Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Manuale utente

Instruction Book for

TENSIONED LARGE COSMOPOLITAN®

ELECTROL®

The Da-Lite Difference.

DA-LITE SCREEN COMPANY LLC

3100 North Detroit Street

Post Office Box 137

Warsaw, IN 46581-0137 USA

P 800-622-3737 / 574-267-8101

F 877-325-4832 / 574-267-7804

www.da-lite.com

e-mail: [email protected]

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions should

always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of fire, electric shock, or injury to

persons.

SAVE THESE INSTRUCTIONS

Carefully unpack screen and remove outer wrapping from case.

The slat retainer screws must be removed before installation. Use supplied 1/8" nex key to remove silver shipping

brackets attached to slat and screen case. Orient the case with the slat down and then remove the screws. The case

must remain in that orientation throughout the installation process to avoid fabric damage.

The Tensioned Large Cosmopolitan®Electrol®comes with brackets to allow for wall mount or ceiling mount installations.

Procedures for each method are as follows:

INSTALLATION

CASE HOOK

VIEWING SURFACE

(AUDIENCE SIDE)

FIGURE 2

FIGURE 1

VIEWING SURFACE

(AUDIENCE SIDE)

CASE HOOK

WALL

MOUNT

BRACKET

STOP SCREW

CEILING

MOUNT

BRACKET

5/16x3/4"

BOLT, NUT

AND LOCK

WASHER

WALL MOUNT

BRACKET

STOP SCREW

1-1/8"

Wall Mount

1. The wall mount bracket should be fastened to wall

studs or some reinforcement within the wall. Concrete

or brick walls require special fasteners and anchors.

2. The wall bracket has holes spaced at 16" and 24" to

align with most wall studs.

3. The bracket must be level and plumb.

4. Keep in mind you will need at least 2-3/4" between the

ceiling and the top of the wall mount bracket to be

able to position the case on the bracket.

5. Mount the screen case on the wall bracket as shown

in figure 1. Be sure the case is fully seated on the

bracket. Tighten the stop screws against the wall

bracket.

Ceiling Mount

1. Be sure the ceiling has adequate reinforcement to

attach the screen brackets.

2. Attach the ceiling brackets to the wall mount bracket

using the supplied 5/16" x 3/4" bolts, washers and

nuts.

3. Position the ceiling bracket assembly on the ceiling

and attach with 5/16" bolts (not supplied). The bolts

should be long enough to pass through the drywall or

ceiling tile and penetrate at least 1-1/2" into the

reinforcement in the ceiling.

4. Mount the screen on the wall bracket as shown in

figure 2. Be sure the case is fully seated on the

bracket. Tighten the stop screws against the wall

bracket.

Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory.

No further adjustment is necessary.

SCREEN AdjUSTMENT

CONTACT DA-LITE AT 800-622-3737 OR 574-267-8101 IF SCREEN MOTOR NEEDS ADjUSTMENT.

TENSIONEd LARGE COSMOPOLITAN®ELECTROL®INSTALLATION FOR SCREENS WITHOUT A BUILT-IN LOW

VOLTAGE CONTROL

Internal wiring has been completed at the factory. Installer must route power to the wall switch and to the junction box

located on the left end of the screen case.

See wiring diagram below for wire connections.

NOTE: This screen can only be controlled by a single 120VAC or 240VAC wall switch. To use multiple switches, an optional low

voltage control must be used.

240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH:

Da-Lite offers two styles of 240 volt wall switches for standard operation.

Please see wiring diagram in wall switch boxes included with screen.

OFF

DOWN

THIS SWITCH CAN NOT

BE USED WITH LVC.

120V WIRING DIAGRAM FOR

STANDARD WALL SWITCH

SPDT SWITCH WITH

CENTER OFF

AC (COMMON)

AC HOT 120VAC 60HZ 1 AMP

BLACK/YELLOW

BLACK

RED

WHITE

RED (UP)

BLACK (DOWN)

JUNCTION BOX

LOCATED IN

LEFT ENDCAP WHITE

RED

BLACK

GREEN

MOTOR

NOTE: A SINGLE SWITCH CANNOT BE

USED TO OPERATE MORE THAN

ONE SCREEN. CONTACT THE

FACTORY FOR FURTHER

INFORMATION.

