D-Link DVG-2101sp Manuale utente

DVG-2101SP User Manual

DVG-2101SP VOIP TELEPHONE ADAPTER

USER MANUAL

v1.02AU

DVG-2101SP User Manual

Contents

Introduction 4

Package Contents 4

Features 5

Front Panel 7

Back Panel 8

Hardware Installation 9

Conﬁguration 12

Setup 15

Internet Setup 15

VoIP Setup 20

Time and Date 22

Advanced 23

VoIP Settings 23

DNS 35

Dynamic DNS 36

QoS 37

VPN 38

Maintenance 39

System 39

Firmware Update 43

Access Control 44

Ping Test 45

Status 46

Device Information 46

VoIP Status 47

CDR Status 48

VPN Status 49

Network Status 50

System Log 51

Help 52

Help Menu 52

Conﬁguration through IVR 53

Frequently Asked Questions 54

Technical Speciﬁcations 56

Technical Support 58

DVG-2101SP User Manual

Introduction

The D-Link DVG-2101SP VoIP Telephone Adapter links conventional telephony devices such as analog phones

or fax machines to IP networks. The DVG-2101SP includes one Ethernet port and one RJ-11 telephone jack

that provides voice communication over the IP network. It is also equipped with one PSTN (RJ-11) jack to

allow the device to connect to the PSTN line. The Ethernet port is for a DSL/Cable Modem or other WAN (Wide

Area Network) devices such as a Router or Gateway. It can be conﬁgured and monitored using a web browser.

This VoIP Telephone Adapter can reduce or eliminate long distance or inter-ofﬁce phone charges by routing

calls over the Internet or any IP network. Corporations can also enjoy the beneﬁts of network consolidation

and reduction of leased lines by relying on the Internet service providers to deliver toll-quality voice

communications over the IP networks.

With this device, you can make and receive calls from the Internet or PSTN (make only).

Package Contents

• 1 x DVG-2101SP VoIP Telephone Adapter

• 1 x CAT5 Ethernet Cable (Blue)

• 2 x RJ-11 Phone Cables (Grey)

• 1 x 12V/1.5A AC/DC Adapter

• 1 x CD-ROM with Product Documentation

- User Manual

- Quick Setup Guide

DVG-2101SP User Manual

Features

• WAN Support

- One 10/100Mbps auto-MDI/MDIX Ethernet port

- WAN Type: Static IP, Dynamic IP & PPPoE

- MAC Address Clone

- NAT Traversal: Outbound Proxy, STUN

- Dynamic DNS support: DLinkDDNS, DynDNS

- VLAN ID Tag

- QoS: IP Precedence

- NTP

• Management

- Web-based (HTTP), Telnet, and Telephone keypad conﬁguration (dial preﬁx)

- Built-in Ping Tool

- Remote ﬁrmware upgrade via TFTP, HTTP, HTTPS, and FTP

- Multi-function reset button: IVR , reset , restore factory default settings

- Password Protected - controlled Admin and User Access Authority

- Auto Provisioning:

+ Web-based Administration and Conﬁguration via Integrated Web Server

+ Telephone Key Pad Conﬁguration with Interactive Voice Prompts, Automated Provisioning &

Upgrade via HTTPS, HTTP, TFTP, FTP

- Interactive Voice Response (IVR)

- SNMP V1/V2C

• Call In & Call Out

- Voice over IP Call

- PSTN Phone Call (out only)

- IP Address Calling

- Three Way IP to IP Conference Call

• Call Features

- Call Forwarding: No Answer / Busy / Unconditional

- Call Transfer: Unattended / Attended

- Call Waiting / Call Pickup / Call Hold / Call Back On Busy / Call Return

- Three Way Calling (Media Server required)

- MWI (Message Waiting Indicator) based on LED & Tone

- DND (Do Not Disturb)

- Warm Line

- Hot Line

- Selective / Anonymous Call Rejection

- Music On Hold

- Caller ID (Type I and Type II)

