Cypress Suprex SPX-1300 Manuale utente

Operations Manual

Suprex® Reader Extender

SPX-1300

*/5&(3"5*0/40-65*0/4

CYPRESS

q!`123458r!

Electrical and Mechanical Speciﬁcations

Physical

SPX-1300 Aluminum Enclosure 3.5" x 2.75" x .75"

Temp

Storage(-55˚C to + 150˚C)"

Operating(-40˚C to +80˚C)

Humidity

95% (non-condensing)

Power

Input

Unreg Input 8 to 16 VDC* @ 200mA Max

Output

+5VDC @100mA

Data I/O"

Voltage Ratings

Interface

Reader 0- 30VDC"

LED - 0 - 30VDC"

Analog 0 - 5 VDC"

*See Notes on following page for temperature and power ratings

3.3”

DataBender CVX-1300

2.8”

1.4”

3.65”

ø 0.15”

External Dimensions and Mounting Holes

Unit Height = 0.75”

This complies with part 15 of the FCC rules !

Operation is subject to the following two conditions: !

(1) This device may not cause harmful interference, and !

(2) this device must accept any interference received, including

interference that may cause undesired operation.

Cypress Computer Systems, Inc. ⌖Lapeer, MI 48446 ⌖www.cypresscomputer.com

External connections and DIP Switch Settings

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-Prog Res 2"

4-Prog Res 1"

3-LED Input"

2-D1/Data/F2F Out-"

1-D0/CLK Out

2-8 to 16 VDC In"

1-Ground

Diagnostic LED

12-RLY4 N.O."

11-RLY4 Com"

10-RLY4 N.C."

9-RLY3 N.O."

8-RLY3 Com"

7-RLY3 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux Out"

2-Relay2 Input"

1-Relay1 Input"

Central Unit

2-8 to 16 VDC In"

1-Ground

12-RLY2 N.O."

11-RLY2 Com"

10-RLY2 N.C."

9-RLY1 N.O."

8-RLY1 Com"

7-RLY1 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux In"

2-N/C"

1-N/C"

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-RLY4 Input (5V)"

4-RLY3 Input (5V)"

3-LED Output"

2-D1/Data/F2F Input"

1-D0/CLK Input

Remote Unit

Note: F/2F connections"

support unsupervised "

mode only.

Switch

6 7 8

1 x

2 x

3 x x

4 x

5 x x

6 x x

7 x x x

Wiegand

Wiegand / No Filter

Strobed Rising Edge (MR-5)

Strobed Rising Edge (Dorad0 644)

Strobed Rising (Mag-Tek)

Strobed Falling Edge

Reserved

F2F

x = ON

Dip switch #4 is ON

-Disable Pullup resistors

Dip switch #4 is OFF

-Enable Pullup resistors

DIP Switch #1 ON "

-Service Mode"

DIP Switch #1 OFF"

-Run Mode

Central Unit !

Settings

Switch

6 7 8

1 x

2 x

3 x x

4 x

5 x x

6 x x

7 x x x

Wiegand

Wiegand / No Filter

Strobed Rising Edge (MR-5)

Strobed Rising Edge (Dorad0 644)

Strobed Rising (Mag-Tek)

Strobed Falling Edge

Reserved

F2F

x = ON

Remote Unit !

Settings

Dip switch #4 is ON

-Enable Pullup resistors

Dip switch #4 is OFF

-Disable Pullup resistors

DIP Switch #1 ON "

-Service Mode"

DIP Switch #1 OFF"

-Run Mode

-40

Ambient Temperature

(Degrees Celsius)

Supply Voltage

Temperature/Voltage de-rating curve

Electrical and Environmental Speciﬁcations

The SPX-1300 units should be operated with a ﬁltered 12 Volt nominal DC supply. "

However, any voltage between 8 and 16 volts can be utilized by following the temperature /voltage derating curve.

Voltage should not exceed 16 VDC."

Digital Data (D0/D1) Inputs and Outputs are OpenCollector with switchable 1k pullup resistors.."

Data I/O Points are rated for the following voltages:"

0 - 5 VDC with pullups on "

0- 24 VDC with pullups off"

All Digital Inputs and Outputs are 0 - 24 VDC tolerant . Pullup resistors should be disabled when using I/O at voltages

greater than 5VDC to prevent excessive current draw and possible component damage. "

Analog Inputs are rated for 5 VDC max."

