Crystal Vision ENDAC Manuale utente

Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England.

E-mail: [email protected] Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059

ENDAC

Encoding converter

ENDAC User Manual R1.03 Crystal Vision

126/02/2007

Contents

1 Introduction 3

1.1 Operating modes 4

Analogue video formats 4

Status and control 4

2 Hardware installation 5

2.1 Rear modules and signal I/O 5

Rear module connections with RM01 5

Module configuration 6

2.2 General Purpose Interface (GPI) 6

3 Card edge operation 10

3.1 Card edge switch settings 10

3.2 Reading card edge LEDs 11

3.3 Card edge configuration 11

Component output format 11

Line standard 11

Adding NTSC setup (pedestal) 12

Betacam format 12

Control 12

4 Using the active front panel 13

4.1 Module selected 13

The ENDAC menu structure 15

Home Menu 16

Input Menu 17

Output Menu 17

ENDAC User Manual R1.03 Crystal Vision

226/02/2007

5 Statesman 18

5.1 Installing Statesman 18

5.2 Statesman operation 19

Video properties 20

6 Trouble shooting. 21

6.1 Card edge monitoring 21

Status LEDs 21

6.2 Fault finding guide 21

7 Specification 23

Revision 2 Block diagram title corrected 20-02-07

Revision 3 Text in table on page 5 corrected 26-02-07

Crystal Vision Introduction

326/02/2007

1Introduction

ENDAC is a 12-bit broadcast encoder with four outputs that can be configured to give a

variety of component and composite signals.

ENDAC will fully integrate with any other interface or keying product from the Crystal

Vision range. Further flexibility is afforded by the large choice of control options. Control

options include board edge control, local or remote active control panel and the Statesman

PC Control System.

•12-bit digital encoder

•Flexible control, including PC software.

•Three link configurable outputs, 1 fixed composite output

•Compact design for high packing density

ENDAC 12-bit Encoder

ENDAC is a 100mm x 266mm module that fits in Crystal Vision four standard frame

sizes. 24 modules fit in 4U, 12 modules fit in 2U, six in 1U or two in a desktop box. There

are a range of rear connector modules available for the ENDAC which allow the system

builder great flexibility in frame configuration.

12-bit

digital

encoder

and

D to A

Output

configure

Y, G or composite

C, U, B or composite

V, R or composite

Composite

Reclocked

SDI Output

Reclocker

and

cable

equilizer

SDI Input

Crystal Vision Introduction

426/02/2007

1.1 Operating modes

Analogue video formats

There are four analogue video outputs of which one is a fixed composite output. The other

three video outputs can be configured using on-board links to produce a selection of

further composite outputs, YC, GBR or YUV component (Y’P’b P’r or Y’C’b C’r). 625

and 525-line output standard can be set. Data in the VBI (vertical blanking interval) is

passed to the analogue composite output. The addition of a 7.5% IRE setup is also

selectable when outputting an NTSC format signal. Betacam signal levels can also be

selected for component YUV outputs.

Status and control

Status and control is available using the board edge menu selection switches and LEDs.

Control and status reporting is also available from either an active frame front or remote

active control panel. PC control is also available using Crystal Visions Statesman PC

controller package.

Note. When the ENDAC is set to remote control mode the position of the board edge

switches may not reflect the actual configuration of the card. Returning the card to local

control will reinsert the board edge configuration

Crystal Vision Hardware installation

526/02/2007

2Hardware installation

The ENDAC single height module uses the RM01, which will fit into all Crystal Vision

rack frames. All modules can be plugged in and removed while the frame is powered

without damage.

The ENDAC can also be used with several other rear modules such as the RM02 and

RM18 but at reduced packing density.

2.1 Rear modules and signal I/O

The Indigo 4 4U frame will house up to 24 single height modules with up to three power

supplies. The FR2AV and Indigo 2 2U frames will house up to 12 single height modules

and dual power supplies. The FR1AV and Indigo 1 1U frames will house six single height

modules and a single power supply. The DTBAV and Indigo desk top boxes both have a

built-in power supply and will house up to two single height modules.

