If the configuration is set up to allow key presses to change the unit’s RF

or IR ID, these two LEDs illuminate simultaneously during ID reprogramming (refer

to “Setting RF/IR ID via Button Presses” on page 9 for details).

4 •Waterproof Wireless Handheld Remote: WPR-48 Operations Guide – DOC. 6254A

Crestron WPR-48 Waterproof Wireless Handheld Remote

Industry Compliance

As of the date of manufacture, this unit has been tested and found to comply with

specifications for CE marking and standards per EMC and Radiocommunications

Compliance Labelling (N11785).

NOTE: This device complies with part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. The equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Setup

Applying Power

Power for the WPR-48 is provided by the built-in, rechargeable 3.6 VDC lithium-ion

battery. (The unit is shipped with the battery charged.) The battery is recharged when

the WPR-48 is placed in the companion docking station (WPR-DS). Note that the

docking station is also used during configuration procedures and when uploading

new firmware to the WPR-48. When the docking station is being used for

configuration or firmware functions, the recharge circuits are automatically turned

off.

Configuring the WPR-48

The WPR-48 can be configured to transmit either RF or IR signals. (By default, the

units are shipped as RF devices.) Every WPR-48 transmitter communicating with a

Cresnet system via RF requires a unique RF ID to secure RF communications.

Similarly, every WPR-48 transmitter communicating with a Cresnet system via IR

signals requires a unique IR ID to secure IR communications. The unit’s default RF

Operations Guide – DOC. 6254A Waterproof Wireless Handheld Remote: WPR-48 •5

Waterproof Wireless Handheld Remote Crestron WPR-48

ID and IR ID settings are 10. The RF/IR ID of the unit and the RF/IR ID specified

for it in the SIMPL Windows program must match. There are 256 possible two-digit

hexadecimal codes ranging from 00 to FF.

Refer to the note on page 18 for a

definition of Viewport. To configure the WPR-48 through Viewport, the following items are required

• PC running Crestron’s Viewport utility, version 3.99.01 or later.

• An RS-232 cable (RJ-11 – DB-9) such as the Crestron STCP-502 (not

supplied) to connect the WPR-DS to the serial port of the PC. This

connection can also be made with a modular RJ-11 cable and a DB9F to

RJ-11 adapter. (Refer to the following illustration.)

NOTE: Check the SIMPL Windows gateway models prior to setting the RF ID or

IR ID. Some gateway models do not support ID “00” or “FF.”

NOTE: If the battery in the WPR-48 has become fully discharged, it will require

approximately five minutes of recharging before the unit can be reconfigured.

With the WPR-48 inserted in its docking station, complete the following procedures.

1. Verify that communications with the PC are established, as specified in

“Communication Settings” on page 18.

2. Open the Crestron Viewport, and from the menu bar, select Functions |

Configure WPR-48 as shown in the following illustration.

NOTE: While configuring the WPR-48, do not remove the WPR-48 from the

docking station until you have exited the dialog by clicking on Exit.

6 •Waterproof Wireless Handheld Remote: WPR-48 Operations Guide – DOC. 6254A

Indice

Altri manuali Crestron Telecomando universale

Crestron

Crestron infiNET EX MLX-2 Manuale utente

Manuali Telecomando universale popolari di altre marche

Pronto

Pronto Peel Manuale utente

GE 24929 Manuale utente

Radio Shack

Radio Shack Wireless Remote Control System Manuale utente

AUVIO

AUVIO Universal Home Theater Remote Manuale utente

Philips

Philips Icon SRU4106 Manuale utente

THOMSON

THOMSON ROC4309 Manuale utente

Philips

Philips pm625S Manuale utente

GE RM94931 Manuale utente

RCA

RCA RCU600WMS - Universal Remote Control Manuale utente

Blackweb

Blackweb BWB17AV002 Manuale utente

Marmitek

Marmitek DoorGuard 300 Manuale utente

Chunghop

Chunghop RM-L618 Manuale utente

GE RM24965 Manuale utente

Anderic

Anderic KTN828 Manuale utente

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuale utente

Medion

Medion E74023 Manuale utente

intensity

intensity RM02A Manuale utente

GE RM24950 Manuale utente