The Relay 3, Relay 4 inputs and Programming resistor inputs are analog inputs and are limited to 5 volts DC Maximum."

All inputs and outputs are provided with transient and static protection."

The RS-485 communication channel will provide the best performance using shielded twisted pair wiring. Other wire

types can be used, and performance will depend upon actual ﬁeld conditions. The Suprex units will typically function

with: Coax, THHN building wire, Cat5 and Cat 3 cable, etc.

When the Suprex units are operating correctly and have a valid communication channel between"

the Remote and Central units the Diagnostic indicators on each unit will ﬂash green rapidly "

(2-3 ﬂashed per second)."

If the units are not communicating, viewing the diagnostic indicator LED’s may help to determine

the "

nature of the problem."

DIAGNOSTIC LED NOT ILLUMINATED:"

If the LED(s) are not illuminated on the unit(s) then the unit is not getting power. The Diagnostic

LED’s"

will be illuminated when power is applied."

CENTRAL UNIT FLASHING BETWEEN RED/GREEN:"

With power applied and no communication path between the Remote and Central, the Central

unit will ﬂash the diagnostic indicator alternately between Red and Green."

REMOTE UNIT ILLUMINATED RED:"

The Remote unit will diagnostic LED will illuminate solid (not ﬂashing) red if it is not receiving

communication from the Central."

REMOTE AND CENTRAL UNITS FLASHING BETWEEN RED/GREEN:"

The Central is not Receiving communication from the Remote.

Troubleshooting - Diagnostic Indicators

Suprex Operation and Initial Setup

Actual connections will differ based on the type of format, features utilized, and equipment interface."

The following diagrams are an example of a typical installation using the Suprex 1300 and a Wiegand format

Reader and Access Control Panel."

1. First connect units as shown below to verify basic function and communication. This should be done in a

convenient location such as a bench top before installing units in the ﬁeld. Both units can share the same power

supply if the power supply has sufﬁcient capacity. "

When Connected as shown below, both units should have the Diagnostic LED ﬂashing Green about 2-3 ﬂashes

per second (Rapid ﬂashing)

Central Unit

Remote Unit

2-8 to 16 VDC In"

1-Ground

12-RLY2 N.O."

11-RLY2 Com"

10-RLY2 N.C."

9-RLY1 N.O."

8-RLY1 Com"

7-RLY1 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux In"

2-N/C"

1-N/C"

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-RLY4 Input (5V)"

4-RLY3 Input (5V)"

3-LED Output"

2-D1/Data/F2F Input"

1-D0/CLK Input

2-8 to 16 VDC In"

1-Ground

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-Prog Res 2"

4-Prog Res 1"

3-LED Input"

2-D1/Data/F2F Out"

1-D0/Clock Out"

1-D0/CLK Output

12-RLY4 N.O."

11-RLY4 Com"

10-RLY4 N.C."

9-RLY3 N.O."

8-RLY3 Com"

7-RLY3 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux Out"

2-Relay2 Input"

1-Relay1 Input"

8 - 16 VDC "

Power "

Supply

Ground (0V)

+VDC

8 - 16 VDC "

Power "

Supply

Ground (0V)

+VDC

Suprex Operation and Initial Setup

2. Remove power from the units and set DIP switches if necessary. The units are set for Wiegand format data as

the default setting from the factory. If a Wiegand format reader is being used, it should not be necessary to change

the DIP switch setting."

For applications that require a change in the DIP switch setting. Remove the board from the enclosure and set the

DIP switch to the required format on both the Central and Remote units."

Refer to DIP switch diagram for the list of available formats."

3. Connect the Reader to the Remote unit. 2 different standard applications are shown as examples below."

Note: The LED and Door Strike operation of the SPX-1300 differs from previous versions. "

The connection and operation is covered in the next 2 pages.

8 - 16 VDC "

Power "

Supply

DC Power In"

Ground"

LED In"

Data 1"

Data 0

Wiegand Card "

Reader

Remote Unit

2-8 to 16 VDC In"

1-Ground

12-RLY2 N.O."

11-RLY2 Com"

10-RLY2 N.C."

9-RLY1 N.O."