Note: For details of fitting rear connectors please refer to the appropriate frame manual

Rear module connections with RM01

The RM01being a single height module will allow maximum packing density with the

maximum number of outputs available.

RM01 rear module connector Description

RM01

•24 ENDAC modules per

Indigo 4 frame

•12 per FR2AV or Indigo

2 frame

•Six per FR1AV or Indigo

1 frame

•2 per Indigo DT

•All frame slots can be

used

BNC I/O assignment

R/V PAL/NTSC OUT Component R / V or composite output (link selectable)

SDI IN Serial digital input

SDI LOOP Reclocked SDI input loop-through

Y/ G PAL/NTSC OUT Component G / Y, YC-Y or composite output (link selectable)

C/B/U PAL/NTSC OUT Component B / U, YC-C or Composite output (link selectable)

PAL/NTSC OUT Composite Output

Crystal Vision Hardware installation

626/02/2007

Module configuration

The ENDAC has five user selectable jumper links, which are used to configure output

formats.

Note links PL10 & PL11 must be moved together as a pair.

Linked position Output Function

PL2 (YCY) Y

PL3 (CVBS) Composite

PL4 (G/Y)

Y/ G PAL/NTSC OUT

Green or Y component

PL5 (YCC) C

PL6 (CBVS) Composite

PL7 (B/U)

C/B/U PAL/NTSC OUT

Blue or U component

PL8 (CBVS) Composite

PL9 (R/V) R/V PAL/NTSC OUT Red or V component

PL10 (U) C/B/U PAL/NTSC OUT Left Y’P’bP’r

Right Y’C’bC’r

PL11 (V) R/V PAL/NTSC OUT Left Y’P’bP’r

Right Y’C’bC’r

2.2 General Purpose Interface (GPI)

Each frame slot has up to six connections ‘a-f ‘for GPI control and monitoring. These

connections are available at the rear of the frame on the 26-way D type Remote

connectors.

GPI Low (<1V) High (+5V)

0 ‘a’ No user connection at present

1 ‘b’ No user connection at present

2 ‘c’ Loss of input No user connection at present

3 ‘d’ No user connection at present

4 ‘e’ No user connection at present

5 ‘f’ No user connection at present

As supplied, each GPI output has a 220Ωresistor in series with its output. This allows for

an external LED to be driven, connected to a DC voltage of +5V.

Crystal Vision Hardware installation

726/02/2007

4U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of eight rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

3 8 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)

4 7 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)

5 5 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

6 4 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

7 5 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)

8 4 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)

9 3 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)

12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (5) 9 (5) 18 (5) 26 (5) 19 (6) 20 (6)

2 7 (5) 16 (5) 17 (5) 25 (5) 10 (6) 11 (6)

3 8 (7) 9 (7) 18 (7) 26 (7) 19 (8) 20 (8)

4 7 (7) 16 (7) 17 (7) 25 (7) 10 (8) 11 (8)

5 5 (5) 6 (5) 15 (5) 24 (5) 1 (6) 2 (6)

6 4 (5) 14 (5) 13 (5) 23 (5) 3 (6) 4 (6)

7 5 (7) 6 (7) 15 (7) 24 (7) 1 (8) 2 (8)

8 4 (7) 14 (7) 13 (7) 23 (7) 3 (8) 4 (8)

9 3 (5) 12 (5) 22 (5) 21 (5) 12 (6) 13 (6)

10 10 (5) 11 (5) 19 (5) 20 (5) 21 (6) 22 (6)

11 3 (7) 12 (7) 22 (7) 21 (7) 12 (8) 13 (8)

12 10 (7) 11 (7) 19 (7) 20 (7) 21 (8) 22 (8)

Table shows pin number (Remote number)

Note: Remote 1, Remote 3, Remote 5 and Remote 7 are 26 way high-density D-Type female

sockets. Frame ground is pin 2 and +5V @500mA is pin 1 in each case.

Remote 2, Remote 4, Remote 6 and Remote 8 are 26 way high-density D-Type male plugs

and frame ground is pin 6 in each case and +5V @500mA is pin 15 on Remote 2 and

Remote 6.

