CS Instruments VA 520 Manuale utente

VA 520 English V1.06 Page 1 of 30

EN –English

Instruction manual

Consumption counter VA 520

with Display, 4 ... 20 mA and pulse output (galv. isolated)

Stationary

Flow and consumption measurement for compressed air and gases

VA 520 English V1.06 Page 2 of 30

I. Foreword

Dear customer,

thank you very much for deciding in favour of the VA 520. Please read this

installation and operation manual carefully before mounting and initiating the device

and follow our advice. A riskless operation and a correct functioning of the

VA 520 are only guaranteed in case of careful observation of the described

instructions and notes

Sales Office South / Geschäftsstelle Süd

Zindelsteiner Str. 15

D-78052 VS-Tannheim

Tel.: +49 (0) 7705 978 99 0

Fax: +49 (0) 7705 978 99 20

Mail: [email protected]

Web: http://www.cs-instruments.com

Sales Office North / Geschäftsstelle Nord

Am Oxer 28c

D-24955 Harrislee

Tel.: +49 (0) 461 700 20 25

Fax: +49 (0) 461 700 20 26

Mail: [email protected]

Web: http://www.cs-instruments.com

VA 520 English V1.06 Page 3 of 30

II. Table of Contents

I. Foreword ....................................................................................................................... 2

II. Table of Contents ...................................................................................................... 3

1Safety instructions........................................................................................................ 5

2Instruments description ............................................................................................... 6

3Technical data............................................................................................................... 7

4Installation Description ................................................................................................ 8

4.1 Displayhead Position............................................................................................................. 9

5Flow measuring ranges...............................................................................................10

5.1 Flow air.................................................................................................................................. 10

5.2 Flow for different gases....................................................................................................... 10

6Dimensions ..................................................................................................................11

6.1 With measurement section and screw-in thread.............................................................. 11

6.2 With measurement section and flange (Material stainless steel 1.4404):...................... 12

7Electrical wiring / Displayhead position.....................................................................13

7.1 Electrical wiring.................................................................................................................... 13

8Operation......................................................................................................................14

8.1 Initialization .......................................................................................................................... 14

8.2 Main menu ............................................................................................................................ 15

8.3 Settings................................................................................................................................. 15

8.3.1 Sensor Setup................................................................................................................... 16

8.3.1.1 Input / change tube diameter.................................................................................... 16

8.3.1.2 Input / change consumption counter........................................................................ 17

8.3.1.3 Definition of the units for flow, velocity, temperature and pressure ......................... 17

8.3.1.4 Definition of the reference conditions....................................................................... 18

8.3.1.5 Setting of Zeropoint and Low-flow cut off................................................................. 19

8.3.2 Modbus Setup.................................................................................................................. 20

8.3.2.1 Modbus Settings (2001…2005)............................................................................. 21

8.3.2.2 Values Register (1001 …1500) ................................................................................ 21

8.3.3 Pulse /Alarm..................................................................................................................... 23

8.3.3.1 Pulse output.............................................................................................................. 23

8.3.4 User Setup....................................................................................................................... 24

8.3.5 Advanced......................................................................................................................... 24

8.3.6 4 -20mA ........................................................................................................................... 25

8.3.7 VA 520 Info...................................................................................................................... 27

Inhaltsverzeichnis

VA 520 English V1.06 Page 4 of 30

9Maintenance.................................................................................................................28

10 Cleaning of the sensor head....................................................................................28

11 Re-Calibration...........................................................................................................28

12 Spare parts and repair..............................................................................................28

13 Calibration.................................................................................................................28

14 Warranty....................................................................................................................29

VA 520 English V1.06 Page 5 of 30

1Safety instructions

Please read carefully before starting the device!

Warning: Do not exceed the pressure range of 16 bar!

Observe the measuring range of the sensor!

Always observe the direction of flow when positioning the sensor!

The screwed fixture must be pressure tight.

It is absolutely necessary to avoid condensation on the sensor element or water drops in the

measuring air as they may cause faulty measuring results.

The manufacturer cannot be held liable for any damage which occurs as a result of non-

observance or non-compliance with these instructions. Should the device be tampered with

in any manner other than a procedure which is described and specified in the manual, the

warranty is cancelled and the manufacturer is exempt from liability.

The device is destined exclusively for the described application.

We offer no guarantee for the suitability for any other purpose and are not liable for errors

which may have slipped into this operation manual. We are also not liable for consequential

damage resulting from the delivery, capability or use of this device.

We offer you to take back the instruments of the instruments family VA 520 which you would

like to dispose of.

