Dahua Technology COP Security ITC237-PU1A-IRHL Manuale utente
ITC237-PU1A-IRHL
Quick Install Guide
Official UK distribution partner
tel: +44 (0)1457 874 999 | fax: +44 (0)1457 829 201 | email: [email protected] | web: www.cop-eu.com
FEBRUARY 2017
Product specification is subject to change without notice. E&OE.
INSTALLATION OVERVIEW
When installing the ITC237-PU1A-IRHL it is important to consider both the mounting height and angle of the camera. If the camera
is mounted too high or the horizontal/vertical angle too great, then the accuracy of the recognition software will be diminished.
Listed below are the recommended mounting height and angles for reference.
Setting Height & Distance
Setting Angles
The horizontal angle should not exceed
30 degrees.
The angle of the number plate should not
exceed 5 degrees (clock or anti clockwise).
Capture Distance Mounting Height
6-10 metres 2 metres
10-14 metres 3 metres
14-18 metres 4 metres
18-24 metres 5 metres
24-40 metres 6 metres
Max Angles
Metres
Metres
5
2
4
6
10 15 20 25 30
30° Tilt
30° Tilt
30° Tilt
(Max)
(Max)
(Max)
30°
30°
35 40
ANPR Setup
Plate Angles
AB66 CDE
AB66 CDE
AB66 CDE
5°
3
Tel: +44 (0)1457 874 999 | Fax: +44 (0)1457 829 201 | Email: [email protected] | Online: www.cop-eu.com
Installation Scenarios
Network
Camera connected to network, accessed for viewing on PC using camera IP address.
Features available (with SD card installed)
• Display plate snapshot
• Building of white list
• Live View
• Alarm output
The camera can capture and store number plate snapshot images on an SD card.
No video footage will be recorded using this setup.
Camera connected to NVR, accessed for viewing on NVR OR PC using camera IP address.
Features available when connected to standard recorders;
• Display plate snapshot (camera web browser)
• Building of white list (camera web browser)
• Alarm output(camera web browser)
• Live View (camera web browser)
• Continuous video recording (NVR feature)
NVR features available when connected to NVR608/NVR616 recorders;
Any plate/whitelist/blacklist trigger events which include;
• Recording • NVR relay output
• NVR buzzer • Email
• Full screen display • Snapshot
• PTZ activation
Example 1 - Standalone ANPR camera
Example 2 - Networked ANPR camera
Barrier controlled by
Network
relay out
PC/Web Browser
PC/Web Browser
PC for
programming/monitoring
Switch
ANPR Camera
NVR
Product specification is subject to change without notice. E&OE.
12v Used when not utilizing the PoE capability, connect the 12v positive to this terminal
GND This is the terminal used for the negative connection when using 12v power
LAN Connection to Network switch or NVR PoE port
POE PoE connection to body camera
INSTALLATION
When configuring the ANPR camera for use with an NVR or as a standalone system, all devices should first be connected together.
The ITC237-PU1A-IRHL supports POE (802.3at) or can be powered by 12v DC
Housing Connections
Camera Connections
Reset Push button used to restore camera to factory settings
G Ground connection for alarm inputs
L1/L2 Alarm Inputs 1 & 2, used to trigger snapshot independently
NO Normally Open alarm output connection, used to trigger external devices such as barriers
C Common terminal to be used with NO terminal
LED_DRI
G
RESET
ARX I1 NOTX NAB I2 C
12V GND HEATER LAN POE
5
Tel: +44 (0)1457 874 999 | Fax: +44 (0)1457 829 201 | Email: [email protected] | Online: www.cop-eu.com
Once logged into the camera the live display will be shown.
To configure the camera lens and recognition settings, first select the install button.
CONFIGURATION
Once the camera has been mounted and all connections terminated, use a PC or Laptop connected to the same network switch
as the ANPR to login to the web browser interface. By default the IP address of the camera is 192.168.1.108, if required this can be
changed via the Config Tool or within the camera web browser.
Login to the camera via the computers web browser. Username: admin Password: admin123
NOTE: When connecting to an NVR it is vital to use the correct login credentials in the NVR remote device menu. Failure to input the
correct credentials will lock the camera until the correct credentials are used and the camera is rebooted.
Live View Full Screen
Snapshot
Logged Plate
Number
Plate
Snapshot
Event List
Install
The camera has built in electric back focus, this allows for adjustments to the focus to be made via the web browser (manual focus
is still required initially). To use this feature select the AutoFocus button.
Select the Region button and then Redraw, use the left mouse button to draw the detection area that vehicles will pass through.
Product specification is subject to change without notice. E&OE.
Select the Detect Line button and then Redraw, use the left mouse button to draw the detect line. The detect line is used to set
the trigger point for recognition.
Set Local Plate to the desired group, EU is the recommended setting.
Select Save to store the settings.
The Confidence Filter sets the sensitivity for detection. If this is set to high events may be missed, if set too low then false events may
occur. The recommended setting is 70.
Once the Confidence Filter has been set, click Save to store the setting.
Go to Setup > ITC > Intelligent
Select the SnapCutoutEnable box and click Save to store the setting.
Go to Setup > ITC > Snap Cutout
CONFIGURATION
7
Tel: +44 (0)1457 874 999 | Fax: +44 (0)1457 829 201 | Email: [email protected] | Online: www.cop-eu.com
Select the Format button to format the SD Card, once complete the SD Card is ready for use.
Go to Setup > Storage > Destination
When vehicles pass through the detect zone, the snapshot and number plate information should be displayed. The snapshot can
be quickly downloaded by double clicking the event entry in the event list.
The Receive Pictures tickbox is only used when monitoring events via the web interface. When used with an NVR608/616 or as an
unmonitored standalone system, the tickbox is not required to be selected.
Return to the Live tab and select the Receive Pictures tickbox.
Product specification is subject to change without notice. E&OE.
WHITELIST SETUP
To configure a whitelist to trigger the camera alarm output when a pre-configured number plate is detected follow the steps
below.
Go to Setup > ITC > BW List
Select the Enable tickbox
Select the Start Match tickbox
Select the White List Search tab
Click add to input a number plate into the whitelist database
Plate Number Vehicle number plate information. This must be entered in capital letters
Start Time The date this number plate should first be enabled in the whitelist
End Time The date this number plate should be disabled in the whitelist.
Master of Car Vehicle owners name
Gate mode Select whether the vehicle should be allowed access
Click OK to add the vehicle information to the whitelist.
9
Tel: +44 (0)1457 874 999 | Fax: +44 (0)1457 829 201 | Email: [email protected] | Online: www.cop-eu.com
Select the Link Sign Out tab, this option sets when the alarm output will trigger and also the time the alarm output triggers for.
Select the Enable tickbox to enable the alarm output
There are three operating modes:
Traffic Trust List Trigger the alarm output based on white list
All Snap Car Trigger the alarm output for all vehicles
Order Trigger the alarm output using computer software (This feature is currently unavailable)
When testing the alarm output the Hand On button can be used. Selecting this button will trigger the alarm output so control of external
devices can be tested.
IR LED ADJUSTMENT
The built-in IR LEDs of the camera can be configured to adjust the intensity of the IR Light.
Go to Setup > ITC > Extra Device > Light(485) Config
Work Mode Used to set the IR working mode manually or automatic, the recommended setting is Auto
Light Brightness The intensity of the IR lights
Light Arr Mask Select which array of LEDs are used. There are six LEDs grouped in pairs, each tickbox represents
and array. The default setting is all arrays selected.
Auto Mode Set whether the IRs should turn on/off based on LUX level or by a timed schedule.
Prevalue The level the LEDs should turn on/off at based on LUX. (Only applicable when Auto Mode is set
to Brightness).
Select Save to store the settings.
Indice
Altri manuali Dahua Technology Macchina fotografica digitale
Dahua Technology
Dahua Technology DHI-ITC952-RF2D Manuale utente
Dahua Technology
Dahua Technology DH-HAC-ME1500C Manuale utente
Dahua Technology
Dahua Technology ITC1652 Istruzioni per l’uso
Dahua Technology
Dahua Technology DH-IPC-HDEW8441R-Z Manuale utente
Dahua Technology
Dahua Technology 22204UENI-W Manuale utente
Dahua Technology
Dahua Technology D-ITC237-PW6M-IRLZF1050-B Manuale utente
Dahua Technology
Dahua Technology DHI-ITC413-PW4D-IZ3 Manuale utente
Dahua Technology
Dahua Technology NKB1000 Manuale utente
Dahua Technology
Dahua Technology K Series Manuale utente
Dahua Technology
Dahua Technology DHI-ITC237-PW6M-LZF1050 Manuale utente
