Daikin TSTATD1152-2 Manuale utente
Owner's
Manual
TSTATD1152-2
RESIDENTIAL
for
Residential Use
Digital Thermostat
5+2 Day Programmable
2
Table of Contents
Safety Warnings ...................................................................3
Location of Controls.............................................................4
Dispay.....................................................................................5
Normal Operation
Manual Operation ..................................................................6
Programmed Operation...........................................................7
Clock Set................................................................................8
Time Period Programming
Overview ................................................................................................. 9
Weekday Programming........................................................................ 10
Weekend Programming........................................................................ 13
Advanced Setup...................................................................17
Advanced Features..............................................................18
Factory Defaults...................................................................19
Calibration ............................................................................20
Battery Replacement ..........................................................21
Warranty................................................................................22
The two Alkaline “AA” batteries must be replaced at
least once every 12 months to ensure proper operation.
The Low Battery icon (fig. 1) will appear on the display
when it is time to replace the batteries. If the thermostat
is connected to 24v power, the batteries should still be
installed, but are not required.
When is displayed the batteries must be replaced
immediately. The manufacturer cannot be liable for
improper operation of the thermostat if the batteries are not
immediately replaced.
Annual battery replacement is especially critical in locations
subject to freezing temperatures. The thermostat will be
unable to turn on the heating system if the batteries are
exhausted.
This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1)This device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
Follow Installation Instructions carefully.
DISCONNECT POWERTOTHE
HEATER - AIR CONDITIONER
BEFORE REMOVINGTHE OLD
THERMOSTAT AND INSTALLING
THE NEWTHERMOSTAT.
3
fig. 1
Safety Warnings
4
Location of Controls
NEXT BUTTON
RESET FILTER
How to Use: Press and
hold the RESET FILTER
button to clear the
icon from the
display (pg 5). To adjust
when the icon
appears, see Advanced
Setup screens (pg 18).
FILTER
FILTER
COOLER
&
WA
RMER
BUT
TONS
PROGRAM SWITCH
RUN program
Program OFF
SET program
SET
HEAT
BATTERIES
COOL
OFF
PROGRAM
RUN OFF SET
RESET
FILTER
FAN
NEXT
HEAT
AUTO
ON On or Auto
FAN SWITCH
For programming
How to use:The NEXT
button is used to advance
from one step to the next
in the programming and
advanced setup screens
(pgs 10 - 18).
BI-COLOR LED
Heat or Cool demand
indicator when system
powered: Red = Heat
Green = Cool
MODE
SWITCH
Cool, Off,
or Heat
Su
PM
5
Display
SET
MTuWThF
SaSu
AM
PM MorningEvening
Day
Night
HEAT
COOL
FILTER
88
88
12:00
1Day of the week. When programming, MTuWThF represent the
five weekdays and SaSu represent the two weekend days.
2Heat and Cool indicators. In normal operation, Heat or Cool
appears, depending on the Mode Switch position. When heat
or cool is energized, the Heat or Cool indicator will flash.
3Clock Display.
4Time period indicators.These indicate the part of the
program that is currently active, if the Program Switch
is positioned to RUN.
5Desired set temperature.
6Current room temperature.
7Indicates when the filter should be serviced. Appears
after 0 - 1950 hours of blower operation (adjustable).
8Indicates batteries need replacement.
6
Normal Operation
1Select Cool or Heat with the Mode Switch.
2Normally leave the fan switched to Auto.
In Fan Auto, the fan will turn on only with a heat
or cool demand. When Fan On is selected, the fan will run
continuously.
3Adjust the desired set temperature with the
COOLER and WARMER buttons.
COOLER &
WARMER
BUTTONS
PROGRAM SWITCH
RUN program
Program OFF
SET program
SET
HEAT
BATTERIES
COOL
OFF
PROGRAM
RUN OFF SET
RESET
FILTER
FAN
NEXT
HEAT
AUTO
ON
On or Auto
FAN
SWITCH
MODE SWITCH
Cool, Off, or Heat
Su
PM
Manual Operation (Program Switch OFF)
7
Normal Operation
1Select Cool or Heat with the Mode Switch.