8-RLY1 Com"

7-RLY1 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux In"

2-N/C"

1-N/C"

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-RLY4 Input (5V)"

4-RLY3 Input (5V)"

3-LED Output"

2-D1/Data/F2F Input"

1-D0/CLK Input

485 to "

Central

Wiegand Reader with 8-16 Volt power Connections

485 to "

Central

Wiegand Reader with 5 Volt power supplied by Suprex

8 - 16 VDC "

Power "

Supply

DC Power In"

Ground"

LED In"

Data 1"

Data 0

Wiegand Card "

Reader

Remote Unit

2-8 to 16 VDC In"

1-Ground

12-RLY2 N.O."

11-RLY2 Com"

10-RLY2 N.C."

9-RLY1 N.O."

8-RLY1 Com"

7-RLY1 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux In"

2-N/C"

1-N/C"

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-RLY4 Input (5V)"

4-RLY3 Input (5V)"

3-LED Output"

2-D1/Data/F2F Input"

1-D0/CLK Input

Format setup and Remote Side Basic Reader Connections

Suprex Operation and Initial Setup

Central Side Basic Panel Connections

4. Connect the Central unit to the Access control panel. Power can be supplied by either the Access "

Control Panel or an External Power supply. A ground connection must be provided to the Suprex unit in either case.

485 to "

Central

485 to "

Central

8 - 16 VDC "

Power "

Supply

Ground"

LED In"

Data 1"

Data 0

Wiegand "

Access Control

Wiegand Format Access Control Panel with 8-16 Volt Power From Panel

DC Power"

Ground"

LED In"

Data 1"

Data 0

Wiegand "

Access Control

Central Unit

2-8 to 16 VDC In"

1-Ground

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-Prog Res 2"

4-Prog Res 1"

3-LED Input"

2-D1/Data/F2F Out "

1-D0/Clock Out"

1-D0/CLK Output

12-RLY4 N.O."

11-RLY4 Com"

10-RLY4 N.C."

9-RLY3 N.O."

8-RLY3 Com"

7-RLY3 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux Out"

2-Relay2 Input"

1-Relay1 Input"

Central Unit

2-8 to 16 VDC In"

1-Ground

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-Prog Res 2"

4-Prog Res 1"

3-LED Input"

2-D1/Data/F2F Out "

1-D0/Clock Out"

1-D0/CLK Output

12-RLY4 N.O."

11-RLY4 Com"

10-RLY4 N.C."

9-RLY3 N.O."

8-RLY3 Com"

7-RLY3 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux Out"

2-Relay2 Input"

1-Relay1 Input"

Wiegand Format Access Control Panel with 8-16 Volt Power From External Supply

Suprex Operation and Initial Setup

Central Side Basic Panel Connections

5. To activate the relay on the Remote unit connect as shown below. These connections can be used to allow the

Remote relay to operate a DOOR STRIKE, GATE, or other locking hardware. Refer to following pages in this

document for details of each I/O operation and connection. The Relay inputs are active LOW and will activate the

relay when connected to ground."

There are two relays available for accessory outputs at the Remote end. Either relay can be used to provide the Door

Strike or Gate activation function. This example uses Relay 1.

Central Unit

2-8 to 16 VDC In"

1-Ground

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-Prog Res 2"

4-Prog Res 1"

3-LED Input"

2-D1/Data/F2F Out "

1-D0/Clock Out"

1-D0/CLK Output

12-RLY4 N.O."

11-RLY4 Com"

10-RLY4 N.C."

9-RLY3 N.O."

8-RLY3 Com"

7-RLY3 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux Out"

2-Relay2 Input"

1-Relay1 Input"

Access Control !

Panel

LED OUT

Typical Access Control Panel Connection to activate Door Strike and reader LED.

Strike follows LED

Only Relay and LED Connections are shown for clarity, refer to previous diagrams for

Power,Data and communications connections.

Central Unit

2-8 to 16 VDC In"

1-Ground

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-Prog Res 2"

4-Prog Res 1"

3-LED Input"

2-D1/Data/F2F Out "

1-D0/Clock Out"

1-D0/CLK Output

12-RLY4 N.O."

11-RLY4 Com"

10-RLY4 N.C."

9-RLY3 N.O."

8-RLY3 Com"

7-RLY3 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux Out"

2-Relay2 Input"

1-Relay1 Input"

Access Control !

Panel

LED OUT"

STRIKE

Typical Access Control Panel Connection to activate Door Strike and reader LED. Strike

follows separate panel output.

