CSM ICG360 Manuale utente

Note: This gyro is like no other - please read this manual fully before

installing and flying the gyro

To bring you a great gyro CSM simply threw away the rule book and started with a clean sheet. The result, the ICG360, is packed with

new concepts in gyro technology:-

•YawRateDemand

•FlightModes

•HeadingLock

•Built-inExponential

•Anti-driftTemperatureCalibration

•TwostagePowerSupplyregulation

•Flightmodetailoringvia(optional)PCinterfacecable/software

Introduction

If you are familiar with conventional tail rotor gyro systems it is important to understand how this gyro is

different in order to get the best out of it.

Conventional Gyro systems

In a conventional gyro the pilot applies a rudder command and, as the helicopter responds to the

command the gyro opposes the pilot's command. The yaw rate achieved in such a system depends on

the 'gain' of the gyro. The more gain the gyro has the lower the yaw rate that can be achieved. It is

common with such systems to have to reduce the gyro gain to achieve the required yaw rate for some

manoeuvres (this being accomplished with the gyro gain switch).

The ICG360

In designing the ICG360 we have adopted a 'Yaw Rate Demand' philosophy making the system a true

Yaw rate gyro. In this system the rudder command from the pilot is interpreted as a request to the gyro

to establish the desired yaw rate. The gyro drives the tail rotor servo as needed to obtain this yaw rate.

This means that the ICG360 makes full yaw rate available even at high gain settings. With this system

you can now use the rudder travel volume (ATV) and rudder rates facilities to set up the desired full-

stick yaw rate and the gyro gain switch now becomes a 'Flight Mode Switch' for the gyro. There is no

need for so called Pilot Authority Mixing - indeed you should not use pilot authority mixing with this gyro

Flight Modes

The ICG360 has two flight modes selectable by the transmitter gyro gain switch (or Auxiliary channel

switch). Note: A rotary knob or slider is not recommended as it is not possible to accurately and

repeatedly set the gain with these. The modes are:

Mode 0 (Standard Mode)

This mode gives flying characteristics that are similar to conventional systems.

Mode 1 (Heading Lock Mode)

This mode provides a much higher resistance to unwanted yawing movements than can be obtained

with a conventional gyro system. This mode has great advantages in the following situations:

1) For the beginner, where this mode makes it possible for him/her to almost ignore the tail rotor control

in the initial hovering phase, which is made even easier as this mode allows the tail trim to be set before

the helicopter leaves the ground. (see 'Trim Adjustment')

2) For cross-wind hovering manoeuvres where the natural tendency of the helicopter to weathercock into

wind needs to be resisted.

3) For backwards flight manoeuvres and general "3D" flying.

The Standard mode may be employed for basic forward flight where the natural tendency of the

helicopter to weathercock can be helpful, especially to the less experienced pilot.

The graph (Figure 1) shows the way in which the gyro gain channel provides both mode switching and

independent gain adjustment of the two modes. If the gyro gain channel pulse is longer than the centre

value (1.5ms) the gyro is in Standard mode while with the gain channel pulse shorter than 1.5ms the

gyro is in Heading Lock mode. The Travel Volume (ATV) settings for the two switch positions provide a

convenient way of adjusting the gyro gain for each mode from the transmitter. Increasing the ATV of the

gyro gain channel increases the gain for that mode. If it is being used with a basic radio system without

a suitable channel for controlling the gyro gain then the gyro will run as a single rate unit with gain

adjustable from the manual gain control on the unit itself. In this case the gyro defaults to the Standard

mode.

100%

1.5ms

1ms 2ms

Flight Mode 0Flight Mode 1

Gain channel pulse length

Gain

(Standard Mode)(Heading Hold Mode)

Increasing gain Increasing gain

First Switch Position

Increasing gain channel ATV Increasing gain channel ATV

Second Switch Position

Gyro

Figure 1. The Gyro gain channel acts as both gyro mode switch and gain control

Installation.

