Da-Lite TENSIONED EXECUTIVE ELECTROL Manuale utente

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574/267-8101

800-622-3737

Fax: 574/267-7804

http:// www.da-lite.com

e-mail: [email protected]

POWER

PRESENTATION PRODUCTS

The

Instruction Book for

TENSIONED EXECUTIVE®ELECTROL®

PRE-INSTALLATION

INSTALLATION

1. Position screen under mounting location with the case opening down.

2. Install screen by raising unit into position between joists at one end only. Install one lag screw in each mounting

bracket. Secure opposite end. Support center of the screen using the brackets.

3. Level unit lengthwise with a carpenter’s level and a plum level.

CAUTION! Do not secure access door or seal in unit until screen has been secured in position and properly tested for satisfac-

tory operation. Do not fit unit so tightly that the screen surface drop door binds. Door drops by gravity only.

▲

1. Carefully unpack screen and remove outer wrapping from case.

2. Remove instructions cover and please read instructions. (Fig. 1)

3. Remove fabric and cardboard strips from access door. (Fig. 1)

4. Remove access door by gently prying from edge of box toward the fabric door.

5. FOR TYPE 3 INSTALLATION ONLY. Remove wood strips along bottom of screen case.

NOTE: Screen surface is not centered in box. Screen surface is 25" from motor end.

6. Make sure to recheck measurements of screen location before installation.

7. Remove, reverse, and remount center support brackets.

CASE FABRIC

STRIP

ACCESS DOOR CARDBOARD

STRIP

FABRIC DOOR

INSTRUCTION COVER

FIGURE 1

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions should always be followed, in-

cluding the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at least equal to that of the

appliance should be used. Cords rated for less amperage than the appliance may over-

heat.

4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an autho-

rized service dealer when repair work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the manufacturer may cause a

risk of fire, electric shock, or injury to persons.

SAVE THESE INSTRUCTIONS

The picture surface drop, and the opening and closing of the fabric door, are controlled automatically by limit switches

which have been preset at Da-Lite. When the picture surface is moving upward, it is controlled by a limit switch that

shuts off when the door closes. The height for tensioned screens are adjusted at Da-Lite, changing the height of screen

will change the tension on fabric and cause the screen to hang improperly. Do not adjust.

ACCESS DOOR INSTALLATION

SCREEN ADJUSTMENT

1. Press switch “down” so that fabric door opens (Fig. 2).

2. Remove screws (2) located on each bumper bracket.

NOTE: The access door is slotted on one edge, permitting the slotted section to fit over the access panel clips on inside of case.

3. Place access panel so slot can be pushed over clips. Holes in access panel brackets should align with bumper

bracket holes.

4. Replace screws.

5. Make sure there is approximately 3⁄16" clearance around access door. Keep paint, plaster, tile or mastic out of hinge.

Fit access panel so it can be removed for maintenance.

CROSS SECTION

BUMPER

BRACKET

ACCESS PANEL SCREW

(PAINTED)

PICTURE

SURFACE

ACCESS PANEL

FABRIC DOOR

ACCESS

PANEL CLIP

FALSE TOP

FIGURE 2

INSTALLATION

4. If you are going to cover screen door with paneling or other materials, allow access (suitable holes or a plug) to

screws for servicing.

5. Picture surface should hang freely. (Fig. 2) Remove any tape left hanging on back of fabric. Bottom edge should be

positioned between bottom edge of case and center of roller.

6. Install electrical hook up that applies to your unit.

7. Test installation by carefully running picture surface “up” and “down” several times. Be prepared to stop screen.

Fabric door must open freely to 90˚.

8. Make sure picture surface, when rolled down, has a full wrap around roller. No part of roller should be exposed.

Fabric door and picture surface will drop simultaneously when switch is pressed “down”. Door will close simultane-

ously with picture surface as picture surface rolls into case.

TENSIONED EXECUTIVE ELECTROL INSTALLATION

SUGGESTED METHODS OF INSTALLATION

TYPE 1 & 2

Offset mounting, recessed above ceiling, for plaster,

dry wall or paneling. Door painted same finish as ceiling.

