D-Link DAP-1250 Manuale utente

DAP-1250

System Requirements

• A Network with 802.11g/b wireless devices

Package Contents

• Access Point

• Antenna

Please follow below table to install DAP-1250 , otherwise, it may be illegal.

Antenna No. Type Frequency Band Gain (dBi) Conntector ｃable

Length cable

loss

ANT24-0800 Dipole Omni 2400MHz

- 2500MHz 8 N female 7m 6

ANT24-1201 Yagi Directional 2400MHz

- 2500MHz 12 N female or

SMA femal 11.7m 10

ANT24-1400 Panel Directional 2300MHz

- 2500MHz 14 N female 14m 12

ANT24-1800 Panel Directional 2400MHz

- 2500MHz 18 N female 18.7m 16

ANT24-1801 Yagi Directional 2400MHz

- 2700MHz 18 N female 18.7m 16

ANT70-0800 Dipole Omni

2400MHz

- 2500MHz

4900MHz

- 5470MHz

8 N Jack 7m 6

ANT70-0801 Dipole Omni

2400MHz

- 2500MHz

4900MHz

- 5470MHz

8 N Jack 7m 6

ANT70-1000 Panel Directional

2400MHz

- 2500MHz

4900MHz

- 5875MHz

10 N Jack 7m 6

WSS002 1/4 入Dipole 2400MHz

- 2500MHz 2 RP-SMA(M) 0 0

N/A Printed 2400MHz

- 2500MHz 2 N/A N/A N/A

• CD-ROM (with software, manual, and warranty)

• Ethernet Cable

• 5V/2A Power Adapter

• Rubber Feet

• A Network with 802.11g/b wireless devices

Before You Begin

It’s best to use a computer (with an Ethernet adapter) that is connected to a

switch or router for configuring the DAP-1250. The default IP address for the

DAP-1250 is 192.168.0.50 with a Subnet Mask of 255.255.255.0.

You will need to assign your computer a Static IP address within the same

range as the DAP-1250’s IP address for the purpose of configuring the

DAP-1250. See the Appendix if you need assistance in assigning a Static IP

address for your network adapter.

Installation Considerations

D-Link wireless devices allow you access your network using a wireless

connection from virtually anywhere within the operating range of your wireless

network. Keep in mind, however, that the number, thickness and location of

walls, ceilings, or other objects that the wireless signals must pass through,

may limit the range. Typical ranges vary depending on the types of materials

and background RF (radio frequency) noise in your home or business. The key

to maximizing wireless range is to follow these basic guidelines:

1. Keep the number of walls and ceilings between the D-Link access point

and other network devices to a minimum - each wall or ceiling can reduce

your adapter’s range from 3-90 feet (1-30 meters.) Position your devices

so that the number of walls or ceilings is minimized.

2. Be aware of the direct line between network devices. A wall that is 1.5

feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet (1

meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick!

Position devices so that the signal will travel straight through a wall or

ceiling (instead of at an angle) for better reception.

3. Building Materials make a difference. A solid metal door or aluminum

studs may have a negative effect on range. Try to position access points,

wireless routers, and computers so that the signal passes through drywall

or open doorways. Materials and objects such as glass, steel, metal, walls

with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete

will degrade your wireless signal.

4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical

devices or appliances that generate RF noise.

5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as

ceiling fans, lights, and home security systems), your wireless connection

may degrade dramatically or drop completely. Make sure your 2.4GHz

phone base is as far away from your wireless devices as possible. The

base transmits a signal even if the phone in not in use.

Connecting the DAP-1250 Wireless

Access Point to Your Network

A. First, connect the power adapter to the receptor at the back panel of the

DAP-1250 and then plug the other end of the power adapter to a wall outlet

or power strip. The Power LED will turn ON to indicate proper operation.

B. Insert one end of the cable to the Ethernet port on the back panel of the

DAP-1250 and the other end of the cable to your network (switch or router).

Note: You also have the option of connecting the DAP-1250 directly to the

computer that will be used for configuration. The Link LED light will illuminate

to indicate a proper Ethernet connection.

C. The DWL-G650 AirPlus Xtreme G Wireless Cardbus Adapter and the

DWL-G520 AirPlus Xtreme G Wireless PCI Adapter will connect, out of the box,

with the DAP-1250, using their default wireless settings. Computers with

802.11b wireless adapters can also connect to the DAP-1250.

Setup Wizard

1.Open your Web browser and type http://192.168.0.50 into the

URL address box. Then press the Enter or Return key.

