CutSteady CPT30004 Manuale utente

CutSteady U.S.A.

CutSteady

™

CutSteady

™

Gulf Industrial Solutions

ANGLE GRINDER

МАШИНА ШЛИФОВАЛЬНАЯ УГЛОВАЯ

CPT30004

CutSteady U.S.A.

™

CutSteady U.S.A.

™

CutSteady

™

CutSteady

™

5 5 5

6 6

PRESS

G IH

30o

CutSteady U.S.A.

™

ANGLE GRINDER

CPT30004

NOTE: BEFORE THE POWER TOOL IS USED FOR THE FIRST TIME,

READ THIS INSTRUCTION MANUAL AND KEEP IT FOR FUTURE

REFERENCE.

DETAILED SAFETY REGULATIONS

Safety Warnings Common for Grinding, Sanding, Wire

Brushing, Polishing or Abrasive Cutting-O Operations:

a) This power tool is intended to function as a grinder, sander,

this power tool. Failure to follow all instructions listed below may

b) Operations such as polishing are not recommended to be

performed with this power tool. Operations for which the

power tool was not designed may create a hazard and cause

personal injury.

and recommended by the tool manufacturer. Just because the

accessory can be attached to your power too, it does not assure

safe operation.

d) The rated speed of the accessory must be at least equal to

the maximum speed marked on the power tool. Accessories

e) The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately guarded or

controlled.

f) Threaded mounting of accessories must match the grinder

Accessories that do not match the mounting hardware

of the power tool will run out of balance, vibrate excessively and

may cause loss of control.

g) Do not use a damage accessory. Before each use inspect

the accessory such as abrasive wheels for chips and cracks,

backing pad for cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or accessory is dropped,

inspect for damage or install an undamaged accessory. After

inspecting and installing an accessory, position yourself and

bystanders away from the plane of the rotating accessory

and run the power tool at maximum no-load speed for one

minute. Damaged accessories will normally break apart during

this test time.

h) Wear personal protective equipment. Depending on

application, use face shield, safety googles or safety glasses.

As appropriate, wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping small abrasive

or workpiece fragments. The eye protection must be capable

generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loos.

i) Keep bystanders a safe distance away from work area. Anyone

entering the work area must wear personal protective

equipment. Fragments of workpiece or of a broken accessory may

j) Hold the power tool by insulated gripping surfaces only,

when performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed metal parts of the

power tool“live”and could give the operator an electric shock.

k) Position the cord clear of the spinning accessory. If you lose

control, the cord may be cut or snagged and your hand or arm

may be pulled into the spinning accessory.

l) Never lay the power tool down until the accessory has come

to a complete stop. The spinning accessory may grab the surface

and pull the power tool out of your control.

m) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag your

clothing, pulling the accessory into your body.

n) Regularly clean the power tool’s air vents. The motor’s fan will

draw the dust inside the housing and excessive accumulation of

powdered metal may cause electrical hazards.

Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which in

turn causes the uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump toward or away

from operator, depending on direction of the wheel’s movement at

the point of pinching. Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by taking

proper precautions as given below.

body and arm to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up. The operator can

control torque reaction or kickback forces, if proper precautions

are taken.

b) Never place your hand near the rotating accessory. Accessory

may kickback over your hand.

c) Do not position your body in the area where power tool will

move if kickback occurs. Kickback will propel the tool in direction

opposite to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges etc. Avoid

bouncing and snagging the accessory. Corners, sharp edges or

bouncing have a tendency to snag the rotating accessory and

cause loss of control of kickback.

e) Do not attach a saw chain woodcarving blade or toothed saw

blade. Such blades create frequent kickback and loss of control.

Safety Warnings Speciﬁc for Grinding and Abrasive Cutting-

Oﬀ Operations:

a) Use only wheel types that are recommended for your power

Wheels for which the power tool was not designed cannot be

adequately guarded and are unsafe.

b) The grinding surface of centre depressed wheels must be

mounted below the plane of the guard lip. An improperly

mounted wheel that projects through the plane of the guard lip

cannot be adequately protected.

c) The guard must be securely attached to the power tool and

positioned for maximum safety, so the least amount of wheel

is exposed towards the operator. The guard helps to protect the

operator from broken wheel fragments, accidental contact with

wheel, and sparks that could ignite clothing.

d) Wheels must be used only for recommended applications. For

Abrasive

applied to these wheels may cause them to shatter.

size and shape for your selected wheel.