TYPE 1 & 2

Allow 1/8" min. clearance all around surface door.

Flush mounting, recessed above ceiling. For use

with 1/4" max. paneling or installation in existing ceil-

ing using molding around door.

TYPE 3

Allow 1/4" min. clearance all around surface door.

Extended mounting, recessed above ceiling. For

use with acoustical or other ceiling tile 3/4" thick laid

over door.

3 1/2"

12 1/16"

9 1/2"

2 3/16"

4 1/2"

FALSE TOP

MOUNTING

BRACKETS

3/16" THICK

22"

LENGTH OF FABRIC WIDTH

+ 28 3/4", ALL SIZES

“L” BRACKET

ELECTRICAL

OUTLET

NOTE: Paint the same as doors

and ceiling or remove and

replace with ceiling tile.

INCLUDING MOUNTING BRACKETS

9 7/8"

9 1/2"

CEILING

TILE

3/4"

3/8" APPROX.

12 1/16"

FILLER

BLOCK

3/4"

FALSE TOP

1/4" MAX.

4 3/4"

1/8"

2 1/2"

1/4"

PICTURE

SURFACE

MOUNTING

BRACKETS

FALSE TOP

SURFACE DOOR

ACCESS DOOR

3/4"

11 5/16"

1/4" x 1" SCREW

& NUT INSERT

DRYWALL SCREW

“L” BRACKET

12 1/16"

1/4" x 2"

LAG SCREW

FALSE TOP

SHIM

TENSIONED EXECUTIVE ELECTROL INSTALLATION

BLACK

BLACK (UP)

BLACK

BLUE

# Z97F9036

7.5 UF ± .06%

440 V.A.C.

50/60 HZ

UP LIMIT SWITCH

(OPERATED BY DOOR)

CAPACITOR

BROWN

(DOWN)

DOWN LIMIT SWITCH

SOLENOID SWITCH

COMMON

MOTOR: 220/240V.A.C. 50 HZ 1/10 HP INTERMITTENT

DUTY WITH AUTO-RESET THERMAL PROTECTOR

INTERNAL

WIRING

EXTERNAL WIRING

TO BE COMPLETED

BY INSTALLER

JUNCTION BOX MOUNTED IN

SCREEN CASE, IN WHICH INTERNAL

WIRING TERMINATES IN

BLACK, BROWN, & BLUE.

BLUE

WHITE

BROWN

DOWN

ADJ.

DOWN

IN MULTIPLE CONTROL INSTALLATION

THIS SWITCH IS REPLACED BY

THE LOW VOLTAGE CONTROL.

BROWN/YELLOW

DOWN

OFF BROWN AC HOT

BLUE AC COMMON

220/240V. AC 50HZ.

2 AMP. MAX

BLUE JUMPER WIRE

JUNCTION

BOX

REAR VIEW OF DPDT.

WITH CENTER OFF.

ROCKER

SWITCH

(GROUND) GREEN/YELLOW

BLACK

RED (UP)

BLUE

BLACK

WHITE

RED

UP LIMIT SWITCH

(OPERATED BY DOOR)

CAPACITOR

BLACK

(DOWN)

DOWN LIMIT SWITCH

DOOR SOLENOID LIMIT SWITCH

WHITE (COMMON)

MOTOR: 120V.60 CYCLES

1/10 HP INTERMITTENT DUTY WITH

AUTO-RESET THERMAL PROTECTOR

INTERNAL

WIRING

EXTERNAL WIRING

TO BE COMPLETED

BY INSTALLER

JUNCTION BOX, MOUNTED IN

SCREEN CASE, IN WHICH INTERNAL

WIRING TERMINATES IN WHITE,

BLACK AND RED LEADS

WHITE

DOWN

ADJ.

BLACK (DOWN)

RED (UP)

IN MULTIPLE CONTROL INSTALLATIONS THIS

SWITCH IS REPLACED BY THE LOW-VOLTAGE

CONTROL, OPERATED FROM PUSH-BUTTON

STATIONS.

BLACK WITH YELLOW

DOWN

OFF AC HOT

AC COMMON

120VAC 60HZ.

1 AMP. MAX

SIDE VIEW OF

SWITCH & BOX

GREEN

(GROUND)

BLACK

BLUE

RED

OPERATING SWITCH, SWITCH BOX,

AND PLATE FURNISHED WITH

SCREEN. (SPDT) WITH CENTER OFF)

THIS SWITCH CANNOT BE USED WITH L.V.C.

SOLENOID

120V WIRING DIAGRAM

220 / 240V

WIRING DIAGRAM

BLACK

TROUBLESHOOTING

SYMPTOM

1. Screen will not operate or will not

go “down”.

Motor does not hum.

2. Motor hums.

CAUSE

(a) Blown fuse.

(b) Tripped circuit breaker.

switch.

(d) Improper wiring to junction box in

screen.

NOTE: Use low voltage control (LVC)

electrical checklist for either 1- or 3-

button control.

Defective wall switch.

Defective LVC unit.

(e) Thermal overload tripped (exces-

sive overheating).

(f) Burned out motor winding.

(g) Defective limit switch.

(a) Temporary fabric binding.

(b) Shipping bracket not removed.

SOLUTION

(a) Replace fuse.

(b) Reset circuit breaker.

tions. Correct any improper

connections. Check for power.

“Down” Position

Check for power across black

and white leads.

“Up” Position

Check for power across red and

white leads.

(d) “Down” Position

Check for power at black and

white leads.

“Up” Position

Check for power at red and

white leads.

Shut power “off” at breaker.

Remove wall switch and check

for broken or loose connection.

Replace if defective.

Check LVC electrical checklist.

(e) Let motor cool down for 15 min-

utes. Try again.

(f) Disconnect motor leads and

check for continuity between

black and white wires for “down”

position. Check for continuity be-

tween red and white wires for

“up” position. Replace gear motor

if either combination shows an

open circuit.

(g) Disconnect “down” limit switch

from circuit. Check for continuity.

Switches are normally closed and

open on contact. Replace if de-

fective.

(a) With power “off,” turn roller by

hand to free binding.

(b) Remove shipping bracket and

wooden wedge.

TROUBLESHOOTING

SYMPTOM

3. Screen will not move “up.”

Motor does not hum.

Motor hums.

CAUSE

(a) No power between red and

white leads in junction box.

Check LVC. See above.

(b) Thermal overload tripped (acts as

a breaker).

(d) Temporary fabric binding.

(e) Burned out capacitor.

(f) Broken wire or loose connection

in “up” position (red and white

leads).

SOLUTION

(a) Check fuse. Reset circuit breaker.

Correct improper wiring.

(b) Let motor cool for 15 minutes.

Try again.

and white motor leads. Replace

motor if there is power.

(d) With power “off,” turn roller by

hand to free binding.

(e) Replace capacitor.

(f) Secure connection or replace

wire.

4. Screen starts upward and door

closes immediately shutting off

motor.

(a) Defective solenoid limit switch.

Solenoid pin not retracting.

(b) Defective solenoid.

(a) Manually retract pin a few times.

(b) Check for power to the solenoid

terminals. If there is power, re-

place solenoid.

Check blue wire between sole-

noid switch and solenoid. It is

either crimped or broken. Repair

or replace.

6. Clicking noise in each downward

revolution.

(a) Non-energized solenoid.

NOTE: There should be three clicks.

(a) Check for power to solenoid.

(b) Replace solenoid.

7. Loud buzzing noise. (a) Solenoid not fully retracting. (a) Check for foreign object caught

in solenoid. Remove object.

Tighten 4 mounting screws.

Check for pin binding.

8. Door closes on fabric, leaving 15"

to 20" left hanging out.

(a) Lost roller wrap. (a) See installation instructions.

5. Fabric door does not fully open.

Screen runs.

NOTE: Remember, door must open by

gravity.

(a) Door binding. Plaster, paint or ad-

hesive can cause the hinge to

stick.

(b) Case may be put into a bind dur-

ing installation.

fabric door on new installations.

(a) Clean hinge and apply oil.

(b) Tighten or loosen lag screws

located on back of case.

TROUBLESHOOTING

SYMPTOM

9. Screen jammed. Will not operate,

motor hums, door open, closing

mechanism detached from door.

CAUSE

(a) Closing mechanism detached

from door, allowing it to jam into

box.

SOLUTION

(a) After securing fabric to roller,

loosen set screws on motor gear

and manually rotate solenoid

assembly back over top of roller

into position, then reattach door.

Match flats on motor drive shaft

to gear set screws and tighten.

10. Scraping or grinding noise. (a) If metal shipping bracket is left

attached to screen, it may be rub-

bing on motor end of roller.

(a) Remove shipping brace.

12. Incorrect down limit switch

setting.

(a) Lost roller wrap.

(b) Limit switch out of adjustment.

(a) See installation instructions.

(b) See door closure and timing

instructions.

13. Door closes and screen contin-

ues to run upward.

(a) Door limit out of adjustment.

(b) Door limit switch is shorted.

(a) Loosen nut holding limit switch.

Rotate adjusting position, then

secure.

(b) Repair short or replace limit

switch.

11. Gear noise. (a) Gear may need light weight

grease.

(a) Apply light weight grease.

Printed in U.S.A. 76359 Rev. 2/04

Altri manuali per TENSIONED EXECUTIVE ELECTROL

Indice

Altri manuali Da-Lite Schermo di proiezione

Da-Lite

Da-Lite Viewshare tensioned Advantage Electrol Manuale utente

Da-Lite

Da-Lite CINEMA CONTOUR SCREEN Manuale utente

Da-Lite

Da-Lite C with CSR Manuale utente

Da-Lite

Da-Lite ELECTROL Manuale utente

Da-Lite

Da-Lite Perm Wall Frame Manuale utente

Da-Lite

Da-Lite Cosmopolitan Electrol Manuale utente

Da-Lite

Da-Lite Theater-Lite Manuale utente

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Manuale utente

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL Manuale utente

Da-Lite

Da-Lite Multi vision imager Manuale utente

Da-Lite

Da-Lite TENSIONED ADVANTAGE ELECTROL Manuale utente

Da-Lite

Da-Lite Horizon Electrol Manuale utente

Da-Lite

Da-Lite Contour Electrol Manuale utente

Da-Lite

Da-Lite Multi vision imager Manuale utente

Da-Lite

Da-Lite ExecutiveElectrol Manuale utente

Da-Lite

Da-Lite PRO IMAGER Manuale utente

Da-Lite

Da-Lite Advantage Manuale utente

Da-Lite

Da-Lite Floor Model C Manuale utente

Da-Lite

Da-Lite EXECUTIVE ELECTROL Manuale utente

Da-Lite

Da-Lite Parallax Manuale utente

Da-Lite

Da-Lite Tensioned Conference Electrol Manuale utente

Da-Lite

Da-Lite IDEA Screen Manuale utente

Da-Lite

Da-Lite MULTI-MASK IMAGER Manuale utente

Da-Lite

Da-Lite Large Cosmopolitan Electrol Manuale utente

Manuali Schermo di proiezione popolari di altre marche

FART PRODUKT

FART PRODUKT Standard SCREEN Manuale utente

Draper

Draper E Series Manuale

Elite Screens

Elite Screens Elite Tripod Series Manuale utente

Laarhoven

Laarhoven Companion II Manuale utente

Renogy

Renogy RMS-LFPS-US Manuale utente

Samsung

Samsung S*H65* Manuale utente

FONESTAR

FONESTAR PPTR-43100-FA Manuale utente

Slide Clear

Slide Clear Varro XL Manuale utente

Elite Screens

Elite Screens M85XWS1-SRM Manuale utente

OS РХ-090Н Manuale utente

Niko

Niko 10-845 Manuale utente

Speaka Professional

Speaka Professional 2357532 Manuale operativo

Sima

Sima XL-72 Manuale utente

Jasic

Jasic EVO 2.0 ET-200P Manuale utente

Elite Screens

Elite Screens Starling 2 Series Manuale utente

InFocus

InFocus SC-WALL GRY-92H Manuale

Barco

Barco OverView MVL-615 Manuale utente

Draper

Draper Envoy Manuale