D-Link DMC-1001 - Power Supply - hot-plug Manuale utente

DMC-1001

Redundant Power Supply

User’s Guide

Rev. 01 (JAN. 2002)

Printed In Taiwan

RECYCLABLE

INTRODUCTION

Thank you for choosing the DMC-1001 Redundant

Power Supply of Chassis-Based Media Converter.

When the chassis is equipped with two power supplies,

both power supplies are switched on and share the

current load. In case that one of them should fail, the

other will instantaneously take 100% of the load

without any loss. Similarly, if one power supply is

removed from servicing, it can be switched off and

removed while the chassis continues functioning.

Product Features

9Efficiency: The efficiency is higher than 70% by

measured at nominal line and rated load.

9Protection: Over voltage protection; short circuit

protection.

9Power sharing and redundancy.

9Fan failure Signal: The power supply will provide

a predictive fan failure signal that detects a failure

based on reduced fan RPM.

INSTALLATION

Step 1: Connect the supplied AC power cord to the back of the

chassis.

Step 2: Attach the plug into a standard AC outlet with a voltage

range from 100~240Vac.

Step 3: Turn on the chassis system by flipping the switch beside the

receptacle to ON position. The LED on the front panel of

power supply will come on then.

.Installing and Removing the Power Supply

zTo remove a power supply out the chassis, you have to loose

the hand screw counter clockwise and pull out the power

supply from the chassis.

zTo install a power supply to the chassis, you have to fasten

the hand screw clockwise and slide in the power supply to

the chassis.

Youcanslide inand outthepowersupplyfrom thebay,

fastenorloose thehand screwclockwise orcounter

clockwise byusing hand orscrewdriver.

If the Chassis System needs to work alone, you can

stick up four Rubber foot below the chassis!

Attention!

SPECIFICATIONS

Power Supply

Input Voltage: 85VAC(60Hz)/264VAC(50Hz) label:

110V-240V

Output

Voltage: +12V

Power

Consumption 150 watts. (max.)

Dimension 185 x 160 x 85 mm

Temperature Operating: 0°~40°C,

Storage: -10°~50°C

Humidity Operating: 10% ~ 90%,

Storage: 5% ~ 90%

Overload

Protection

All outputs protected from short circuit

condition, automatic recovery

Emissions FCC Class A, CE Mark Class A,

VCCI Class A

Safty

Standard

UL 1950CSA

CSA 22.2 No.234

Altri manuali per DMC-1001 - Power Supply - hot-plug

Indice

Altri manuali D-Link Alimentazione elettrica

D-Link

D-Link DMC-1001 - Power Supply - hot-plug Manuale utente

D-Link

D-Link DPS-520 Manuale utente

D-Link

D-Link mydlink DSP-W215 Manuale utente

D-Link

D-Link DPS-300 Manuale utente

D-Link

D-Link DPS-200A Manuale utente

D-Link

D-Link DPS-520 Manuale utente

D-Link

D-Link DIS-PWR40AC/RU Manuale utente

D-Link

D-Link DIS-PWR180AC/RU Manuale utente

D-Link

D-Link RPS DPS-200 Manuale utente

D-Link

D-Link DCS-80-5 Manuale utente

D-Link

D-Link DGS-6604-SK Manuale utente

D-Link

D-Link DPS-510 Manuale utente

D-Link

D-Link mydlink DSP-W215 Manuale utente

D-Link

D-Link DMC-1001 - Power Supply - hot-plug Manuale utente

Manuali Alimentazione elettrica popolari di altre marche

Monacor

Monacor PS-12CCD Manuale utente

VOLTIMA

VOLTIMA MagicBox 15 Manuale utente

Agilent Technologies

Agilent Technologies 6032A Manuale utente

Miller

Miller Auto Deltaweld 452 Manuale utente

BCP

BCP PUOUBK Foglio di istruzioni

HC 2210 Manuale utente

Puls

Puls CT5.241 Manuale utente

OCZ

OCZ ZX1250W Manuale utente

iseg

iseg ECH 238 Manuale utente

Power

Power XXL A Series Manuale utente

Agilent Technologies

Agilent Technologies 6631B Manuale utente

Renogy

Renogy PHOENIX 300 Manuale utente

HP 6200B Manuale di servizio

Epson

Epson Stylus Scan 2500 Manuale operativo

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuale utente

Puls

Puls MiniLine ML50.100 Manuale utente

Puls

Puls AS-Interface SLA4.100 Manuale utente

Kenwood

Kenwood PS-60 Manuale utente