Qualified employees from the measurement and control technology branch should only carry

out adjustments and calibrations.

The consumption sensor VA 520 works according to the calorimetric measuring procedure.

Flammable gases

If this consumption sensor is used for measurement of flammable gases (e. g. natural gas

and so on) we expressly would like to point out that the sensor has no DVGW admission,

however, it can be used for measurements in natural gas. A DVGW admission is not

mandatory.

The consumption sensor corresponds with the current state of technology and basically it can be used

in any flammable and non-flammable gases.

If the sensor is used e.g. in the medium natural gas, the sensor will be adjusted for natural

gas. The calibration protocol (inspection certificate) will be included in the scope of delivery.

The area outside the pipeline (ambient area of the sensor) must not be an explosive area.

The installation has to be carried out by authorized professionals.

VA 520 English V1.06 Page 6 of 30

2Instruments description

The VA 520 is a compact consumption counter for compressed air and gases.

Special features:

- Optimum accuracy due to compact design

- Integrated in- and outlet section

- Less flow due to measuring section

- Integrated Display, Units free selectable. m³/h, m³/min, l/min, l/s, kg/h, kg/min, kg/s, cfm

- Modbus RTU (RS485) Interface

- Analogue output 4..20mA

- Pulse output galv. isolated.

CS Instruments Service Software

- Analogue output 4...20 mA scalable

- Selection of gas type (Air, Nitrogen, Argon, Nitrous oxide, CO2, Oxygen, Natural gas)

- Read out Service data

- Sensor diagnoses

VA 520 English V1.06 Page 7 of 30

3Technical data

Measurement: Flow and consumption

Standard settings ex works:

DIN 1945, ISO 1217 at 20°C and 1000 mbar

Selectable Units m³/h (Standard settings ex works)

m³/min, l/min, l/s, ft/min, cfm, m/s, kg/h, kg/min, kg/s

Measuring principle: calorimetric measurement

Sensor: Pt45, Pt1000

Measuring medium: Air, gases

Operating temperature: -30 ... 80°C

Operating pressure: up to 16 bar, special version PN 40 (40 bar)

Power supply: 18 to 36 VDC

Power consumption: max. 5W

Digital output: RS 485 (Modbus RTU)

Analog output: 4...20 mA (see table below),

max. burden < 500 Ohm

Description

Analogue output

VA 520 with integrated 1/4" meas. section

4… 20 mA =

0...90 l/min

VA 520 with integrated 1/2" meas. section

4… 20 mA =

0...90 m³/h

VA 520 with integrated 3/4" meas. section

4… 20 mA =

0...170 m³/h

VA 520 with integrated 1" meas. section

4… 20 mA =

0...290 m³/h

VA 520 with integrated 1 1/4" meas. section

4… 20 mA =

0...530 m³/h

VA 520 with integrated 1 1/2" meas. section

4… 20 mA =

0...730 m³/h

VA 520 with integrated 2" meas. section

4… 20 mA =

0…1195m³/h

VA 520 with integrated 2 1/2" meas. section

4… 20 mA =

0…2185m³/h

VA 520 with integrated 3" meas. section

4… 20 mA =

0…2910m³/h

Pulse output: pulse output potential free (dry contact)

passive: max. 48Vdc, 500mA

1 pulse pro m³ resp. pro l, Valency

adjustable with the display keys

Accuracy: ± 1,5 % m.v., ± 0,3 % f. s.*

Display: TFT 1.8 Resolution 220 x 176

Mounting thread: R 1/4", R1/2", R3/4", R1", R 1 1/4" R1 1/2", R 2” DIN EN

10226 (ISO 7-1)

Material: Stainless steel 1.4301 / 1.4404

Version with flange DIN EN 1092-1: Stainless steel 1.4404

‘* m.v. = measured values

f.s. = full scale

VA 520 English V1.06 Page 8 of 30

4Installation Description

The following table shows the required inlet sections depending on the existing disturbance / flow

disturbance.

Table of additionally required inlet sections

Flow obstruction in front of the

measuring section

Minimum length inlet

section (L1)

Minimum length

outlet section (L2)

Slight curve

(bend < 90°)

12 x D

5 x D

Reduction

(pipe narrows towards the meas. section)

15 x D

5 x D

Expansion

(pipe expands towards the meas. section)

15 x D

5 x D

90° bend

or T-piece

15 x D

5 x D

2 bends á 90°

on one level

20 x D

5 x D

2 bends á 90°

3-dimensional change of direction

35 x D

5 x D

Shut-off valve

45 x D

5 x D

15 x D 5 x D

15 x D 5 x D15 x D

15 x D 5 x D

20 x D 5 x D

35 x D 5 x D

5 x D45 x D

The respective minimum values required are indicated here. If it is not possible to observe the

stipulated equalising sections, considerable deviations in the measuring results must be expected.

