CyData Daisy Manuale utente

Thermostat

Wi-Fi Enabled

INSTALL GUIDE

3:37 PM 30%

Set

Auto

Fan

Heat

Mode

INSTALLING THERMOSTAT

1 Switch power OFF to your HVAC system.

Important! Switch the power OFF to your HVAC

systems at the breaker box or the system switch to

protect your system.

2Leave wires connected and remove old

thermostat from wall.

Take photos of wire connections

to reference later on.

3 Label the wires.

Do not label wires by color. Use the tags included

to label as you disconnect each wire. Wires should

be labeled according to your existing thermostat

terminal assignments, not by color.

Note: Blank tags are provided to write the terminal

label if you ﬁnd no matching tags exist.

RC W

R Y C

Inside your Daisy thermostat box.

1. Daisy Wi-Fi Thermostat

2. Thermostat Base

3. Mounting Hardware

4. Quick Guide

5. Wiring Labels

Circuit breaker box

HVAC system

power switch

DAISY Wi-Fi Programmable Thermostat / INSTALL GUIDE 2

INSTALLING THERMOSTAT

Important! Check wire terminal compatibility with User Guide before starting installation.

3:37 PM 30%

Set

Auto

Fan

Heat

Mode

WARNING: This thermostat works with common 24 volt

system. It will not work with millivolt systems or with 120/240

volt systems such as baseboard electric heat.

NOTICE: To avoid possible compressor damage, do not run air

conditioner if the outside temperature drops below 50˚F (10˚C)

MERCURY NOTICE: Do not place your old thermostat in the

trash if it contains mercury. Contact the Thermostat Recycling

Corporation at www.thermostat-recycle.org or

1-800-238-8192 for information on how and where to

properly and safely dispose of your old thermostat.

4 Remove the wallplate.

After all wires have been labeled and disconnected,

remove the existing wallplate from the wall.

5 Separate the new Wi-Fi thermostat from its wall plate

Grab hold of the back corners while holding the front of

the new thermostat. Hold the wallplate tightly to pull the

thermostat apart.

6Mount new Wi-Fi thermostat wallplate

Screws and anchors are provided to mount

the new wallplate. Existing wall anchors may

be usable and can be checked by holding

the new wallplate up to the anchors

to check that they are in alignment.

7Wiring for conventional system.

Note: You must have a C Wire or equivalent.

a Start with the C wire to match the tag on the wire

to the terminal label.

bLoosen the screw. Insert wire on inside edge

of terminal, then tighten screw.

c Give wire a gentle tug to conﬁrm wire is secure.

d Repeat steps a-c for remaining wires.

e Excess wire should be pushed back into

opening of wall.

f Continue to step 8 on page 5.

INSTALLING THERMOSTAT

Note: Remove metal jumper only if you

have both R and RC wires.

Note: Wiring will be speciﬁc to each application

and may be different than wiring shown above.

DAISY Wi-Fi Programmable Thermostat / INSTALL GUIDE 3

Wiring

cross reference

Conventional

Heat pump

RC R Y C O/B G AUX/E L

INSTALLING THERMOSTAT

Note: Wiring will be speciﬁc to each

application and may be different than

wiring shown below.

Note: If the old thermostat has separate

wires on AUX and E, place both wires into the

AUX/E terminal. No jumper is required.

Wiring for heat pump system only.

Note: You must have a C Wire or equivalent.

a Start with the C wire and continue to match the rest of

the tags on the wires to the terminal labels.

bLoosen the screw. Insert wire on inside edge of terminal,

then tighten screw.

c Give wire a gentle tug to conﬁrm wire is secured.

d Repeat steps a-c for remaining wires.

e Excess wire should be pushed back into opening of wall.

f Continue to step 8 on page 5.

W2 Y2

DAISY Wi-Fi Programmable Thermostat / INSTALL GUIDE 4

7.1

7.2

Alternate Wiring for conventional system.

Note: You must have a C Wire or equivalent.

1 Remove metal jumper if the old thermostat had

both Rand RH wires.

2 Only remove metal jumper connecting R

and RC if you must connect both Rand RC.

INSTALLING THERMOSTAT

8 Attach the new Wi-Fi thermostat to wallplate.

Important!

Verify the C Wire is connected at the thermostat

and at the HVAC system.

Check that thermostat and the wallplate are aligned,

then snap securely into place.

DAISY Wi-Fi Programmable Thermostat / INSTALL GUIDE 5

AUX

Alternate Wiring for heat pump system only.

Note: You must have a C Wire or equivalent to install.

1 If the old thermostat had separate wires on AUX

and E, insert both wires into the AUX/E terminal.

No jumper is required.

2 If the old thermostat had an Owire and not a B

wire, insert the Owire to the O/B terminal.

7.3

RC R Y C O/B G AUX/E L

9 Switch HVAC system ON.

Important!

Secure the HVAC system door ﬁrmly.

Switch ON power for the HVAC system

at the breaker box or power switch.

10 Set-up thermostat (see User Guide).

Circuit breaker box

HVAC system

power switch

Altri manuali per Daisy

Indice

Altri manuali CyData Termostato

CyData

CyData Daisy Manuale utente

Manuali Termostato popolari di altre marche

EWELLY

EWELLY EW-181 Manuale utente

Prolon

Prolon T1100 Istruzioni per l'installazione

Computherm

Computherm Q20 Manuale utente

Heatmiser

Heatmiser neoStat Manuale utente

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuale utente

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuale utente

Saswell

Saswell SAS920XWHB-7-S-RF Guida

Aircalo

Aircalo TFP1-ET85P2 Manuale utente

Honeywell

Honeywell CM721 Manuale utente

Carrier

Carrier DEBONAIR 33CS Manuale utente

Lennox

Lennox iHarmony Zone Thermostat Istruzioni per il montaggio

Gemtech

Gemtech GT7000 Manuale di istruzioni

Rollei

Rollei Smartes 45000 Manuale utente

Sinope

Sinope TH1300RF Manuale utente

Honeywell

Honeywell RLV4305 Manuale utente

Honeywell

Honeywell Prestige 2.0 THX9421 Manuale utente

NuTone

NuTone NTBZ48 Istruzioni operative originali

Stelpro

Stelpro MAESTRO ASMT402AD Manuale utente