CutSteady U.S.A.

™

support the wheel thus reducing the possibility of wheel

f) Do not use worn down wheels from larger power tools. Wheel

intended for larger power tool is not suitable for the higher speed

of a smaller tool and may burst.

Additional Safety Warnings Speciﬁc for Abrasive Cutting-Oﬀ

Operations:

not attempt to make an excessive depth of cut. Overstressing

the wheel increases the loading and susceptibility to twisting or

binding of the wheel in the cut and the possibility of kickback or

wheel breakage.

b) Do not position your body in line with and behind the rotating

wheel. When the wheel, at the point of operation, is moving away

from your body, the possible kickback may propel the spinning

wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any

motionless until the wheel comes to a complete stop. Never

wheel is in motion otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of wheel binding.

d) Do not restart the cutting operation in the workpiece. Let

the wheel reach full speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the power tool is restarted

in the workpiece.

e) Support panels or any oversized workpiece to minimize the

risk of wheel pinching and kickback. Large workpieces tend to

sag under their own weight. Support must be placed under the

workpiece near the line of cut and near the edge of the workpiece

on both sides of the wheel.

f) Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding wheel may cut gas or

water pipes, electrical wiring or objects that can cause kickback.

Safety Warnings Speciﬁc for Sanding Operations:

a) Do not use excessively oversized sanding disc paper. Follow

manufacturers recommendations, when selecting sanding

paper. Larger sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snagging, tearing of

the disk or kickback.

Safety Warnings Speciﬁc for Polishing Operations:

a) Do not allow any loose portion of the polishing bonnet or its

attachment strings to spin freely. Tuck away or trim any loose

attachment strings. Loose and spinning attachment strings can

Safety Warnings Speciﬁc for Wire Brushing Operations:

a) Be aware that wire bristles are thrown by the brush even

during ordinary operation. Do not overstress the wires by

applying excessive load to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire brushing, do

not allow any interference of the wire wheel or brush with the

guard. Wire wheel or brush may expand in diameter due to work

load and centrifugal forces.

Additional safety Warnings:

a) In tools adapted to attach grinding wheels with a threaded hole,

check whether the thread length of the grinding wheel is suitable

for the length of the spindle thread.

b) Secure the workpiece. Attaching the workpiece to the clamping

device or vise is safer than holding it in your hand.

c) Do not touch the cutting and grinding discs until they have

cooled down.

rubber O-ring and that the ring is undamaged. It should also

discs.

f) In the event of a temporary power outage in the network or after

removing the plug from the power socket with the switch in the

"on" position, before re-starting, unlock the switch and set it in the

CAUTION! This device is designed to operate indoors. The

design is assumed to be safe, protection measures and

additional safety systems are used, nevertheless there is

always a small risk of injuries at work.

Descriptions of used pictograms.

1 2 3 4

5 6 7 8

1. Warning, take special precautions.

2. Read the instruction manual, observe warnings and safety

conditions included in it!

3. Use personal protection equipment (safety goggles, ear

protectors).

4. Use safety gloves.

5. Disconnect the power cord, before maintenance or repair works

are begun.

6. Keep out of reach of children.

7. Protect against rain

8. Protection class II

DESIGN AND APPLICATION

The angle grinder is a hand-held power tool with the II class isolation.

The power tool is driven with a single-phase, commutator motor,

whose rotational speed is reduced by means of an intersecting

axis gear. The power tool can used both for grinding and cutting.

This type of power tools is widely used for removal of burrs from

metal surfaces, weld surface processing, cutting light-wall tubes and

other small metal objects etc. They are used in engineering industry,

automotive and chemical industry. With the use of proper tools, the

angle grinder can be used not only for cutting or grinding, but also

for rust and paint coats removal.

The areas of its application include repair and construction works,

not only related to metals. The angle grinder can also be used for

cutting and grinding of construction materials, such as brick, paving

stones, ceramic tiles, etc.

The power tool is designed for dry operation only and it must not

be used for polishing. The power tool should be used according

to its purpose.

Use inconsistent with its purpose

•Do not work materials that contain asbestos. Asbestos is

carcinogenic.

•

During operation, the power tool produces sparks, which may ignite

emitted vapours.

•

used to cut with its face, while grinding with lateral surface of such

danger of injuries.