TENSIONEd LARGE COSMOPOLITAN®ELECTROL®INSTALLATION FOR SCREENS WITH A BUILT-IN LOW

VOLTAGE CONTROL

LOW-VOLTAGE WALL SWITCH

OPTIONAL IR AND RF

REMOTE CONTROL

MOTOR

BLUE (COMMON)

BROWN (HOT)

GREEN

GROUND TO CASE

240VAC 50HZ

240V WIRING DIAGRAM

WITH OPTIONAL BUILT-IN

LOW VOLTAGE CONTROL

Rj9

STOP

DOWN

GROUND–MUST BE

CONNECTED TO

BUILDING GROUND

Rj9

GREEN

FRONT BACK

UP DN GND +5V

3-POSITION

SWITCH Rj9

ILT Rj9 PIN-OUTS

(TAB IS FACING UP)

IR or UP BLACK

GND COMMON RED

+5V GREEN

DN or DATA WHITE

DRY CONTACTS

SPLITTER

+5V

COM

IMPORTANT NOTE: The wall switch is REQUIRED to make any limit

switch adjustments, EVEN if a third party control

system is used. Therefore, it is advised to wire

the switch or provide a 4-conductor connection

that is accessible.

120V WIRING DIAGRAM

WITH OPTIONAL BUILT-IN

LOW VOLTAGE CONTROL

GROUND–MUST BE

CONNECTED TO

BUILDING GROUND

Rj-14 PIN-OUTS

(TAB IS FACING UP)

IMPORTANT NOTE:

The wall switch is REQUIRED to make any limit switch

adjustments, EVEN if a third party control system is

used. Therefore, it is advised to wire the switch or

provide a 3-conductor connection that is accessible.

STOP

DOWN

POWER INPUT 120VAC / 60HZ

GREEN (GROUND)

BLACK (HOT)

WHITE (COMMON)

POWER WIRE

DATA

CABLE

Rj-45 jACK

Rj-45

RECEPTACLE

Rj-22

OUTPUT

Rj-22

jACK

Rj-22

INPUTS

Rj-22

jACK

LED

UP LIMIT

TACTILE

BUTTON

DOWN LIMIT

TACTILE

BUTTON

FRONT OF

WALL SWITCH

BACK OF

WALL SWITCH

Rj-22 PIN-OUTS

(TAB IS FACING UP)

Rj-45 PIN-OUTS

(TAB IS FACING UP)

Standard Rj-22 can be used in place of Rj-14Supplied Rj-14 cable

BLUE

YELLOW

GREEN

RED

BLACK

WHITE

+12V

BUS (RP DATA)

RQ DATA

+5V

GND

RQ CLOCK

BUS (RP DATA)

RQ DATA

+5V

GND

WHITE

GREEN

RED

BLACK

BLUE

YELLOW

GREEN

RED

BLACK

ORANGE

BROWN

PURPLE

+12V

BUS (RP DATA)

RQ DATA

+5V

GND

RQ CLOCK

MANUAL 1

MANUAL 2

DRY CONTACTS

DOWN

COMMON

BUS

5V BUS

BUS

COM

BUS

3-conductor 20-24 gauge wire can be used in place of

the supplied RJ-14 cable to connect the wall switch.

Connect the BUS terminals on the wall switch to the

corresponding BUS terminals on the splitter board.

TROUBLESHOOTING

SYMPTOM

1. Screen will not operate.

Motor does not hum.

2. Incorrect stopping position in

downward direction.

3. Incorrect stopping position in

upward direction.

4. Noise.

NOTE: Screen will operate with a

low pitched hum.

5. Coasting.

CAUSE

(a) Blown fuse.

(b) Tripped circuit breaker.

or junction.

Power at junction box

(d) Thermal overload tripped.

(e) Broken wire in the “down” or “up”

position.

(f) Defective motor, limit switch or

capacitor.

(g) Capacitor burned out.

(a) Lost roller wrap.

(b) “Down” limit switch out of

adjustment

(a) Lost roller wrap.

(b) “Up” limit switch out of

adjustment

(a) Gear Noise.

(a) Defective brake.

SOLUTION

(a) Replace fuse.

(b) Reset circuit breaker.

wire connections. Correct any

improper connections.

“Down” Position

Check for power across black

and white leads.

“Up” Position

Check for power across red

and white leads.

(d) Let motor cool down for 15

minutes. Try again.

(e) Check for continuity. Cut off old

splice and reconnect.

(f) Replace motor assembly.

NOTE: Motor is a sealed assembly.

(g) Replace motor assembly.

(a) See instructions below.

(b) Contact Da-Lite at 800-622-3737

or 574-267-8101

(a) See instructions below.

(b) Contact Da-Lite at 800-622-3737

or 574-267-8101

(a) Replace motor assembly.