- Caller ID Blocking

- Speed Dialing, Repeat Dialing

- Consultation Hold

DVG-2101SP User Manual

• Voice Functionality

- SIPv2 (RFC3261) compliance

- SIP Proxy Redundancy: Dynamic via DNS SRV, A Records Re-registration with Primary SIP Proxy

Server

- SIP Extension: Session Timer, Proxy-Require

- MD5 Authentication for SIP

- SIP NAT Keep Alive Timer

- VPN

- Flash Hook Timer

- Adaptive Jitter Buffer

- Programmable Gain Control

- In-band DTMF

- Out-of-band DTMF relay: RFC2833 / SIP Info

- DTMF

- Termination Impedance: 600 / 900 & complex Impedance

- Failover SIP Proxy server registrations

- T.30 FAX pass through, T.38 real time FAX relay

- Caller ID: DTMF, FSK-Bellcore, FSK-ETSI detection and generation by country select

- Telephone book

- Voice Codec Feature: G.711 u-law/a-law, G.723.1/iLBC (optional), G.726, G.729.A/B

- VAD (Voice Activity Detection)

- CNG (Comfort Noise Generation)

- G.165/G.168 Echo Cancellation

- Silence Suppression & Detection

DVG-2101SP User Manual

Front Panel

Power LED

This LED will light solid when the

device ﬁnishes a self-test and

booting up. This LED will ﬂash

during device self-test and booting

and light off if the self-test fails.

Phone LED

This LED will light solid when the

telephone is off-hook. A fast blinking

LED indicates an incoming call and

a slow blinking LED indicates a

message is waiting. This LED will

light off if the phone connected to

the phone port is on-hook.

WAN LED

This LED will light solid when a connection

is established and blink to indicate activity.

If this LED does not light up when a cable is

connected, verify the cable connections and

make sure your devices are powered on.

This LED will light solid if the phone

account registers successfully. This

LED will ﬂash during registering and

light off if registering fails.

Provision LED

This LED will light up solid if the

device provisions successfully. The

LED will ﬂash during provisioning

and will be off if provisioning fails.

Line LED

This LED will light solid when

a connection is established

and blink to indicate activity.

DVG-2101SP User Manual

Back Panel

WAN Port

Connects to your

broadband modem using

an Ethernet cable.

Power Receptor

Connects to the provided

power adapter.

Reset Button

Using a paper clip to:

1. Press 1-2 seconds to enable IVR.

2. Press 4-6 seconds to reset this unit.

3. Press 8-10 seconds to restore this

unit’s factory default settings.

Line Port

Connects to the PSTN line

outlet using a standard

phone cable (RJ-11).

Phone Port

Connects to your phone

using a standard phone

cable (RJ-11).

DVG-2101SP User Manual

Hardware Installation

Connecting the DVG-2101SP Directly to a Modem in Bridge Mode

If your computer connects directly to a DSL or Cable modem and does not connect to a router, follow the

steps below to install your DVG-2101SP.

Note: If your modem only has the one Ethernet port and it is being used by your computer then you will

require a Router/Gateway, please see the next page for details on connecting using a Router/Gateway..

1. Turn off your computer.

2. Disconnect the power to your Cable/DSL modem (unplug or turn off the power switch).

3. Unpack the Ethernet cable (blue) that comes with DVG-2101SP. Attach one end of the Ethernet cable

(blue) provided in this package to a LAN or Ethernet port on your Cable/DSL modem. If there are no

Ethernet ports available on your modem, you should include a Router/Gateway in your network setup

(see diagram on the next page).

4. Attach the other end of the provided Ethernet cable to the WAN port of the DVG-2101SP.

5. Attach one end of the provided phone cable (grey) to a standard analog telephone.

6. Attach the other end of the phone cable to the PHONE port on the rear panel of the DVG-2101SP.

7. Attach one end of the provided phone cable (grey) to a PSTN wall socket.

8. Attach the other end of the phone cable to the LINE port on the rear panel of the DVG-2101SP.

9. Reconnect the power to the Cable/DSL modem (plug in or turn on the power switch).

10. Unpack the 12V DC power adapter that comes with the DVG-2101SP. Connect the power adapter to the

power connecter on the DVG-2101SP.