DESCRIPTION OF GRAPHIC PAGES

The below list refers to device components shown in the graphic

pages of this instruction manual.

1. Spindle lock button

2. Switch

3. Additional handle

CutSteady U.S.A.

™

4. Grinding wheel cover

10. Lever (grinding disc guard)

DESCRIPTION OF USED GRAPHIC SIGNS

NOTE

WARNING

FITTING/SETTING

INFORMATION

EQUIPMENT AND ACCESSORIES

1. Grinding wheel guard - 1 pce

2. Socket spanner - 1 pce

3. Additional handle - 1 pce

PREPARATION FOR WORK

ATTACHING THE ADDITIONAL HANDLE

The additional handle (3) is installed in one of the holes in the

grinder head. It is recommended to use the grinder with the

additional handle. When holding the grinder with both hands (also

using the additional handle), there is less risk of touching the grinder

wheel or brush with your hand, as well as of injuries during recoil.

INSTALLING AND ADJUSTING THE GRINDING WHEEL GUARD

pieces and accidental contact with a working tool or sparks. The

that its covering part faces the operator.

•The design of the wheel guard mounting allows for toolless

setting of the guard in an optimum position.

•Loosen and pull back the lever (10) on the wheel guard (4).

•Rotate the wheel guard (4) in a selected position.

•Lock by lowering the lever (10).

The removal and adjustment of the wheel guard are performed in a

reverse order to its installation.

REPLACEMENT OF WORKING TOOLS

When working tools are replaced, wear working gloves at all

times.

The spindle lock button (1) is only designed to lock the grinder

spindle, when a working tool is installed or removed. Do not use

it as a braking button, when the wheel rotates. Otherwise, the

grinder may become damaged or the user may be injured.

INSTALLING THE WHEELS

•Press the spindle lock button (1).

•

(5) ( ).

•5).

•Place the wheel so it is pressed against the surface of the inner

6).

•5) and slightly tighten it with the special

key.

The wheel is removed in the reverse order. During installation, the

and seated centrally in the neck.

INSTALLING THE WORKING TOOLS WITH THREADED HOLES

•Press the spindle lock button (1).

•Remove a previously installed working tool, if it is installed.

•

6 5).

•Put the threaded part of a working tool onto the spindle and

slightly tighten.

Working tools with threaded holes are removed in the reverse order.

INSTALLING THE ANGLE GRINDER ON A TRIPOD FOR ANGLE

GRINDERS

The angle grinder can be used on a dedicated tripod for angle

grinders, provided that it is correctly installed according to

instructions of the manufacturer of a tripod.

OPERATION / ADJUSTMENTS

Before the grinder is used, check condition of the grinding wheel.

Do not use chipped, broken or otherwise damaged grinding

wheels. Worn grinding wheel or brush should be immediately

replaced with new one before use. Once your work is completed,

complete stop. Only then the grinder can be put aside. Do not

.eceipkrowatsniagatignisserpybleehwgnidnirggnitatoraekarb

•Do not overload the grinder. The weight of the power tool exerts

and excessive pressure may lead to dangerous cracking of the

working tool.

•If the grinder is dropped during operation, it should be checked

and a working tool might need to be replaced, when it is

damaged or deformed.

•Never strike the workpiece with a working tool.

•Do not use the grinding wheel for hammering or stripping

of the workpiece, especially when corners, sharp edges are

worked, etc. (this may cause loss of control of the power tool

and recoil).

•Do not use discs from circular saws intended for wood cutting.

Failure to observe this recommendation may result in recoil of

the power tool, loss of control and may lead to injuries of the

operator.

SWITCHING ON /SWITCHING OFF

When the grinder is switched on and operated, it should be held

with both hands.

•Press the rear part of the switch (2).

•Move the switch (2) forwards - (towards the head) ( ).

•Press the front part of the switch for continuous operation.

•The switch will be automatically locked in the position for

continuous operation.

•Press the rear part of the switch (2

Once the grinder is switched on, wait until the grinding wheel

reaches maximum speed and only then you can begin to work.

During operation do not use the switch to switch the grinder on

is moved away from the workpiece.

The tool is equipped with a switch with undervoltage release

feature. In case of temporary mains power failure or connecting to

mains socket with switch in ON position, the tool will not start. In

such case move the switch to OFF position and switch it on again.

CUTTING

•The angle grinder can be used for cutting in a straight line only.