Siting of the gyro.

Axis of rotation

(keep this parallel with main shaft of helicopter)

Attach to helicopter using two of the self-adhesive foam strips provided

COMPUTER

AUX. INPUT

REVERSE

SERVO

Rx 1-4 IN

Figure 2. Mounting the gyro

The ICG 360 should be mounted in the helicopter with its axis of rotation (as marked on the gyro case)

accurately parallel to the main shaft of the helicopter. The gyro sensor (together with the electronics of

the gyro) is anti-vibration mounted inside the gyro case. However, to provide further vibration and shock

resistance it is important that the gyro be mounted to the airframe using two of the double sided

adhesive foam strips provided. Do not use any other type of mounting foam as this will reduce the

performance of your gyro. Replacement strips are available as a CSM spare. The gyro case may be

aligned along or transverse to the length of the helicopter. For good adhesion, ensure that the surface to

which the gyro is attached is smooth, hard and clean. As with all high performance solid state gyro

systems, the ICG360 performs best if sited at a point of low vibration in the helicopter airframe. Where

possible avoid siting the gyro at the extreme front of the radio tray for example as this area is often

subject to high levels of main rotor generated vibration. Note: Tests suggest that the X-Cell plastic radio

tray may be too flexible and that better performance can be gained by mounting the gyro at the rear of

the frames.

Connecting to your radio system.

The ICG360 is designed to work with the following radio control systems:-

•FutabaPPM

•FutabaPCM1024

•JRPPM

•JRZPCM

•JRSPCM

If you wish to use this gyro with other types of radio system please contact CSM for advice.

Connect the gyro to your receiver as indicated in the following table:-

Radio

Type

Gyro "Rx1-4 IN"

connect to

Gyro "AUX INPUT"

connect to

Futaba PPM

Futaba PCM

JR PPM

JR ZPCM

JR SPCM

Channel 4 Channel 5

"Rudd"

"Aux2" or "Aux3"

"Aux2"

"Aux2" or "Aux3"

JR ZPCM pulse timing prevents the use of Aux 3 as gyro gain channel

** See setup notes for JR X388/3810/8103

Connect the "SERVO" output to the tail rotor servo.

Leave the "COMPUTER" connector unconnected. (This is for use with the optional PC interface

cable/software). Do not connect any form of extension to this connector.

If you are using a radio system (e.g. a 4 channel aero set) that does not have a channel that can be

allocated to the gyro gain/mode then the "Aux" input to the gyro should be left unconnected. In this case

the gyro will default to the Standard mode with the gain adjusted by the rotary gain control (near to the

"gyro set" light on the front panel of the gyro). Initially set the gain control to its mid position. Final

adjustment will require flight testing.

Futaba 9ZHP/ZAP

On these transmitters it is important to ensure that in all flight modes the gyro sense mode is set to

INHIBIT (see the "GYR" entry of the "helicopter condition" menu). Check under the "PMX" entry that no

throttle to rudder or rudder to gyro mixing is active in any of the flight conditions. Check in the "P->R"

entry that pitch to rudder mixing is inhibited. Under the "model" menu use the "FNC" entry to allocate

the gyro control to a switch of your choice.

JR PCM10S/SX

On these radios it is easier to disable the JR 'code 44' (gyro sense adjust) and control the gyro gain by a

switch, but if the ability to automatically switch between both gyro modes by the use of the flight mode

switch (idle up) is required, then the JR gyro sensing (code 44) should be used. Because the ICG360

gain control works from the centre of the channel outwards, an LCD value of 50% (the channel centre) is

in reality zero gain. Increasing the value will increase the gain in one flight mode, the other mode is

adjusted by decreasing the value below 50%: be aware that this value will be reversed so that an LCD

value of 25% will actually be a higher gain value than a LCD value of 30%. Note: if the gyro is adjusted

through the JR gyro software, the gyro channel ATV's/TA should be set to default values (100%).