2.Type admin for the username and leave the password field blank.

Click OK

3. Once you have logged in, the Home screen will appear. Click Run Wizard

4. Then check next and follow the next steps

Step 1 - Set up your new password.

You have the option to establish a

password.

Click Next

Step 3 - Encryption

The DAP-1250 is capable of two levels

of wireless encryption WEP and

WPA-PSK. By default the encryption is

disabled. You can change the

encryption settings for more secure

wireless communication.

Click Next

Then Click Restart Your Setup is Complete!

Technical Support

D-Link’s website contains the latest user documentation and software

updates for D-Link products.

U.S. and Canadian customers can contact D-Link Technical Support

through our website or by phone.

D-Link and the D-Link logo are registered trademarks of D-Link Corporation or

its subsidiaries in the United States and other countries. Other trademarks are

the property of their respective owners. Maximum wireless signal rate derived

from IEEE Standard 0 .11g specifications. Actual data throughput will vary.

Network conditions and environmental factors, including volume of network

traffic, building materials and construction, and network overhead, lower actual

data throughput rate. Environmental factors may adversely affect wireless

signal range. Visit www.dlink.com for more details.

Industry Canada Statement

This device complies with RSS-210 of the Industry Canada Rules. Operation is

subject to the following two conditions:

1) this device may not cause interference and

2) this device must accept any interference, including interference that may

cause undesired operation of the device

This device has been designed to operate with an antenna having a maximum

gain of .. 2dBi.

Antenna having a higher gain is strictly prohibited per regulations of Industry

Canada. The required antenna

impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its

gain should be so chosen that the EIRP is not more than required for

successful communication.

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one of the

following measures:

Indice

Altri manuali D-Link Router wireless

D-Link

D-Link Ethernet Broadband Router DIR-100 Manuale utente

D-Link

D-Link Ethernet Broadband Router DIR-100 Manuale utente

D-Link

D-Link AC1200 Manuale utente

D-Link

D-Link DIR-615 - Wireless N Router Manuale utente

D-Link

D-Link EXO DIR-X6060 Manuale utente

D-Link

D-Link Xtreme N Duo DAP-1555 Manuale utente

D-Link

D-Link DIR-628 - RangeBooster N Dual Band Router... Manuale utente

D-Link

D-Link DSL-2750E Manuale utente

D-Link

D-Link Express EtherNetwork DI-604+ Manuale utente

D-Link

D-Link DSL-2730R Manuale utente

D-Link

D-Link Ethernet Broadband Router DIR-100 Manuale utente

D-Link

D-Link DWR-116 Manuale utente

D-Link

D-Link DIR-619L Manuale utente

D-Link

D-Link EXPRESS ETHERNETWORK VDI-604 Manuale utente

D-Link

D-Link DAP-1620 Manuale utente

D-Link

D-Link DI-711 - Gateway Manuale utente

D-Link

D-Link DSL-2740B Manuale utente

D-Link

D-Link GO-RT-N300 Manuale utente

D-Link

D-Link SharePort DIR-825 Manuale utente

D-Link

D-Link Wireless N900 Manuale utente

D-Link

D-Link DKT-110 Manuale utente

D-Link

D-Link DIR-524 Manuale utente

D-Link

D-Link dlinkgo GO-RTW-N300 Manuale utente

D-Link

D-Link DIR-604 Manuale utente

Manuali Router wireless popolari di altre marche

Milesight

Milesight UG67 Manuale utente

Airlogic

Airlogic AirSync Class 1 Manuale del proprietario

Samsung

Samsung WCH730B Manuale utente

TELEFONICA

TELEFONICA USB Adapter Manuale utente

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuale utente

Askey

Askey RAC2V1K Manuale utente

Alloy

Alloy WLF2454AP-S Manuale utente

TP-Link

TP-Link TL-WR542G Manuale utente

NETGEAR

NETGEAR WNR2000v4 Manuale utente

Hama

Hama 53120 Manuale utente

Intellinet

Intellinet 524582 Manuale utente

Asus

Asus RT-N10P Manuale utente

Sapido

Sapido GR297n Manuale utente

Asus

Asus DSL-N55U Manuale utente

AMTC

AMTC WR7502 Manuale utente

Compaq

Compaq CP-2W - iPAQ Connection Point Manuale utente

SMC Networks

SMC Networks WBR14-N2 FICHE Manuale utente

Draytek

Draytek Vigor2120 Series Manuale utente