CyberPower RMCARD301 Manuale utente
QUICK INSTALLATION GUIDE
Network Management Card
RMCARD301
The RMCARD301 Network Management Card provides for advanced ups management and configuration.
INSTALLATION GUIDE
Description:
LED Status indicator TABLE
Yellow Red Green Status
Off Off ON Power ON
Flashing ON ON System initial
ON Off ON Normal operation
ON Flashing ON No connection to
UPS
Flashing Flashing ON Writing data to flash
memory
Green light : Power state
Red light : Connection state with UPS
Step 1. Hardware Installation
(1) Insert the RMCARD301 into the UPS management card slot
(2) Connect the network cable
Step 2. Configure the IP address and update the firmware.
Section 1. Install Netility
(1) Insert the NetAgent Utility CD to the CD-ROM driver and execute Netility.exe.
(2) After the installation completes, there will be a ‘Netility’ group in Windows ’Start’ -> ‘Program Group’.
(3) Click "Netility" to launch Netility and enter the main configuration screen.
Section 2. Using Netility
The main Netility screen shows a list of all the RMCARD301s found on the network and shortcuts to configure, update, or launch the device.
(1) Launch Device
Click Launch Device or double click the RMCARD301 listed in the table to launch it.
Enter the Account (Login Name) and Password (Login Password) to login. If an Account and Password have not been configured click "Apply"
to login.
(2) Configure
Choose the RMCARD301 from the table, then click “Configure”.
IP Address: Set the IP address for the RMCARD301
Select DHCP, BOOTP, or Static IP. For a static IP configure the IP address, subnet mask and gateway. After configuring the settings the
RMCARD301 interface is accessible using a browser or telnet.
Advanced: RMCARD301 Settings
In order to ensure the secure management the RMCARD301 provides two security options to control access to the management interface.
RMCARD301 Password
After setting the password all commands given to the RMCARD 301 by the Netility software will require the password. (Make sure to remember
the password. )
Management Protocol
The RMCARD301 provides HTTP (web) and Telnet access for management. For security purposes the port for each protocol can be configured.
1. On the advanced tab select HTTP and Telnet management and the port to use for each. The default ports for each protocol can be used.
2. If using a port other than the default for HTTP (80) or Telnet (23) the full IP address and port must be used to access the RMCARD301.
For example,
(a) Set 81 as HTTP port number, then http://192.168.0.177:81 must be typed at the web address to proceed to RMCARD301 web interface.
(b) Set 24 as Telnet port number, then "192.168.0.177:24" must be typed at Telnet to proceed to the RMCARD301 Telnet interface.
(3) Download Firmware
The RMCARD301 offers a simply method to upgrade the firmware. To upgrade firmware, click Download Firmware from RMCARD301 Setup
menu, click “Browser” select new firmware file (*.bin) and press “Start”. The RMCARD301's Red LED and Yellow LED will flash to indicate the
firmware is upgrading. After the upgrade is complete the RMCARD301 will reboot. To upgrade multiple RMCARD301s with the same firmware,
press and hold the Ctrl key and select the RMCARD301s to upgrade.
(To obtain the latest firmware please visit http://www.megatec.com.tw ) If upgrading multiple units, select the option for multiple NetAgent
upgrades.
Note: The RMCARD301 provides a fail safe method to upgrade the firmware. If the upgrade is interrupted the RMCARD301 will revert to the
previous firmware. If the upgrade fails simply repeat the upgrade process.
(4) About - Displays details about the current version of Netility.
(5) Refresh - Forces netility to scan the network for RMCARD301s.
Netility will automatically scan the network or the refresh button can be used to force another scan..
RMCARD301 Web Management
Section 1. Introduction
After completing the RMCARD301 installation, you will now be able to go to RMCARD301 web interface to monitor and control UPS by inputting
RMCARD301 IP address in a web browser.
(1) Launch a web browser (Firefox or Internet Explorer)
(2) Enter the RMCARD301 IP Address previously configured e.g. 192.168.0.177.
Enter the RMCARD301 IP address
(3) On the first screen, enter the previously configured password. If no password has been configured press [ENTER].
RMCARD301 Login dialog
Section 2. RMCARD301 NetAgent Web Interface
There are 4 main function categories on the initial screen.
2.1 Information
2.2 Configuration
2.3 Log Information
2.4 Help
Select the main category on the left and the subcategory. When using NetAgent for the first time, please enter the [Configuration] category
to set the necessary configurations.
2.1 Information
Sub-Menu :
2.1.1 System Status
2.1.2 Basic Information
2.1.3 Current Status
2.1.4 Remote Control
2.1.5 Meter/Chart
2.1.1 System Status
This screen displays the NetAgent system information and Network settings. Values shown here are either provided by NetAgent itself or they are
user settings from the Configuration pages.
System Information
This section displays the NetAgent system information. Values in Hardware Version/Firmware Version/Serial Number/System Time are provided
by NetAgent itself. Other values are user settings from the Configuration pages.
Network Status
This section displays NetAgent Network settings. The MAC address is provided by NetAgent. All other values in this section are user settings from
the Configuration pages.
Indice
Altri manuali CyberPower Hardware per computer
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