11. Connect the other end of the power adapter to an available electrical outlet (wall socket or surge

protector).

12. Restart your PC.

DVG-2101SP User Manual

Connecting the DVG-2101SP Behind a Router (Recommended)

If you wish to connect your DVG-2101SP behind a router, follow the steps below. After the steps are

completed, your setup should look similar to the diagram below.

1. Turn off your computer.

2. Disconnect the power to the Cable/DSL modem (unplug the modem or turn off the power switch).

3. Disconnect the power to your existing router (unplug the router or turn off the power switch).

4. Unpack the Ethernet cable (blue) that came with the DVG-2101SP.

5. Attach one end of this Ethernet cable to the WAN port on the rear of the DVG-2101SP.

6. Attach the other end of this Ethernet cable to a LAN port on your existing router.

7. Be sure that the Ethernet cable that is plugged into the WAN port of your existing router is still plugged

into your Cable/DSL modem.

8. Unpack the phone cable (grey) that came with the DVG-2101SP. Attach one end of this cable to a

standard analog telephone.

9. Attach the other end of this cable to the PHONE port on the rear of the DVG-2101SP.

10. Attach one end of the provided phone cable (grey) to a PSTN wall socket.

11. Attach the other end of the phone cable to the LINE port on the rear panel of the DVG-2101SP.

12. Unpack the 12V DC power adapter that came with the DVG-2101SP.

13. Connect the power adapter to the power connecter on the DVG-2101SP.

14. Connect the other end of the power adapter to an available electrical outlet (wall socket or surge

protector).

15. Reconnect the power to the Cable/DSL modem (plug in or turn on the power switch).

16. Reconnect the power to your existing router (plug in or turn on the power switch).

17. Restart your PC.

By default the unit is already conﬁgured to work behind a router. Be sure to change your computer’s IP

settings to DHCP (to automatically be assigned an IP address from the DVG-2101SP) regardless of what

type of Internet connection you have. (Please refer to your Network Interface Card’s manual for more detailed

information.)

Altri manuali per DVG-2101sp

Indice

Altri manuali D-Link Adattatore

D-Link

D-Link DWA-131 Manuale utente

D-Link

D-Link DFE-528TX Manuale utente

D-Link

D-Link DHP-P701AV Manuale utente

D-Link

D-Link DWL-G650 - AirPlus Wireless 802.11b 11Mbps/802.11g 54Mbps PC... Manuale utente

D-Link

D-Link DHP-501AV Manuale utente

D-Link

D-Link DFE-528TX Manuale utente

D-Link

D-Link DHP-310AV Manuale utente

D-Link

D-Link DWA-192 Manuale utente

D-Link

D-Link DFE-530TX Manuale utente

D-Link

D-Link DWL-AG132 Manuale operativo

D-Link

D-Link DVG-2101sp Manuale utente

D-Link

D-Link Air DWL-610 Manuale utente

D-Link

D-Link DHP-308AV Manuale utente

D-Link

D-Link DWA-130 Manuale utente

D-Link

D-Link DWA-142 Manuale utente

D-Link

D-Link AirPlus DWL-810 Manuale utente

D-Link

D-Link DBT-122 Manuale utente

D-Link

D-Link DWA-171 Manuale utente

D-Link

D-Link DHP-601AV Manuale utente

D-Link

D-Link DWA-137 Manuale utente

D-Link

D-Link DFE-500FX Manuale utente

D-Link

D-Link DWA-182 Manuale utente

D-Link

D-Link DHP-312 Manuale utente

D-Link

D-Link DWL-G820 - AirPlus Xtreme G Manuale utente

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente

RCA

RCA AH57R Manuale utente