Note. The +5V output is protected by self-resetting thermal fuses, which limit the total

output current available from Remotes 1-4 to approximately 1A. Remotes 5-8 are similarly

protected.

UpperLower

Crystal Vision Hardware installation

826/02/2007

2U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of four rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

3 8 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)

4 7 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)

5 5 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

6 4 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

7 5 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)

8 4 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)

9 3 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)

12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)

Table shows pin number (remote number)

Note: Remote 1 and Remote 3 are 26 way high-density D-Type female sockets. Frame ground is

pin 2 and +5V @500mA is pin 1 in each case.

Remote 2 and Remote 4 are 26 way high-density D-Type male plugs and frame ground is

pin 6 in each case and +5V @500mA is pin 15 on Remote 2.

Note. The +5V output is protected by self-resetting thermal fuses, which limit the total

output current available from Remotes 1-4 to approximately 1A.

1U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of two rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

3 5 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

4 4 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

5 3 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

6 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

Table shows pin number (remote number)

Note: Remote 1: 26 way high-density D-Type female socket. Frame ground is pin 2 and +5V

@500mA is pin 1.

Remote 2: 26 way high-density D-Type male plugs and frame ground is pin 6 and +5V

@500mA is pin 15

Note. The +5V output is protected by self-resetting thermal fuses, which limit the total

output current available from Remotes 1-2 to approximately 1A.

Crystal Vision Hardware installation

926/02/2007

DTB-AV desk top box GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to the rear remote connector as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 1 2 3 4 5 6

2 9 10 11 12 13 14

Note: Remote connector is 15 way normal density D-Type socket. Frame ground is pin 15.

Indigo DT desk top box GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to the rear remote connector as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

Table shows pin number (remote number)

Note: Remote 1: 26 way high-density D-Type female socket. Frame ground is pin 2 and +5V

@500mA is pin 1.

Remote 2: 26 way high-density D-Type male plugs and frame ground is pin 6 and +5V

@500mA is pin 15

Note. The +5V output is protected by self-resetting thermal fuses, which limit the total

output current available from Remotes 1-2 to approximately 1A.

Indice

Altri manuali Crystal Vision Convertitore multimediale

Crystal Vision

Crystal Vision DDAA246 Manuale utente

Crystal Vision

Crystal Vision Indigo ADDEC-210 Manuale utente

Crystal Vision

Crystal Vision Dual 3G-DL Manuale utente

Crystal Vision

Crystal Vision Up-and-down-S Manuale utente

Crystal Vision

Crystal Vision Indigo ADCA412 Manuale utente

Crystal Vision

Crystal Vision Up-Down 3G Series Manuale utente

Crystal Vision

Crystal Vision Indigo Q-Down Manuale utente

Crystal Vision

Crystal Vision Dual DL-3G Manuale utente

Crystal Vision

Crystal Vision Indigo Q-Down Mini Manuale utente

Crystal Vision

Crystal Vision Up-and-down Manuale utente

Crystal Vision

Crystal Vision Indigo DACA214 Manuale utente

Crystal Vision

Crystal Vision DEC104S Manuale utente

Crystal Vision

Crystal Vision Indigo CoolFlow MON210 Manuale utente

Crystal Vision

Crystal Vision DEC101S Manuale utente

Crystal Vision

Crystal Vision ADC104 Manuale utente

Crystal Vision

Crystal Vision ADDEC-100 Manuale utente

Crystal Vision

Crystal Vision ARC102 Manuale utente

Crystal Vision

Crystal Vision ADDEC-200 Manuale utente

Crystal Vision

Crystal Vision UP-DOWN-VF Series Manuale utente

Crystal Vision

Crystal Vision Indigo Wallbox Q-Down Manuale utente

Crystal Vision

Crystal Vision Vision 3 Manuale utente

Crystal Vision

Crystal Vision DDAA132P Manuale utente

Crystal Vision

Crystal Vision ShARC-XP Manuale utente

Crystal Vision

Crystal Vision Indigo ALLDAC Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente