CUSTERS CR 700 Manuale per l'uso e la cura

Custers Hydraulica B.V. Venray NL

ASSEMBLY AND USER MANUAL

CUSTERS® mobile scaffold

tower

CR 700 & 1300 AND HANDY 700 & 1300

in accordance with EN1004

maximum load: 200 kg/m2

maximum platform height:12 metres inside

8 metres outside

9505200001NLS March 2020 SAFE GUARD

CUSTERS HYDRAULICA B.V.

Smakterweg 33 5804 AE VENRAY NL Telephone : +31 (0) 478 55 30 00

P.O. Box 22 5800 AA VENRAY NL Fax : +31 (0) 478 55 30 10

Email info@custers.nl Website : www.custers.nl

 Custers Hydraulica B.V. Venray NL 
26-mrt-20 www.custers.nl 
 
 
CONTENTS 
 
 
1INTRODUCTION ...........................................................................3 
2WARRANTY AND LIABILITY .........................................................4 
3MARKING OF MOBILE SCAFFOLD TOWER COMPONENTS...............4 
4INSPECTION UPON DELIVERY ......................................................4 
5SAFETY INSTRUCTIONS ...............................................................5 
5.1 Check before assembly .........................................................................................5 
5.2 Personal protection and aids...............................................................................5 
5.3 Assembly ....................................................................................................................5 
5.3 Liifting up components..........................................................................................6 
5.4 Outriggers and expansion arches .....................................................................7 
5.5 Leading guardrails and guardrail frames .......................................................9 
6ASSEMBLING THE WIDE MOBILE SCAFFOLD TOWER 
(2,4,6,8,10,12 M).............................................................................10 
7 ASSEMBLING THE WIDE MOBILE SCAFFOLD TOWER (3,5,7,9,11 
M) 15 
8ASSEMBLING THE NARROW MOBILE SCAFFOLD TOWER 
(2,4,6,8,10,12 M).............................................................................20 
9ASSEMBLING THE NARROW MOBILE SCAFFOLD TOWER 
(3,5,7,9,11 M)..................................................................................25 
10 USING THE MOBILE SCAFFOLD TOWER ....................................30 
11 RELOCATING THE MOBILE SCAFFOLD TOWER ..........................31 
12 ANCHORAGES............................................................................32 
13 DISMANTLING OF THE MOBILE SCAFFOLD TOWER ...................32 
14 MAINTENANCE OF THE MOBILE SCAFFOLD TOWER ..................32 
15 GUIDELINES FOR USE, TRANSPORT AND STORAGE ...................33 
16 PARTS .......................................................................................34 
16.1 Parts list (wide mobile scaffold tower)..........................................................34 
16.2 Parts list (narrow mobile scaffold tower).....................................................35 
16.3 Composition tables ...............................................................................................36 
 
 
 
 
 
 
 
Custers Hydraulica B.V, Venray, the Netherlands. 
No part of this publication may be reproduced and/or published by means of, photocopy / 
print / microfilm / CD / DVD / Internet or any other means, without the express prior 
permission of the publisher Custers Hydraulica B.V. 

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

1 INTRODUCTION

The Custers® mobile scaffold tower is part of a wide range aluminium scaffold variants.

The Custers® mobile scaffold tower, if assembled according to this manual, complies with the

standard EN1004.

The Custers® mobile scaffold tower is available in the following versions:

- Scaffold length: 1.8 m and 2.5 m

- Scaffold width: 1.3 m and 0.7 m

This manual is intended to instruct you step by step how to assemble your scaffold easily and

safely. Incorrect assembly may result in serious personal injury. Read the safety instructions

carefully before assembly. The erection and dismantling should be done by experienced and

competent persons only.

The user is responsible for having this manual at hand at the place where the mobile

scaffold tower is being assembled and used, as well as with the person who

supervises the work.

If there are any uncertainties with regard to this manual, please contact your supplier and/or

producer.

Producer:

Custers Hydraulica B.V.

Smakterweg 33

5804 AE Venray The Netherlands

Telephone: +31 (0) 478 553 000

Telefax: +31 (0) 478 553 010

Email address: info@custers.nl

Website: www.custers.nl

Supplier:

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

2 WARRANTY AND LIABILITY

Custers warrants material and manufacturing defects for 12 months after delivery. The

warranty means that we repair faults at our own expense or - at our sole discretion –

will take back all or part of the delivered goods and replace them with a new delivery.

If we replace products delivered in fulfilment of our warranty obligation, the replaced

products become our property. All costs arising from the aforementioned obligation shall

be borne by the commissioning party. If products are provided for processing, repa ir,

etc., a warranty will only be given for the adequacy of the execution of the operations

that have been assigned.

Our liability does not apply:

a. If the faults are the result of improper use or any other

causes not involving material or manufacturing defects;

b. If the cause of the defects cannot be clearly demonstrated;

c. If all instructions for the use of the products, including the guidelines as indicated

in this manual, have not been strictly and completely observed.

The manufacturer’s liability does not apply if the buyer, on his own initiative, makes or

arranges for changes and/or repairs to the delivered products.

3 Marking of mobile scaffold tower components

- each aluminium / plastic component from the mobile scaffold tower is provided with the

Custers’ company name and a two-digit code corresponding to the year of production.

-8-rung frames are always provided with a compulsory waterproof label with details

of the scaffolding class and assembly instructions.

4 INSPECTION UPON DELIVERY

Upon receipt, check that the tower scaffolding is complete and undamaged.

Contact your supplier immediately if you notice that the components of the tower

scaffolding are damaged or if the components that have been delivered are incomplete.

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

5 SAFETY INSTRUCTIONS

5.1 Check before assembly

Verify whether the technicians are sufficiently qualified and that the place where the tower

scaffolding is to be erected is safe and suitable.

Caution:

- The ground must be sufficiently load-bearing and flat;

- The space must be free of obstacles, both on the ground and above ground;

- Verify whether the wind conditions are such that the scaffolding can be used;

- Check to make sure that you have all the components at the workplace;

- Never use damaged, incorrect or non-original components.

5.2 Personal protection and aids

- Always wear work gloves, safety shoes and a safety helmet.

- A sturdy rope, for the manually lifting of components or tools

- It is not allowed to mount fall protection equipment to the scaffold.

(If fall protection equipment must be used, use the existent façade or any other solid

construction.)

5.3 Assembly

The assembly of the mobile scaffold tower is described in the assembly instructions and must

be carried out by at least 2 persons. Use leading guardrail frames during the assembly to

prevent persons from falling.

The mobile scaffold tower must be erected flat with a maximum inclination of 1% (a maximum

of 1 cm inclination over a length of 1 metre); check this with a spirit level; correction is possible

by tightening the spindle nuts of the casters. The casters must always be in locked position,

except for relocating the scaffold. Make sure that the casters are locked, either by tightening

the wing nut, or by tilting the locking tab over the cantilevered edge of the chord stiffener.

The platforms must be secured by sliding the pawl of the blow-away protection under the

rung. The frames must be secured against each other using locking pins.

Horizontal ledgers/guardrails must preferably be positioned on the uprights in such a way

that the openings of the claws point outwards.

There must always be at least 1 platform with hatch on the working level; the working level

must be fitted with: guardrail, knee railing and toe boards all around. There must always be

at least one platform with a hatch on the resting level. The resting level must be fitted all

around with guardrails and knee railings and must be installed at a height of 2 metres.

A resting level is converted into a working level through the installation of toe boards all around.

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

5.3 Lifting up components

Lifting up components onto higher areas should be done by passing the components from

platform to platform. Parts can also be lifted upwards with a sturdy rope. Use a proper knot,

loop or hook to secure the components. Hoisting equipment may not be attached to the

scaffold.

Fig. 1

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

5.4 Outriggers and expansion arches

The outriggers/expansion arches specified in the table must always be fitted once the lower

edge of the scaffold has been erected. During assembly, the upper sides of the

outriggers/expansion arches must be connected to the underside of the rungs in order to

prevent them from sliding upwards unintentionally.

