Daikin R25JV1V Manuale utente
REMOVAL
PROCEDURE
SERVICE MANUAL
2.5/3.5 kW Class
Outdoor Unit
Non-Inverter
Pair Type
Si011190
Service Manual
Removal Procedure
Outdoor Unit
Applicable Models
zCooling Only
R25JV1V
RE35LV16
RE35LV169
RE35MV16
Si011190
Removal Procedure 1
Table of Contents
1. Removal of Outer Panels ........................................................................2
2. Removal of Outdoor Fan / Fan Motor .....................................................4
3. Removal of Electrical Components (Pattern 1) .......................................7
4. Removal of Electrical Components (Pattern 2) .....................................12
5. Removal of Sound Blankets..................................................................18
6. Removal of Capillary Tube (Pattern 1)..................................................19
7. Removal of Capillary Tube (Pattern 2)..................................................20
8. Removal of Compressor ASSY.............................................................21
Note: The illustrations may be slightly different depending on the model.
Removal of Outer Panels Si011190
2Removal Procedure
1. Removal of Outer Panels
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1Appearance features
Take care not to cut your
finger by the fins of the
outdoor heat exchanger.
2Remove the screw of
the stop valve cover.
Pull down and remove
the stop valve cover.
The stop valve cover is
united with the shield plate.
When reassembling, make
sure to fit the 3 hooks.
(R10742)
(R10743)
(R16329)
Stop valve
cover
(R16330)
Shield plate
Hook
Si011190 Removal of Outer Panels
Removal Procedure 3
3Remove the 3 screws
(left: 2 screws, right: 1
screw) and lift the top
panel from the rear side
at first.
4Remove the 6 screws
of the front panel.
5Lift up the left side and
unfasten the hooks.
6Release the right side
hooks and remove the
front panel.
7The discharge grille has
2 projections to prevent
its rotation. Press the
projection from the rear
side and rotate the
discharge grille to
remove it.
Step Procedure Points
Top panel
Front panel (R16331)
(R10450)
(R16322)
Projection (rear side) (R16323)
Discharge grille
Removal of Outdoor Fan / Fan Motor Si011190
4Removal Procedure
2. Removal of Outdoor Fan / Fan Motor
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1Remove the nut of the
outdoor fan.
Nut size: M6
Align the mark of the
outdoor fan with the D-cut
section of the motor shaft
when reassembling.
2Remove the outdoor
fan.
3Cut the clamp.
(R15202)
Outdoor fan
10 mm
(R17447)
(R16324)
D-cut
Shaft
(R16313)
Clamp
Si011190 Removal of Outdoor Fan / Fan Motor
Removal Procedure 5
4Pull out the terminal
(black) from K1M (5).
The design of electrical
components is slightly
different by models.
5Pull out the 2 terminals
(red, white) from the fan
capacitor (C2R).
6Release the fan motor
lead wire from the
groove.
7Remove the screw to
detach the fan motor
fixing frame.
Put the lead wire through the
back of the motor when
reassembling so as not to be
entangled with the outdoor
fan.
Step Procedure Points
(R16180)
K1M
2
4
6
14
A2
1
3
5
13
A1
to fan motor:
black
to fan
motor
: black
(R17617)
K1M
12
34
56
1314
A1A2
C2R
to fan motor
: white
(R17618)
to fan motor
: red
to K1M (13): red
(R16179)
C2R
to K1M (13):
red
to fan motor:
red
to fan motor:
white
(R16314)
Fan motor lead wire
(R16525)
Fan motor fixing frame
(R3249)
Lead wire Outdoor fan
Removal of Outdoor Fan / Fan Motor Si011190
6Removal Procedure
8Remove the fan motor
fixing frame.
When reassembling, fit the
lower hooks into the bottom
frame.
9Remove the 3 screws
and remove the fan
motor.
Screw size: M4 × 16
10 Release the harness
from the hooks.
11 Remove the fan motor.
Step Procedure Points
(R16526)
(R10460)
(R10461)
Fan motor
(R15207)
(R15208)
Si011190 Removal of Electrical Components (Pattern 1)
Removal Procedure 7
3. Removal of Electrical Components (Pattern 1)
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1Remove the 7 screws
on the terminal board
and disconnect the
connecting wire and the
power supply wire.
2Remove the screw and
remove the wire clamp.
3Remove the screw on
the rear side.
4Lift up the guard net
and remove it.
Terminal board
(R16325)
Wire clamp
Connecting wire
Power supply wire
(R15219)
Guard net
(R15221)
Removal of Electrical Components (Pattern 1) Si011190
8Removal Procedure
5Remove the 4 screws
on the right side.
6Unfasten the hook of
the right side panel.
When reassembling, make
sure to fit the hook.
7Remove the right side
panel.
Step Procedure Points
(R15222)
(R10467)
Right side panel
(R16317)
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Daikin Unità di trattamento dell'aria
Daikin
Daikin DSC Series Manuale utente
Daikin
Daikin AWST18SU14 AA Series Manuale utente
Daikin
Daikin EEV Series Manuale utente
Daikin
Daikin OAH 003G Manuale
Daikin
Daikin PreciseLine Series Manuale
Daikin
Daikin Vision CAH 003-090 C Manuale
Daikin
Daikin VISTA FXZQ TBVJU Guida alle dimensioni
Daikin
Daikin DAX Commercial Manuale utente
Daikin
Daikin Easdale 25 Manuale
Daikin
Daikin Clima-Flex CLIFC FIXED Series Manuale utente
Daikin
Daikin ARUF Series Manuale utente
Daikin
Daikin Altherma 3 R F Come usare
Daikin
Daikin Destiny VFD Series Manuale
Daikin
Daikin EDMFA04A6 Manuale utente
Daikin
Daikin SkyAir FTQ18TAVJUA Manuale utente
Daikin
Daikin ATM18MV2S Manuale utente
Daikin
Daikin D-AHU Professional AH-ERQ-U Manuale utente
Daikin
Daikin FWE04FF/T Manuale utente
Daikin
Daikin Altherma 3 H HT ECH2O Series Manuale utente
Daikin
Daikin FWE03D Series Manuale utente