JR X388S/X3810/X8103

On these radios it is easier to control the gyro gain through the gear channel as it is not always possible

to have control over other channels on a 2 position switch. Note: if so desired it is possible to set the

gyro up using the JR gyro software on the 3810/8103, see the PCM10 instructions above.

Reversing link

As with any gyro it is vital to ensure that it operates in the correct sense. Failure to do this will cause

an uncontrollable pirouette on take-off and beginners who are in any doubt on this aspect of the

set-up should seek advice. First establish that the sense of the transmitter control is correct (i.e. that

the application of a right rudder command causes a change in tail pitch that will rotate the helicopter to

the right). Once this has been done check that turning the helicopter to the left makes the gyro apply a

tail rotor command to the right. Should the gyro operate in the wrong sense use the gyro "REVERSE"

link to correct it. The gyro is supplied with the reversing link already fitted and to remove it simply pull

on its protruding tab and store it safely. When replacing the reversing link ensure that it is fitted over

both pins and pushed firmly into full engagement.

Initial Radio set-up

For initial flights we suggest that you adjust the radio system as follows:

ATS (Automatic Tail Stabilisation): OFF

Pilot Authority Mixing: OFF (this should never be used with the ICG360)

Rudder channel ATV (both directions): 50%

Gyro gain channel ATV (both directions): 50%

Mechanical

The ICG360 will work with any servo in the Futaba or JR ranges but as with any gyro system a fast

servo (e.g. Futaba FP-S9203 or JR 2700G) will give the best results.

To prevent damage due to excessive servo travel the servo movement is limited by the gyro

electronics. (Under no conditions will the servo travel past the electronic limit set by the gyro, regardless

of any increase in the ATV value.) You should use the longest servo arm that gives full movement of

the tail rotor pitch linkage without causing the linkage to bind or the servo to become stalled at

either extreme of travel.

Attention to the tail control linkage is important to getting the best from this gyro. You should aim for a

easy-moving but slop-free linkage between the tail servo and the tail blades. Inspect the bearings/thrust

races in the tail hub for smoothness of operation. Check the pitch slider and ball links for slop and

replace if needed. Some helicopters that have noticeable 'give' in the tail linkage may benefit from the

addition of a rear-mounted tail servo and rigid pushrod.

Remember that, during aerobatic manoeuvres, the combination of a high performance gyro and a fast

tail servo can place very high loads on the tail rotor drive train. Regularly Inspect tail rotor gears, etc. to

ensure that they are in good condition.

Batteries, power consumption, and wiring

Although the power consumption of the gyro unit itself is very modest, as with all high performance Solid

State gyro systems the speed of the gyro response will work the tail rotor servo harder than slower

mechanical gyro systems. Especially where a high performance servo is being used the battery drain

from the tail rotor servo can be high. We recommend that you use a good quality battery state

monitor and check it carefully before each flight.

Your receiver battery is a vital part of your tail rotor system. Remember that a battery in a low state of

charge or an old battery which has developed a high internal resistance will adversely affect servo

performance and may even cause the tail to wag on an otherwise well set up helicopter. You may wish

to consider maintaining the charge in your receiver battery between flights by the use of a quality Delta

Peak type field charger. In installing the gyro also bear in mind that voltage drops down long servo

extension leads will also detract from servo performance. Where the installation requires extensions to

be used (either between the receiver and gyro or between the gyro and the servo) avoid using ones that

are unnecessarily long.

Trim adjustment

Initially zero the rudder trim and any rudder sub-trim that your transmitter may have. Next, identify which

gyro gain switch position gives you Standard mode and which gives you Heading Lock mode. This can

be seen from the difference in the tail rotor servo behaviour on the ground. In Standard mode the rudder

servo will return to the neutral position when any rudder command is released, while in heading lock

mode the servo will tend to remain at or near its travel limit when a full stick rudder command is applied

and then removed. Now set the rudder trim so that with the gyro in Heading Lock mode the servo, once

centred, has no marked tendency to creep in either direction (though some slow residual creep of the

servo is quite normal). Once this trim position has been found no further adjustment of the transmitter

trim should be needed. However, slight adjustment of the helicopter tail control linkage may be needed

in order to remove any offsets in the Standard mode. This can only be done by flight trials.

Behaviour on the ground

For those used to conventional gyro systems the behaviour of the ICG360 on the ground may seem

unusual.

Unlike conventional systems, it is quite normal for the ICG360 in Standard mode to provide full tail rotor

servo movement for rudder commands that are as little as 30% of the full stick movement. This is a

consequence of the Yaw rate demand feature.

With the helicopter on the ground and the ICG 360 set in Heading Lock mode it is quite normal for the

tail rotor servo to slowly creep and may over the course of say 15 seconds creep to full travel. Your

transmitter rudder trim will affect the direction and speed of this creep but even after the trim has been

adjusted to minimise this some slow movement is still to be expected. This apparently strange

behaviour is caused by the stationary helicopter not responding to the heading corrections requested by

the gyro. In the absence of a response from the helicopter the gyro continues to increase the servo

command in an attempt to get the helicopter to obey. In flight the helicopter will, of course, respond to

the tail servo movements and the system act normally.

Trouble shooting

If the gyro does not respond as expected to any adjustment of the ATV, it may be helpful to plug a spare

servo directly into the appropriate RX channel as a check to make sure that the radio is driving the

channel as required, and that no other switches, mixers or other functions are interfering with the

operation of the channel.

Flying the gyro

Turn-on sequence

1. Turn on your transmitter

2. With the model stationary on the ground turn on your receiver.

3. Wait for about 7.5 seconds keeping the model still while the gyro goes through its self test.

4. Observe that the gyro set light comes on (or if this is inaccessible in your model move the rudder stick

full travel in both directions and ensure that the tail rotor servo responds to the stick movements)

5. Your ICG360 is now ready for flight.

If the set light fails to come on or flashes turn off the receiver for a few seconds and repeat the turn on

sequence.

!! Make sure the model is not moved during the gyro self test period. !!

Initial flight trials and setting up.

First select flight mode 1 (Heading hold mode) and hover the helicopter. Use short small 'stabs' of

rudder control to disturb the helicopter in yaw and observe. If some tendency to oscillate is seen, slightly

reduce the gyro gain. Conversely if no tendency to oscillate is seen try increasing the gain. You are

looking at this stage for the highest gain that gives no sign of oscillation when the tail is disturbed by

sudden changes in tail command. Observe any trim offset in the tail and correct this with the transmitter

rudder trim.

Now switch to Flight mode 0 (Standard mode) and repeat the exercise but in this case any trim offset

should be removed not by use of the transmitter trims but by adjusting the tail rotor linkage.

Once this has been done you may wish to check for tail wagging in fast forward flight. Should this be

observed, you may wish to lower the gyro gain slightly. Caution should be exercised over the use of the

heading hold mode in flying circuits or other general flying until you are familiar with the very special

handling characteristics this mode gives.

Adjusting the stick response

After initial setting use the rudder ATV, Rates, and Exponential facilities of the transmitter to tailor the

control response as required. Beware that the maximum yaw rate available (at any gain) is very

high. If an increase in available yaw rate is required increase the rudder travel on your transmitter

gradually until the desired response is obtained. Remember that increasing the ATV/TA will not

increase the overall tail throw.

The ICG360 has built-in exponential. You may find the following graph of yaw rate against rudder

command useful in deciding on the setting of rudder rates and rudder ATV. Remember that the ATV and

rates facilities work together so that setting the rudder ATV to 80% in both directions and also setting a

rudder rate of 60% will give a total rudder throw of 0.8 x 0.6 = 0.48 = 48%

100%20% 40% 60% 80%

200

400

600

800

1000

1200

1400

1600

Rotation rate (Deg./s)

Rudder signal (as % of standard 1 to 2ms deviation)

Figure 3. The built-in Exponential of the ICG360 gives this response to rudder control

Automatic Tail Stabilisation (ATS)

In Heading Lock mode the ICG360 requires NO ATS. Use of ATS in this mode will give unwanted

heading changes. Similarly, no Throttle-to-Tail Rotor mixing should be used in this mode. In Standard

mode you may find very small amounts of ATS or Throttle-to-Tail Rotor mixing useful.

Pilot Authority Mixing

This should not be used with the ICG360 gyro.

Tail rotor dynamics

To realise the full benefit of the ICG360 it is important to have a basic understanding of the dynamics of

the tail rotor system. It is a common misbelief that the higher the electronic gyro gain is, the better the

system will work. Whilst this is generally true, the electronic gain is only one part of the tail rotor system

and of equal importance is the amount of tail pitch range available, and the tail rotor disk size. The disk

size is also related to the tail rotor speed. Of course there are other influences on the tail system but

these are the most important and can be grouped together as mechanical gain.

If the mechanical gain is not correct, then the gyro will not be able to function to its best ability. For this

reason it is important to select the correct size servo arm that will give maximum tail pitch movement

without stalling the servo. Note: once this has been setup, increasing the rudder channel ATV/TA will not

increase the servo throw as this is limited electronically by the gyro. The rudder ATV/TA is used instead

to adjust the rotation rate.

Tail blade size

The correct length of tail blade can only be selected by flight testing. There are 2 types of test to

ascertain the correct size:

1) With the model in the hover at its normal flight rpm, making sure the gyro is in heading hold mode,

make a rapid vertical climb for 50 to 60 feet: there should be no discernible rotation of the model. If the

tail does not maintain its position this is a good indication that the diameter is too small. Note: if the

model is over pitched and there is a noticeable drop in rotor rpm during the climbout, then this will

invalidate the test as the tail would probably not be able to cope with this situation regardless of the

setup.

2) This test is only really necessary for those who wish to do advanced aerobatics/3D flying and should

only be carried out those who are confident to do so. With the model at a safe height fly the model

sideways, starting slowly and building up speed until it reaches its maximum possible speed:

a)If the tail manages to hold its position then the blade length is OK.

b)If the tail starts to lag behind, then either more pitch is needed (if the mechanical limits haven't

already been reached) or longer tail blades.

c) If the tail swings round suddenly and cannot return to the correct position then the tail rotor is stalling

and longer tail blades are needed.

Maximising Performance for Advanced 3D/Aerobatic Flight - by Bob Johnston

To get the maximum performance from this or any piezo gyro it is essential to minimise the vibration

reaching the gyro sensor. Apart from the obvious balance checks, make sure that the canopy, fins,

tuned pipe or muffler are not too loosely mounted, especially if the gyro is being used with a fast servo,

as it is possible for a resonance to build up which shows as a very fast shake, visible in the canopy and

tail.

If you feel confident to do so, try slowly tumbling the model while checking for any visible vibration, a

small amount is almost inevitable, but try to dampen any large vibrations present. Alternatively tumble

or roll the model at a safe height and if the gyro can be made to wag through the manoeuvre this is a

good indication that a component is resonating.

To set the maximum gain permissable for aerobatic flight, either a) fly the model as fast as possible in

a straight line and twitch the rudder stick a small amount, if this causes the gyro to wag, lower the gain

and repeat the test until the tail cannot be made to wag anymore. Obviously if the model cannot be

made to wag initially, keep increasing the gain until it does, and then reduce the gain a few percent.