Visit www.da-lite.com/products/product_videos.php to find installation and troubleshooting videos and

tutorials. You will also find a link to Live Chat for interactive support and you can contact us by email at

[email protected] or by phone at (800) 622-3737 or (574) 267-8101 with any troubleshooting questions.

THIS PAGE IS INTENTIONALLY LEFT BLANK

LIMITED ONE YEAR WARRANTY

ON DA-LITE PRESENTATION PRODUCTS

Da-Lite Screen Company LLC warrants its products to the original purchaser only, to be free from

defects in materials and workmanship for a period of one (1) year from the date of purchase by

the original purchaser provided they are properly operated according to Da-Lite’s instructions and

are not damaged due to improper handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse or accidental

damage, or which has been tampered with or repaired by a person other than authorized Da-Lite

personnel.

Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option)

the defective part of the merchandise. Returns for service should be made to your Da-Lite

dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation

expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for

damage in shipment. To protect yourself against damage or loss in transit, insure the product and

prepay all transportation expenses.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANT ABILITY. Any

implied warranties of fitness for use, or merchantability, that may be mandated by statute or

rule of law are limited to the one (1) year warranty period. This warranty gives you specific

legal rights, and you may also have other rights, which vary from state-to-state. NO LIABILITY

IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN

OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL

DAMAGES OF ANY NATURE.

In the event that there is a defect in materials or workmanship of a Da-Lite product, you may

contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, (574) 267-8101, (800) 622-

3737.

IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE SHALL NOT BE

BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH

DA-LITE’S WRITTEN INSTRUCTIONS.

Keep your sales receipt to prove the date of purchase and your original ownership.

Printed in U.S.A. 98770 Rev. 3/13

Altri manuali per TENSIONED LARGE COSMOPOLITAN ELECTROL

Indice

Altri manuali Da-Lite Schermo di proiezione

Da-Lite

Da-Lite TENSIONED CONTOUR ELECTROL Manuale utente

Da-Lite

Da-Lite PRO IMAGER Manuale utente

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL Manuale utente

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Manuale utente

Da-Lite

Da-Lite Ascender Electrol Manuale utente

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL Manuale utente

Da-Lite

Da-Lite Slimline Electrol Manuale utente

Da-Lite

Da-Lite MULTI-MASK IMAGER Manuale utente

Da-Lite

Da-Lite IDEA Screen Manuale utente

Da-Lite

Da-Lite Model C Manuale utente

Da-Lite

Da-Lite Fast-Fold truss Frame Manuale utente

Da-Lite

Da-Lite C Manuale utente

Da-Lite

Da-Lite ViewShare Advantage Electrol Retrofit Manuale utente

Da-Lite

Da-Lite ADVANTAGE ELECTROL Manuale utente

Da-Lite

Da-Lite Senior Electrol Manuale utente

Da-Lite

Da-Lite C with CSR Manuale utente

Da-Lite

Da-Lite Large Cosmopolitan Electrol Manuale utente

Da-Lite

Da-Lite PROFESSIONAL ELECTROL Manuale utente

Da-Lite

Da-Lite Perm Wall Frame Manuale utente

Da-Lite

Da-Lite DescenderPro Manuale utente

Da-Lite

Da-Lite ADVANTAGE DELUXE ELECTROL Manuale utente

Da-Lite

Da-Lite Da-Snap Wrap Around Screen Manuale utente

Da-Lite

Da-Lite senIor electrol Manuale utente

Da-Lite

Da-Lite Cosmopolitan Electrol Manuale utente

Manuali Schermo di proiezione popolari di altre marche

FART PRODUKT

FART PRODUKT Standard SCREEN Manuale utente

Draper

Draper E Series Manuale

Elite Screens

Elite Screens Elite Tripod Series Manuale utente

Laarhoven

Laarhoven Companion II Manuale utente

Renogy

Renogy RMS-LFPS-US Manuale utente

Samsung

Samsung S*H65* Manuale utente

FONESTAR

FONESTAR PPTR-43100-FA Manuale utente

Slide Clear

Slide Clear Varro XL Manuale utente

Elite Screens

Elite Screens M85XWS1-SRM Manuale utente

OS РХ-090Н Manuale utente

Niko

Niko 10-845 Manuale utente

Speaka Professional

Speaka Professional 2357532 Manuale operativo

Sima

Sima XL-72 Manuale utente

Jasic

Jasic EVO 2.0 ET-200P Manuale utente

Elite Screens

Elite Screens Starling 2 Series Manuale utente

InFocus

InFocus SC-WALL GRY-92H Manuale

Barco

Barco OverView MVL-615 Manuale utente

Draper

Draper Envoy Manuale