•Do not cut a workpiece holding it in your hands.

•Large workpiece should be supported. Make sure the support

points are located near the cutting line and at the ends of the

workpiece. A stably located workpiece will not tend to move,

when it is cut.

•Small workpieces should be fastened in a vice or using clamps,

for example. The workpiece should be fastened so that it is cut

CutSteady U.S.A.

™

near the fastening element. This will ensure higher cutting

precision.

•

break.

•

cutting.

•

workpiece type.

•When a workpiece is cut, it is recommended that a cutting

The cutting depth depends on a wheel diameter ( ).

•Only wheels with nominal diameters not larger than

recommended for a given grinder model should be used.

•

of deep cuts (e.g. sections, building blocks, bricks, etc.).

cannot be touched with uncovered body parts, before they cool

down.

GRINDING

grinding. Each type of discs and workpiece requires proper working

method and personal protective equipment.

Grinding discs are intended for removal of material with an edge

of the disc.

•Do not use the lateral surface for grinding. The optimum

•Works related to grinding can be performed only, when proper

grinding discs are used for a given workpiece.

sandpaper are used, attention should be paid to the proper tool

•Do not grind with the entire surface of a wheel.

•

Wire brushes are mainly used for cleaning sections and hard-to-

reach spaces. They can be used to remove rust, painting coats, etc.

Only such working tools can be used, whose permissible

rotational speed is higher or equal to the maximum no load speed

of the grinder.

OPERATION AND MAINTENANCE

Before any operations related to installation, adjustment, repairs

or maintenance are commenced, the plug of the power cord

should be disconnected from the socket.

MAINTENANCE AND STORAGE

•It is recommended to clean the tool after each use.

•

•The tool should be cleaned with a dry piece of cloth or blown with

compressed air of low pressure.

•Do not use any cleaning agents or solvents, since they may

damage plastic parts.

•Venting slots in the motor housing should be cleaned on a regular

basis not to overload the tool.

•When the power cord is damaged, it should be replaced with

the power cord of the same parameters. It should be performed

authorised service shop.

•When the commutator sparks excessively, have the condition of

•The tool should be always stored in a dry place and out of reach

of children.

REPLACING THE CARBON BRUSHES

Worn (shorter than 5 mm), burnt or cracked motor carbon brushes

should be immediately replaced. Both carbon brushes should be

always replaced at the same time.

original spare parts only.

All types of faults and defects should be eliminated by an authorised

service of the manufacturer.

SPECIFICATIONS

RATED DATA

Angle Grinder

Parameter Value

Power supply voltage 230 V AC

Power supply frequency 50 Hz

Rated power 1100W

Rated rotational speed 11000 RPM

Max. grinding wheel diameter 125 mm

Inner disc diameter 22.2 mm

Spindle thread M14

Protection class II

Weight 2.05 kgs

Year of manufacture 2019

NOISE AND VIBRATION DATA

Information regarding noise and vibration

The following levels of emitted noise, such as emitted acoustic pressure

LpAand acoustic power level LwAand measurement uncertainty K

standard.

The following vibration value (acceleration value) ahand

EN 60745 standard.

The vibration level provided in this instruction manual have been

the EN 60745 standard and can be used for comparison of power

tools. This can be used for preliminary assessment of exposure to

vibrations.

The provided vibration level is representative for main applications

of the power tool. If the power tool is used for other applications or

vibration level may vary. The aforementioned reasons may increase

the exposure to vibrations during the entire operating period.

In order to precisely estimate the exposure to vibrations, periods

when it is switched on, but not operated. Thus, the total exposure to

vibration may prove considerably lower.

Additional safety measures should be taken to protect the user

and its working tools, ensuring proper temperature of the hands and

proper organisation of work.

Acoustic pressure level: LpA = 86 dB(A) K= 3 dB(A)

Acoustic power level: LwA= 97 dB(A) K= 3 dB(A)

Vibration acceleration value: ah= 5,50 m/s2K= 1,5 m/s2

CutSteady U.S.A.

™

ENVIRONMENTAL PROTECTION

waste and, instead, should be utilized at appropriate facilities.

Information on utilization can be provided by the product

vendor or the local authorities. Waste electrical and electronic

equipment contains substances that are not neutral to

the natural environment. Equipment that is not recycled

constitutes a potential hazard to the environment and to

human health.