Setting the gyro this way should prove sufficient for all flying except in very windy turbulent conditions

where the gain may have to be lowered by a few percent. b) Alternatively, if you feel confident enough

in your ability and your models reliability, put the model in a vertical dive for 3 or 4 hundred feet (90 to

120 metres) with the main rotor pitch at zero. Once terminal velocity has been reached, pull the model

out in a smooth arc, and if the model does not wag under these conditions it is unlikely to do so under

any conditions.

WARNING: Only attempt to carry out these flight tests if you are 100% confident in your own

flying ability, and the structural integrity of your equipment.

Boom supports

Tests have shown that the use of boom supports significantly increase the rigidity of the tail boom and

so allow a higher gyro gain to be used. Generally the longer the boom supports the better they will work.

Note: A loose/cracked boom support or a loose/cracked boom support clamp can have a significant

effect on the gyro gain.

Temperature stability

Although the gyro is temperature calibrated small temperature differences between the piezo sensor and

the temperature sensor occur from internal heating of the piezo sensor. These may cause a small trim

change during the first two minutes of operation. It is best to avoid flying the model immediately after

exposure to sudden temperature changes such as removing it from a cool car to a very hot flying site.

Humidity

Under conditions of extremely high humidity it is possible for condensation to form on the piezo sensor.

Formation and evaporation of this condensation will cause a shift in the gyro trim. Where it is not

possible to avoid subjecting to the gyro to such humidity levels it is advisable to leave the model

standing for a few minutes with the radio switched on so that the internal heating of the sensor disperses

the condensation. Having done so, cycle the receiver power to reset the gyro. Always protect the gyro

from ingress of water (e.g. rain).

PC interfacing

Your ICG360 is equipped with a 'COMPUTER' port which is provided for the experienced pilot wishing to

optimise the internal settings of the ICG360's two flight modes to their helicopter and flying style. An

optional Interface cable and software disk is available for use with this port. The interface/software is

compatible with any IBM PC compatible with a parallel (printer) port and VGA graphics. Comprehensive

additional instructions on the use of the PC interface are supplied with the software. Connection to the

'COMPUTER' port of the ICG360 must only be made via the correct optional interface cable.

No other form of connection to this port should be made as mis-use of this facility may damage the gyro

unit.

Ratings

Weight: 40g

Dimensions : 42.5mm High x 26.5mm Wide x 46.5mm Long

(excluding cables and mounting ears)

Power Supply: 3.5 to 7.2v

Repairs & Servicing

For repairs and servicing only, please contact:-

Westbury Products

Armour House

Brunswick Square

Southampton

Hants

SO14 1AR (Fax 01 703 335 463)

Manufactured in the UK by:

CSMDesignConsultancyLtd

8LittlebrookClose

Hadfield

Hyde

Cheshire

SK148AW(Fax:01619295984)

Distributed world-wide by:-

J.Perkins(Distribution)Ltd

90-96GreenwichHighRoad

LondonSE108JE

(Tel:01816922451

Fax:01816922469)

DOs and DON'Ts

DOs:

Do mount the gyro with its axis of rotation parallel to the helicopter main shaft.

Do mount the gyro on two of the supplied self-adhesive foam strips.

Do mount the gyro to a hard, smooth clean surface.

Do use the rudder ATV and rates to tailor required stick response.

Do check the sense of the gyro operation and fit/remove Reversing link as needed before flight.

Do use a battery state monitor and check it before each flight.

Do remove slop and stiffness from tail control linkage.

Do inspect tail gears etc. for wear.

Do explore the performance limits of this gyro with care.

DON'Ts:

Don't mount the gyro where it will be subjected to high vibration levels.

Don't use Pilot Authority Mixing.

Don't use ATS or Throttle-Tail mixing with the Heading Lock mode.

Don't use unnecessarily long servo extension leads with the gyro.

Don't use Aux3 as gain channel with JR ZPCM receivers

Don't connect a servo extension to the "COMPUTER" port of the gyro.

Don't move the model during gyro self-test time.

Indice

Altri manuali CSM Accessori

CSM

CSM ICG 180 Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente