Dakota Alert AD-01 Kit Manuale utente

AD-01 Kit

Auto Dialer

Owner’s Manual

AD-01 Kit Manual.indd 1 10/15/2009 10:17:55 AM

2 3

Warnings:

This device complies with Part 15 of the FCC rules, Operation of this device is subject to the fol-

lowing conditions: 1. This device may not cause harmful interference. 2. This device must accept

any interference, including interference that may cause undesired operation.

Features:

Wireless alarm; programmable entry/exit delay time; two separate dialer alarms, alarm and panic;

select up to 9 (32 digit) user programmable phone numbers for each alarm; dierent 10 second

recordable message for each alarm; arm/disarm using keypad or remote keyfob; wireless panic;

built-in tamper switch; built-in terminal block for alarm and siren connection; DC adaptor with

battery back-up; programmable as silent alarm (dialer only) or audible (siren + dialer).

Contents:

1 - Auto Dialer

2 - RF PIR Sensor

2 - RF Keyfob

1 - 12V DC Adaptor

1 - Installation & Programming Guide

1 - Telephone Cable

1 - Back-up Battery

AD-01 Kit Manual.indd 2 10/15/2009 10:17:55 AM

2 3

IMPORTANT

Before you install the PIR Detectors, please take these points into consideration:

Don’t position the detectors facing windows.

Don’t position in direct sunlight.

Don’t position above heat sources or in areas of moisture.

Don’t let pets roam into the detection area when the system is armed.

The PIR Sensor is set to Alarm 2 so take this into account

when you are programming your voice messages.

Opening the PIR Sensor to access dipswitches and battery connector:

1. Slide the PIR Sensor o the bracket (use the bracket as a template for mounting.)

2. Using a small standard screwdriver, press the release clip on the bottom of the PIR Sensor.

3. Separate the two parts.

Opening the RF Keyfob (only necessary when it is time to change the battery):

1. Using a small Phillips screwdriver, remove the screw from the back of the keyfob.

2. Take a small standard screwdriver and place in groove seperating the two keyfob halves.

3. Slowly twist and the keyfob housing should separate.

AD-01 Kit Manual.indd 3 10/15/2009 10:17:55 AM

4 5

Installation

Tools needed: Small Phillips Screwdriver;

Large Phillips Screwdriver; Small Standard Screwdriver.

Set Up:

1. Set PIR and AD-01 dipswitches to match. The rst ve

dipswitches on both units (Figure 1 - 1 and Figure 2 - 1) need to

be set exactly the same with the last 3 dipswitches set to “o”.

(Note: On the PIR sensor, “o” is in the down position. On the Dialer,

“o” is in the up position.)

2. Install battery in PIR sensor (Figure 1 - 2) and mount at

desired location. (Note: recommended to replace batteries every

6 months.)

3. Plug the supplied phone cord into the “LINE” jack (Figure 2-5) and then into your home phone

jack. If you wish to connect a phone at the dialer location, you can connect the phone to the

“PHONE” jack (Figure 2-6) on the dialer.

4. (Note: please read all of step 4 before continuing). Remove the battery insulator by pulling the tab

on the keyfob. Plug the DC adaptor into the dialer (Figure 2 - 3) and plug into wall outlet. Wait 20

seconds. You now have 30 seconds to teach the dialer. Press the RECORD button (Figure 3 - 3) on

the dialer and the display will show “learning 0.” Press any key on the RF Keyfob. The display will

then show“learning 1” followed by a BEEP to conrm that it has learned the rst keyfob. You then

have another 30 seconds to teach it another keyfob (“learning 2”) and so on up to 5 keyfobs.

Figure 1

AD-01 Kit Manual.indd 4 10/15/2009 10:17:55 AM

4 5

5. (Note: Tamper switch (Figure 2-4) arms automatically

when depressed and will cause alarm 1 to activate

when released. Disarm by entering password code

1234 into dialer followed by the ESC button or by using

the OFF button on the keyfob). Install the back-up

battery (included) into the dialer. Use a small Phillips

screwdriver to remove screw above battery cover

(Figure 2 - 2). Remove cover by sliding downwards.

Plug in 9V battery making sure not to force onto

battery holder incorrectly. Put 9V battery in space

provided, close battery cover, and replace the screw.

6. The BE+ and BE- terminals (Figure 2-7) are a 12VDC,

150mA (maximum) voltage output which can be used

to power an external bell or whistle when the dialer is

activated.

7. Continue on to the Advanced Operations to program

your dialer or refer to the “AD-01 Quick Reference

Programming”on page 14.

Figure 3

2 3

Figure 2

1 7 5 6 4 3 2

AD-01 Kit Manual.indd 5 10/15/2009 10:17:55 AM

6 7

Advanced Operations

HOW TO PROGRAM THE AUTO DIALER

*If no key is pressed for 30 seconds, the dialer will automatically exit the programming mode.

Notice: The system must be in the OFF mode for all programming.

How to record the voice messages:

Alarm 1 = Tamper and panic alarm. Alarm 2 = PIR sensors and hard-wired input.

1. Key in the four digit user password code (factory default is 1234.)

2. Press RECORD.

3. Press 1(to save as the message for alarm 1) or 2(to save as the message for alarm 2).

4. Press ENTER to start recording your 10 second message.

5. Press ENTER to stop the recording early or wait for the 10 seconds to end.

Quick guide: Press 1 2 3 4 > RECORD > 1> ENTER, record message now

How to play back the message:

Press 1 2 3 4 > PLAY > 1> ENTER to play back the recorded message.