Remote Unit

Suprex Operation and Initial Setup

I/O Controls

Central Unit

2-8 to 16 VDC In"

1-Ground

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-Prog Res 2"

4-Prog Res 1"

3-LED Input"

2-D1/Data/F2F Out "

1-D0/Clock Out"

1-D0/CLK Output

12-RLY4 N.O."

11-RLY4 Com"

10-RLY4 N.C."

9-RLY3 N.O."

8-RLY3 Com"

7-RLY3 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux Out"

2-Relay2 Input"

1-Relay1 Input"

2-8 to 16 VDC In"

1-Ground

12-RLY2 N.O."

11-RLY2 Com"

10-RLY2 N.C."

9-RLY1 N.O."

8-RLY1 Com"

7-RLY1 N.C."

6-RS232 Out"

5-RS232 In"

4-Ground"

3-Aux In"

2-N/C"

1-N/C"

8-485(+)"

7-485(-)"

6-+5 VDC Out"

5-RLY4 Input (5V)"

4-RLY3 Input (5V)"

3-LED Output"

2-D1/Data/F2F Input"

1-D0/CLK Input

Input

Red arrow denotes direction!

of command signal

Output

LED Input and Output

6. The Cypress SPX-1300 provides additional data channels to support access control hardware such as door

strikes, tamper alarms, request to exit status, etc. These signals are sent to and from the Remote and Central units

without the need to run additional wiring."

The accessory control I/O use active low inputs. When the inputs are ﬂoating (nothing connected) the associated

output will be set to a high level. When the input is set to 0Volts (Ground) the input will activate its associated

output. All Accessory outputs are Open Collector type and will switch to Ground when activated."

Each input will have an associated output. See the following pages for a diagram of each I/O pair."

Inputs can be tested by making a jumper connection to ground and monitoring the associated output.

Altri manuali per Suprex SPX-1300

Indice

Altri manuali Cypress Estensione

Cypress

Cypress CLUX-SDI2HC Manuale utente

Cypress

Cypress Suprex SPX-5631 Manuale utente

Cypress

Cypress Suprex RF SPX-5631R Manuale utente

Cypress

Cypress Suprex SPX-5600 Series Manuale utente

Cypress

Cypress Suprex SPX-5631 Manuale utente

Cypress

Cypress Suprex WMR-9600MAN Manuale utente

Cypress

Cypress Suprex RS-485 Manuale utente

Cypress

Cypress CY3242-IOXlite Manuale utente

Cypress

Cypress CLUX-SDI2HC Manuale utente

Cypress

Cypress Suprex SPX-1300 Manuale utente

Cypress

Cypress Suprex SPX-7400 Series Manuale utente

Cypress

Cypress DPX-5500 Series Manuale utente

Cypress

Cypress CMDP-13MDPI Manuale utente

Cypress

Cypress Suprex SPX-7500 Manuale utente

Cypress

Cypress CIR-03 Manuale utente

Cypress

Cypress Suprex SPX-7200 Manuale utente

Cypress

Cypress Suprex SPX-7200 Manuale utente

Cypress

Cypress PU-515PL-KIT HDBaseT Manuale utente

Cypress

Cypress SPX-1200 Manuale utente

Cypress

Cypress DCT-32TX Manuale utente

Cypress

Cypress CA-USBHUT Manuale utente

Cypress

Cypress CIR-12 Manuale utente

Manuali Estensione popolari di altre marche

SY HDBT-60T Manuale utente

Appsys ProAudio

Appsys ProAudio ADX-16 Manuale utente

Atlona

Atlona RS232 Manuale utente

IDK

IDK OPF-TH1000-A Manuale utente

Enable-IT

Enable-IT 824WP Manuale utente

Worx

Worx Landroid RadioLink WA0864 Scheda tecnica

TP-Link

TP-Link TL-WA730RE Manuale utente

Camplex

Camplex CMX-HDMI-SFPL Manuale utente

SC&T

SC&T HE03-4K Manuale utente

Marmitek

Marmitek MegaView70 Manuale utente

Samsung

Samsung SCS-26UC4 Manuale utente

Foxun

Foxun SX-GES24 Manuale utente

MuxLab

MuxLab 500771 Manuale utente

foxunhd

foxunhd SX-AEX01 Manuale utente

TERK Technologies

TERK Technologies LFIRX2 Manuale utente

Devolo

Devolo Audio Extender Manuale

Edimax

Edimax EW-7438RPn V2 Manuale utente

Shinybow USA

Shinybow USA SB-6335T5 Manuale utente