D-CUT LT-180 Manuale utente
OPERATION MANUAL
Vinyl / LVP Flooring Cutter LT-180
www.dcutproducts.com
CUTTING AND C
2
Assembly of the Cutter
Use provided Allan wrench, screws,
nuts and bolts to assemble:
1. Blade onto the base
2. Handle
Warning:
Avoid contact with the steel teeth along
the cutting slot, which may cause
injury.
Installation of the Stopper
Insert the stopper attachment into two
metal holes as shown.
Warning:
Avoid contact with the steel teeth along
the cutting slot, which may cause
injury.
Transportation and storage
Hook the chain to the ring on the
handle and carry the cutter as shown.
3
Free Angle Cut
Remove the stopper attachment from
the cutting table. Place the material on
the table as shown, follow the line that
you draw on the material, then push
the handle down to complete the cut.
Warning:
Avoid contact with the steel teeth along
the cutting slot, which may cause
injury.
Square Cut
Insert the material between the cutting
blade and the stopper, flush with the
stopper attachment as shown and hold the
material then push handle down to
complete the cut.
Warning:
Avoid contact with the steel teeth along
the cutting slot, which may cause injury.
Lengthwise Cut
Find two holes on the table that meet
your requirement of the width you
want to cut, insert the stopper
attachment into the holes. Place the
material on the table flush against the
stopper attachment as shown, then
push the handle down to complete the
cut.
Warning:
Avoid contact with the steel teeth along
the cutting slot, which may cause
injury.
4
Part List
Parts Q’ty Parts Q’ty
1 Hex Screw M5 × 8 8 16 Head Nut M4 2
2 Spring Washer Φ5 8 17 Stopper Attachment 1
3 Washer Φ5 8 18 Steel Tooth 2
4 Rubber Feet 8 19 Rubber Pad 1
5 Front Base 1 20 Hook 1
6 Cross Bar 4 21 PVC Handle 1
7 Screw M5 × 55 1 22 Handle 2
8 Nut M5 1 23 Knurled thumb Screw M5 × 10 1
9 Flange nut M6 1 24 Blade 1
10 Rear Base 1 25 Working Table 2
11 Cross Bar End 8 26 Steel tooth Holder 2
12 Bolt M6 1 27 Shaft Shoulder Bolt M12 1
13 Chain 1 28 Flange Nut M10 1
14 Hex Screw M5 × 20 10 29 Position Pin 2
15 Hex Screw M5 × 12 16
Altri manuali D-CUT Taglierina
D-CUT
D-CUT LT-330 Manuale utente
D-CUT
D-CUT LU-215 Manuale utente
D-CUT
D-CUT XP-215 Manuale utente
D-CUT
D-CUT LP-650 Manuale utente
D-CUT
D-CUT MD-230 Manuale utente
D-CUT
D-CUT MH-330 Manuale utente
D-CUT
D-CUT TC-330 Manuale utente
D-CUT
D-CUT LT-200 Manuale utente
D-CUT
D-CUT GC-230 Manuale utente
D-CUT
D-CUT LH-320 Manuale utente
D-CUT
D-CUT MD-460 Manuale utente
D-CUT
D-CUT TC-230 Manuale utente
D-CUT
D-CUT LX-230 Manuale utente
D-CUT
D-CUT SC-230 Manuale utente
D-CUT
D-CUT MH-510 Manuale utente
D-CUT
D-CUT RC-200 Manuale utente
D-CUT
D-CUT LX-200 Manuale utente
D-CUT
D-CUT DP-340 Manuale utente
D-CUT
D-CUT PL-215 Manuale utente
D-CUT
D-CUT HC-040 Manuale utente