2Select RUN with the Program Switch.
3Normally leave the fan switched to Auto. In Fan Auto, the fan
will turn on only with a heat or cool demand. When Fan On is
selected, the fan will run continuously.
4The desired set temperature may be temporarily overridden.
The thermostat will revert to the programmed settings in the
following time period.
COOLER &
WARMER
BUTTONS
PROGRAM SWITCH
RUN program
Program OFF
SET program
SET
HEAT
BATTERIES
COOL
OFF
PROGRAM
RUN OFF SET
RESET
FILTER
FAN
NEXT
HEAT
AUTO
ON
On or Auto
FAN
SWITCH
MODE SWITCH
Cool, Off, or Heat
Su
PM
Programmed Operation
PROGRAM
RUN OFF SET
PM
Su
8
Clock Set
Slide the Program Switch
to the SET position.
Setting the time & day are the first two steps after sliding the Program
Switch to SET.
This thermostat is preprogrammed from the factory to operate
1 or 2-Stage equipment without the need for further programming.
To optimize the installation of this thermostat follow the instructions
in the Advanced Setup section.
To slew the time more rapidly, push and hold the
COOLER or WARMER buttons.
Use these buttons to
adjust the current time.
Use these buttons to
adjust the current day.
NEXT
Press NEXT
to advance
9
Time Period Programming
Overview
• Slide the Program Switch to the SET position.
• The blinking icon(s) on the display may be
changed by pressing the COOLER or WARMER
buttons.
• After the blinking icon is changed to the desired
selection, press the NEXT button.
• Each item in the time period programming screens will flash and can
be modified with the COOLER & WARMER buttons.
• Continue the steps above until programming is complete.
• Slide the Program Switch to RUN and the thermostat will run the time
period program.
• If the Program Switch is in the OFF position, the thermostat will not run
the time period program. In this case, the thermostat will be a manual
heat or cool only thermostat.
PROGRAM
RUN OFF SET
PM
Su
PROGRAM SWITCH
10
Time Period Programming
PROGRAM
RUN OFF SET
AM
MTuWThF
Morning
AM
MTuWThF
Morning
SET
COOL
AM
MTuWThF
Morning
SET
HEAT
AM
MTuWThF
Day
Weekday Programming
Setting the time & day are the first two steps after
sliding the Program Switch to SET (page 8).
Use these buttons to
adjust the start time for
the morning time period.
Use these buttons to
adjust the cool setpoint for
the morning time period.
Use these buttons to
adjust the heat setpoint for
the morning time period.
Use these buttons to
adjust the start time for
the day time period.
Next Page
NEXT
Press NEXT
to advance
NEXT
Press NEXT
to advance
NEXT
Press NEXT
to advance
NEXT
Press NEXT
to advance
Indice
Altri manuali Daikin Termostato
Daikin
Daikin Airzone DZK-4 Manuale utente
Daikin
Daikin EKRTR Manuale utente
Daikin
Daikin One+ Guida
Daikin
Daikin EKRTRB Manuale utente
Daikin
Daikin TSTATD2100-2 Istruzioni operative
Daikin
Daikin MT 168 Manuale
Daikin
Daikin 910121746 Istruzioni generali
Daikin
Daikin TSTATD1100-2 Istruzioni operative
Daikin
Daikin One+ Istruzioni per il montaggio
Daikin
Daikin RoCon UFH Manuale utente
Daikin
Daikin homecontrols EKRCTRDI2BA Guida utente
Daikin
Daikin Premium Mini D2270 Istruzioni originali
Daikin
Daikin ENVi Manuale utente
Daikin
Daikin TSTATD2200C-2 Istruzioni operative
Daikin
Daikin EKWCTRDI1V3 Manuale utente
Daikin
Daikin 668811101 Istruzioni generali
Daikin
Daikin 910121748 Istruzioni generali
Daikin
Daikin Altherma 3 R F Manuale utente
Daikin
Daikin ENVi Manuale utente
Daikin
Daikin ESFV06A6 Manuale utente