The basic form to be used, i.e. the arch to be used (small or large), can be read in the

composition tables.

The basic forms shown below must be strictly adhered to!

If the designated form is different, ballast weights may be required; please contact the

manufacturer/supplier for this. Small arches may be replaced by small legs and large arches

by large legs, provided that the use of legs follows the same basic form as the arches. This

means that the outriggers when viewed from the top, must be mounted in the same position

as the expansion arches.

Fig.2

Basic forms

A: Small arch, length 1300 mm B: large arch, length 2000 mm

C: Small arch, length 1300 mm D: large arch, length 2000 mm

1: Brace, length 2500 mm, art. nr. 9501.200.030CR

2: Brace, length 1913 mm, art. nr. 9501.200.048CR

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

If the mobile scaffold tower is placed against a wall, do not remove the outrigger/arch, but

turn it parallel to the wall. If the mobile scaffold tower is placed at an angle, remove the inner

outrigger/arch, and turn the outer two parallel to the wall.

expansion arch

option: brace

outrigger

Fig.3

Fig.4

Fig.5

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

5.5 Leading guardrails and guardrail frames

In order to prevent falls during assembly and dismantling of the mobile scaffold tower,

leading guardrails or guardrail frames must be used. The basic principle here is that the

edge protection, consisting of at least one guardrail, is fitted before entering the platform.

Custers Safe Guard leading guardrail frames:

- are used in the scaffolding from floor height of 2m rather than separate horizontal

ledgers and diagonal ledgers;

- provide protection against falling, before entering the platform through the hatch;

- are fitted and removed from a secure place;

- are easy to handle and easy to apply.

During the assembly phase of the mobile scaffold tower, the Safe Guard guardrail

frames must be used as follows (complete assembly sequence, see relevant sections):

Place the two Safe Guard guardrail frames (with the claws falling over the rungs) from the

standing surface. Make sure that the claws fall properly over the rungs and click the

diagonal ledgers in place.

Fig.6

Fig.7

Custers Hydraulica B.V. Venray NL

26-mrt-20 www.custers.nl

6 ASSEMBLING THE WIDE MOBILE SCAFFOLD TOWER

(2,4,6,8,10,12 m)

Fig.8

1: Insert both casters into the 4-rung

frame; and make sure that the

casters are properly secured;

2: Place the horizontal ledgers on the

uprights of the frame;

Fig.9

3: Insert both casters into the 4-rung

frame; and make sure that the

casters are properly secured;

4: Place the horizontal ledgers and the

horizontal/diagonal on the

uprights of the frame;

Fig.10

5: Place both 8-rung frames;

6: Place locking pins between the

frames themselves;

7: Place both diagonal ledgers;

8: Place both Safe Guards on

the upper rung: one on the

façade side, the other middle one

on the upper rungs. Click the diagonal

ledgers in place on the 5th rung of the

frame in question;

Altri manuali per CR 700

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali CUSTERS Scrivania

CUSTERS

CUSTERS HANDY Manuale utente

Manuali Scrivania popolari di altre marche

HP m9060n - Pavilion - Elite Scheda tecnica

Asus

Asus E210 Series Manuale utente

Dell

Dell Inspiron 600m Manuale utente

Dell

Dell Inspiron 3662 Manuale utente

TotalFlow

TotalFlow uFLO Manuale utente

HP Presario SV7000 - Desktop PC Manuale utente

HP ProDesk 400 G5 Manuale

Logitech

Logitech MK320 Manuale utente

Dell

Dell XPS 730 H2C Manuale utente

Sony

Sony Vaio Series Manuale utente

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuale utente

Alto

Alto MD 250 Manuale utente

Lenovo

Lenovo ThinkCentre Edge 72 Manuale

Lenovo

Lenovo ThinkStation D20 Manuale

Arbor Technology

Arbor Technology FPC-7800 Series Manuale utente

Sony

Sony VAIO VGX-TP1 Series Manuale utente

Asus

Asus Eee Box B204 Manuale utente

Dell

Dell Optiplex 9010 All In One Manuale utente