* Right to introduce changes is reserved.

CutSteady U.S.A.

™

PRODUCT USE

All statements, technical information and recommendations

contained in this document are based up on tests or experience that

CutSteady believes are reliable. However, many factors beyond

CutSteady’s control can aect the use and performance of a

CutSteady product in a particular application, including the

conditions under which the CutSteady product is used and the time

and environmental conditions in which the product is expected to

perform. Since these factors are uniquely within the user’s

knowledge and control, it is essential that the user evaluate the

CutSteady product to determine whether it is t for a particular

purpose and suitable for the user’s method of application.

LIMITATION OF LIABILITY

CutSteady and seller will not be liable for any loss or damage arising

from the CutSteady product, whether direct, indirect, special,

incidental or consequential, regardless of the legal theory asserted,

including warranty, contract, negligence or strict liability except

where prohibited by law.

ПЕРЕВОД ОРИГИНАЛЬНОЙ

ИНСТРУКЦИИ

МАШИНА ШЛИФОВАЛЬНАЯ

УГЛОВАЯ

CPT30004

ВНИМАНИЕ: ПЕРЕД НАЧАЛОМ ЭКСПЛУАТАЦИИ РУЧНОЙ

ЭЛЕКТРИЧЕСКОЙ МАШИНЫ СЛЕДУЕТ ВНИМАТЕЛЬНО

ПРОЧИТАТЬ ДАННУЮ ИНСТРУКЦИЮ И СОХРАНИТЬ В

КАЧЕСТВЕ СПРАВОЧНОГО МАТЕРИАЛА.

ЧАСТНЫЕ ТРЕБОВАНИЯ ПО БЕЗОПАСНОСТИ

Указания мер безопасности, касающиеся шлифования,

шлифования шкуркой, зачистки с помощью проволочных

щеток и абразивной резки.

a) Данная ручная электрическая машина предназначена

для применения в качестве стандартной шлифовальной

машины, шлифмашины для шлифования шкуркой,

для зачистки проволочными щетками, а также для

применения в качестве отрезной машины. Ознакомьтесь

со всеми предупреждениями по безопасности, инструкциями,

иллюстрациями и техническими характеристиками,

предоставленными с данной ручной электрической машиной.

Невыполнение всех приведенных ниже указаний может

привести к поражению электрическим током, пожару и (или)

к тяжелому телесному повреждению.

b) Не производите данной ручной машиной такие работы,

как полирование. Производство работ, для которых ручная

машина не предназначена, может создавать опасность и

вызывать телесные повреждения.

c) Не пользуйтесь рабочим инструментом и другими

вспомогательными устройствами, которые не

предназначены специально для этой машины и не

рекомендованы изготовителем машины. Одна только

возможность их крепления к данной ручной машине не

обеспечивает ее безопасную работу.

d) Номинальная частота вращения для рабочего

инструмента должна быть не менее максимальной

частоты вращения, указанной на маркировке

электрической ручной машины. При работе рабочим

инструментом, вращающимся быстрее номинальной частоты

вращения, может произойти его разрыв и разлет фрагментов.

e) Наружный диаметр и толщина рабочего инструмента

должны быть в пределах номинальных размеров данной

электрической ручной машины. Несоразмерные рабочие

инструменты не могут быть в достаточной мере ограждены

и при работе могут приводить к потере управления машиной

f) Рабочий инструмент с резьбовым вкладышем должен

подходить к резьбе шпинделя. Рабочий инструмент,

закрепляемый с помощью фланцев, должен

соответствовать диаметру фланца. Рабочий инструмент

с посадочными отверстиями, не соответствующими

средствам крепления электрической ручной машины, будет

несбалансированным, он будет вызывать повышенную

вибрацию и может привести к потере управления.

g) Не применяйте поврежденный рабочий инструмент.

Перед каждым использованием осматривайте

рабочий инструмент, например шлифовальные круги

– на предмет наличия сколов и трещин; тарельчатые

шлифовальные диски – на наличие трещин, разрывов или

чрезмерного износа; проволочную щетку – на предмет

незакрепленных или надломанных проволок. После

падения электрической ручной машины или рабочего

инструмента нужно производить осмотр на наличие

повреждений или заменить его на неповрежденный

рабочий инструмент. После осмотра и монтажа рабочего

инструмента оператор и все находящиеся вблизи лица

должны занять положение за пределами плоскости

вращения рабочего инструмента, после чего включите

ручную машину для работы на максимальной частоте

вращения на холостом ходу в течение одной минуты. В

большинстве случаев за время контроля происходит разрыв

поврежденного рабочего инструмента.

h) Пользуйтесь средствами индивидуальной защиты.