Attention:

The measuring sections of VA 520 consumption counters with 1 1/2" and 2" measuring section

have reduced inlet and outlet sections. Please take into consideration the recommended inlet and

outlet sections. Dimension please see page 9 and 10.

VA 520 English V1.06 Page 9 of 30

4.1 Displayhead Position

The Position of the Displayhead is twistable by 180 e.g. in

case of reverse flow direction.

For this purpose the 6 fastening screws are to be released

and the displayhead rotated 180°.

Caution:

It must be ensured that the connection plugs are still plugged

and the gasket is installed correctly.

Fastening screws

VA 520 English V1.06 Page 10 of 30

5Flow measuring ranges

5.1 Flow air

Pipe size

Inner pipe

Pipe size

VA 520

Consumption

Inch

Meas. ranges from … to

Standard setting

1/4“

8,5

DN 8

0,8…90 l/min

1/2“

16,1

DN 15

0,2…90 m³/h

m³

3/4“

21,7

DN 20

0,3...170 m³/h

m³

1“

27,3

DN 25

0,5...290 m³/h

m³

1¼“

36,8

DN 32

0,7…530m³/h

m³

1 ½"

41,8

DN 40

1,0…730 m³/h

m³

2“

53,1

DN 50

2,0...1195 m³/h

m³

2 ½"

71,1

DN 65

4,0…2185 m³/h

m³

3“

81,9

DN 80

7,0…2910 m³/h

m³

Reference DIN 1945/ ISO 1217: 1000mbar /20°C; Air

5.2 Flow for different gases

1/4"

1/2"

3/4"

1 ¼"

1 ½"

2 ½"

Analog

output

20mA

Analog

output

20mA

Analog

output

20mA

Analog

output

20mA

Analog

output

20mA

Analog

output

20mA

Analog

output

20mA

Analog

output

20mA

Analog

output

20mA

l/min

[m³/h]

Reference DIN1945/ ISO 1217: 20°C, 1000 mbar (Reference during calibration)

Air

170

290

530

730

1195

2185

2910

Adjustment to DIN 1343: 0°C, 1013,25 mbar

Air

160

270

490

670

1100

2010

2675

Argon

140

275

460

830

1140

1870

3415

4555

Carbon dioxide

CO2

175

290

525

720

1185

2160

2880

Nitrogen

155

260

470

650

1060

1940

2590

Oxygen

165

280

505

695

1140

2080

2775

Nitrous oxide

N2O

170

285

520

715

1170

2140

2855

Natural gas

105

170

310

430

705

1290

1720

Other gases on request

Please note:

The consumption sensor corresponds with the current state of technology and basically it can be used

in any flammable and non-flammable gases.

If this consumption sensor is used for measurement of flammable gases (e.g. natural gas and so on)

we expressly would like to point out that the sensor has no DVGW admission, however, it can be used

for measurements in natural gas. A DVGW admission is not mandatory.

The area outside the pipeline (ambient area of the sensor) must not be an explosive area.

Altri manuali per VA 520

Indice

Altri manuali CS Instruments Banco cassa

CS Instruments

CS Instruments VA 520 Manuale utente

Manuali Banco cassa popolari di altre marche

Omron

Omron H7CL Series Manuale utente

FAAC

FAAC XTR B Manuale utente

Olympia

Olympia NC-350A Series Manuale utente

Evco

Evco EV7001 Manuale utente

Record

Record FlowControl Manuale utente

XIA

XIA UltraLo-1800 Manuale utente

Cashmaster

Cashmaster Sigma 105 Manuale utente

Agilent Technologies

Agilent Technologies 53151A Manuale utente

Cashmaster

Cashmaster Sigma 105 Manuale utente

Tellermate

Tellermate TY Manuale per l'uso e la cura

HYOSUNG

HYOSUNG MX-4000W Manuale utente

Cashmaster

Cashmaster Sigma 105 Manuale utente

CCE

CCE 3200 Manuale utente

HP 53150A Series Istruzioni operative

HYOSUNG

HYOSUNG 1800CE Manuale utente

MZ electronic

MZ electronic EV-040 Manuale utente

Delfield

Delfield Shelleysteel SCFM-50 Manuale utente

TSI Instruments

TSI Instruments AEROTRAK+ 7201 Manuale utente