D-Link DCS-6616 Manuale utente
Documentation also available on
CD and via the D-Link Website
Quick Installation Guide
Краткое руководство по установке
Guía de Instalación Rápida
Guia de Instalação Rápida
快速安裝指南
Petunjuk Pemasangan Cepat
This document will guide you through the
basic installation process for your new D-Link
Network Camera.
DCS-6616
Quick Installation Guide
12X Speed Dome Network Camera
D-Link DCS-6616 Quick Install Guide
2
ENGLISH
DCS-6616 Quick Install Guide
This installation guide provides basic instructions for installing the DCS-6616 Network
Camera on your network. For additional information about how to use the camera,
please see the User’s Manual which is available on the CD included in this package or
from the D-Link support website.
Installation Steps
1. Verify the package contents against the list below.
2. Hardware Overview
3. Hardware Installation
4. Conguration with Wizard
1. Package Contents
DCS-6616 Network Camera
Manual and Software on CD-ROM
Quick Install Guide
Power Adapter
AV & Power Cables
Mounting Bracket and Screws
If any of the above items are missing, please contact your reseller.
Safety Notice:
Installation and servicing should be done by certied technicians so as to conform to all
local codes and prevent voiding your warranty.
D-Link DCS-6616 Quick Install Guide
3
ENGLISH
2. Hardware Overview
Camera Lens
Motorized varifocal
autofocus lens
Ethernet 10/100
RJ45 Socket
Reset Button
Press and hold the
reset button for
approximately 10
seconds to reset
to factory default
settings
Cable Connector Socket
D-Link DCS-6616 Quick Install Guide
4
ENGLISH
3. Mounting Instructions
Detach the Decoration Ring from
the Hard Ceiling Mount Bracket.
Align the three holes on the
Mount Bracket, mark the screws
locations on the ceiling
Drill three pilot holes into the
ceilling and hammer the plastic
anchors into the holes
Fix the Mount Bracket with three screws
D-Link DCS-6616 Quick Install Guide 5
ENGLISH
Insert the xing plate into the
groove as shown below
Align the three holes to screw
the xing plate to the dome bas
Connect the cable connector and
Ethernet cable to the dome base
Align plate A and plate B, then
use those three hole to hook the
Network Camera on the ceiling
mount bracket
A
B
D-Link DCS-6616 Quick Install Guide
6
ENGLISH
Tighten the screw on the xing plat
Align the three holes to mount the decoration ring.
D-Link DCS-6616 Quick Install Guide 7
ENGLISH
General Connection Using 12 V DC Power Adapter
1. Connect the network camera to a hub via an Ethernet cable.
2. Connect the supplied power cable from the camera to a power outlet.
D-Link DCS-6616 Quick Install Guide
8
ENGLISH
4. Conguration with Wizard
Click Setup Wizard to begin the installation.
Insert the DCS-6616 CD into your computer's CD-ROM drive to begin the installation. If
the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start
automatically, click Start > Run. Type D:\autorun.exe, where D: represents the drive
letter of your CD-ROM drive.
After clicking Setuop Wizard, the following window will
open.
Click Next to continue.
Click Yes to accept the License Agreement.
Click Finish to complete the installation.
To start the installation process, click Next.
Note: The installation may take several minutes to
nish.
D-Link DCS-6616 Quick Install Guide 9
ENGLISH
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Take a moment to conrm your settings and click Restart.
Select DHCP if your camera obtains an IP address
automatically when it boots up. Select static IP if the
camera will use the same IP address each time it is
started.
Click Next, to proceed to the next page.
Enter the Admin ID and password. When logging in for
the rst time, the default Admin ID is admin with the
password left blank.
Click Next, to proceed to the next page.
The Setup Wizard will appear and display the MAC
address and IP address of your camera(s). If you have
a DHCP server on your network, a valid IP Address
will be displayed. If your network does not use a
DHCP server, the network camera's default static IP
192.168.0.20 will be displayed.
Click the Wizard button to continue.
D-Link DCS-6616 Quick Install Guide
10
ENGLISH
Click on the D-Link Setup Wizard SE icon that was
created in your Windows Start menu.
Start > D-Link > Setup Wizard SE
Viewing Camera via Web Browser
This section shows your camera’s live video. You
can select your video prole and view or operate
the camera. For additional information about web
conguration, please refer to the user manual
included on the CD-ROM or the D-Link website.
Enter admin as the default username and leave the
password blank. Click OK to continue.
Select the camera and click the button labeled "Link"
to access the web conguration.
The Setup Wizard will automatically open your web
browser to the IP address of the camera.
Altri manuali per DCS-6616
4
Indice
Lingue:
Altri manuali D-Link Telecamera di sicurezza
D-Link
D-Link DCS-6314 Manuale utente
D-Link
D-Link DCS-2210 Manuale utente
D-Link
D-Link DCS-6314 Manuale utente
D-Link
D-Link DCS-2330L Manuale utente
D-Link
D-Link DCS-6500HLV2 Manuale utente
D-Link
D-Link Mydlink DCS-8200LH Manuale utente
D-Link
D-Link DCS-5020L Manuale utente
D-Link
D-Link DCS-6500LHV2 Manuale utente
D-Link
D-Link DCS-7513 Manuale utente
D-Link
D-Link DCS-5610 Manuale utente
D-Link
D-Link DCS-3710 Manuale utente
D-Link
D-Link SECURICAM NETWORK DCS-5300 Manuale utente
D-Link
D-Link SECURICAM DCS-5605 Manuale utente
D-Link
D-Link DCS-2630L Manuale utente
D-Link
D-Link DCS-4802E Manuale utente
D-Link
D-Link DCS-4633EV Manuale utente
D-Link
D-Link DCS-6915 Manuale utente
D-Link
D-Link DCS-5010L Manuale utente
D-Link
D-Link SECURICAM NETWORK DCS-5300 Manuale utente
D-Link
D-Link DCS-942L Manuale utente