В зависимости от выполняемой работы пользуйтесь

защитным лицевым щитком, закрытыми или открытыми

защитными очками. По мере необходимости пользуйтесь

пылезащитной маской, средствами защиты органов

слуха, перчатками и защитным фартуком, способным

задерживать мелкие абразивные частицы и частицы

обрабатываемого материала. Средства защиты органов

зрения должны быть способны задерживать разлетающиеся

частицы, образующиеся при производстве различных

работ. Пылезащитная маска или респиратор должны

отфильтровывать частицы, образующиеся при производстве

работ. Длительное воздействие шума высокого уровня может

вызвать потерю слуха.

i) Не допускайте посторонних непосредственно близко к

рабочей зоне. Любые лица, входящие в рабочую зону,

должны носить средства индивидуальной защиты.

Фрагменты объекта обработки или поломанного рабочего

инструмента могут разлетаться и вызывать телесные

повреждения в непосредственной близости от места

производства работы.

j) При производстве работы, при которой абразивный

инструмент может прикоснуться к скрытой проводке,

удерживайте ручную машину только за изолированную

поверхность захвата. При прикосновении к находящемуся

под напряжением проводу открытые металлические части

ручной машины могут попасть под напряжение и вызывать

поражение оператора электрическим током.

k) Необходимо отводить кабель от вращающегося рабочего

инструмента. При потере управления кабель может быть

поврежден или зажат, что повлечет за собой затягивание

кисти или руки в зону вращающегося рабочего инструмента.

l) Никогда не кладите ручную машину до полной остановки

рабочего инструмента. Вращающийся рабочий инструмент

может зацепиться за поверхность и вырвать электрическую

ручную машину из рук.

m) Запрещается включать электрическую ручную машину

во время ее переноски. Случайное прикосновение к

вращающемуся рабочему инструменту может захватить

одежду и нанести травму.

n) Нужно регулярно производить очистку вентиляционных

отверстий ручной машины. Вентилятор электродвигателя

затягивает пыль внутрь корпуса, чрезмерное скопление

металлизированной пыли может привести к опасности

поражения электрическим током.

o) Строго запрещена работа электрической ручной

машиной вблизи легковоспламеняющихся материалов.

Эти материалы могут воспламениться от искр.

p) Нельзя пользоваться рабочими инструментами,

требующими применения жидких охлаждающих средств.

Применение воды или иных охлаждающих средств может

привести к поражению электрическим током.

Отскок и соответствующие предупреждения

Отскок – это реакция машины на внезапное заедание

или заклинивание вращающегося шлифовального круга,

шлифовального тарельчатого диска, щетки или иного рабочего

инструмента. Заклинивание вызывает резкое торможение

вращающегося рабочего инструмента, что приводит к

возникновению силы отдачи, воздействующей на ручную

машину, направленной противоположно направлению

вращения рабочего инструмента и приложенной в точке

заклинивания.

CutSteady U.S.A.

™

Indice

Lingue:

Altri manuali CutSteady Macinacaffè

CutSteady

CutSteady CPT30001 Manuale utente

Manuali Macinacaffè popolari di altre marche

Parkside

Parkside PWS 230 C3 Manuale utente

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Manuale tecnico

PTA

PTA P1322 Manuale utente

Crown

Crown CT13313 Manuale utente

Parkside

Parkside 280250 Manuale utente

Climax

Climax VM2150 Series Manuale utente

Jet

Jet JPSG-618M1 Manuale di servizio

Makita

Makita GA4030 Manuale utente

DeWalt

DeWalt DWEN202 Manuale utente

Grizzly

Grizzly G2790 Manuale utente

Fein

Fein MSf843-1a Manuale utente

Bosch

Bosch GWS 14,4 V PROFESSIONAL Manuale utente

RAMSET

RAMSET CBAGR18 Manuale utente

Bosch

Bosch 8-115 Z Manuale utente

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Manuale utente

MW TOOLS

MW TOOLS ME15W Manuale utente

Caravaggi

Caravaggi SP 20 Istruzioni operative

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Manuale tecnico