(Notice: 1= the rst message, 2= the second message).

How to program phone numbers:

You can enter a maximum of nine telephone numbers for the alarms. Each number can be

a maximum of 32 digits. (If you are using this Auto Dialer on an oce/work phone system

you may have to enter 9 before the number to get a line out.)

AD-01 Kit Manual.indd 6 10/15/2009 10:17:55 AM

6 7

1. Key in the four digit user password code (factory default is 1234.)

2. Press PROGRAM > 3 > ENTER.

3. The number you press next will select the position in the sequence you want that

telephone number to dial (1= rst number called, 2= second number called, and so on).

4. Press ENTER and key in the rst telephone number.

5. Press ENTER to exit the programming mode.

6. Repeat the process until you have entered all the numbers you wish the Auto Dialer to

call once it has been activated (maximum 9 dierent numbers.)

Quick guide: Press 1 2 3 4 > PROGRAM > 3 > ENTER > 1> ENTER > Telephone # > ENTER

How to delete phone numbers:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 3 > ENTER.

3. Press N(N = 1for the rst number called; 2for the second number called; etc.)

3. Press ESC to exit the programming mode.

Quick guide: Press 1 2 3 4 > PROGRAM > 3 > ENTER > N> ESC

How to designate telephone numbers to ALARM 1 and ALARM 2:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 6 > ENTER.

3. Press X (X = 1for alarm 1; 2for alarm 2). Press ENTER.

4. Press N (N = 1for rst phone number; 2for second phone number, etc.). Press ENTER.

5. Repeat the process to designate any other numbers to each alarm.

Quick guide: Press 1 2 3 4 > PROGRAM > 6 > ENTER > X> ENTER > N> ENTER

AD-01 Kit Manual.indd 7 10/15/2009 10:17:55 AM

How to change the user password code (factory default is 1234):

1. Key in the four digit user password code (factory default 1234.)

2. Press PASSWORD

3. The LCD will change to n-p.

4. Key in your new four digit user password code.

5. The LCD will change to c-p.

6. Key in your new four digit user password code again.

7. The LCD will change to acc.

Quick guide: Press 1 2 3 4 > PASSWORD > New Code > Conrm New Code

How to program the Auto Dialer to give an audible alarm as well as sending a voice

message (factory default is alarm ON):

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 1 > ENTER

3. Press N(N = 0for without audible alarm, 1for with audible alarm). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 1 > ENTER > N> ENTER

How to set the time the alarm will sound on activation (default time is 3 minutes):

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 2 > ENTER

3. Press Time (Time = 1for one minute, 2for 2 minutes, etc. up to 99 minutes). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 2 > ENTER > Time > ENTER

8 9

AD-01 Kit Manual.indd 8 10/15/2009 10:17:55 AM

8 9

How to set Entry/Exit Delay times (default both delay set at 30 seconds):

The entry/exit times are the times the Auto Dialer gives you to enter/exit the area covered

by the system before it arms/alarms. These are pre-set to 30 seconds. You can also change

the timing to instant or 60 seconds.

Entry Delay:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 4 > ENTER

3. Press N (N = 0for instant; 3for 30 seconds; 6for 60 seconds). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 4 > ENTER > N> ENTER

Exit Delay:

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 5 > ENTER

Press N (N = 0for instant; 3for 30 seconds; 6for 60 seconds; 9for 90 seconds). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 5 > ENTER > N> ENTER

How to set an Entry/Exit delay sound (factory setting Entry/Exit delay with sound):

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 7 > ENTER

3. Press N(N = 0without sound; 1with sound). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 7 > ENTER > N> ENTER

AD-01 Kit Manual.indd 9 10/15/2009 10:17:55 AM

10 11

How to disable Tamper Function (factory setting Tamper ON):

1. Key in the four digit user password code (factory default 1234.)

2. Press PROGRAM > 8 > ENTER

3. Press N(N = 0without tamper function; 1with tamper function). Press ENTER.

Quick guide: Press 1 2 3 4 > PROGRAM > 8 > ENTER > N> ENTER

HOW TO OPERATE THE AUTO DIALER

How to Arm the Alarm System/Turn the Dialer ON:

1. Check that the voice message and at least one phone number has been programmed

into the Auto Dialer.

2. Press 1 2 3 4 > ENTER or press the ‘ON’ button on the RF Keyfob. The Auto Dialer will

show ‘ON’ on the display.

3. The alarms will become active after the delay time you have set has expired.

Quick guide: Press 1 2 3 4 > ENTER or Press the ‘ON’ button on the RF Keyfob

How to disarm the Alarm System/Turn Dialer OFF:

To disarm the Alarm System or to stop the Dialer from dialing out after either the tamper

switch (if connected and active) or a alarm input has been activated, key in the four digit user

password code followed by ESC. Alternatively, press the ‘OFF’ button on the RF Keyfob. The

Auto Dialer will revert to the ‘OFF’ mode and must be re-set to the ‘ON’ mode as above.

Quick guide: Press 1 2 3 4 > ESC or Press the ‘OFF’ button on the keyfob

AD-01 Kit Manual.indd 10 10/15/2009 10:17:55 AM

Altri manuali per AD-01 Kit

Indice

Altri manuali Dakota Alert Sistema di sicurezza

Dakota Alert

Dakota Alert WPS-1000 Manuale utente

Dakota Alert

Dakota Alert DCPAS-4000 Manuale utente

Dakota Alert

Dakota Alert CAD-03 Kit GSM Manuale utente

Dakota Alert

Dakota Alert AD-01 Kit Manuale utente

Dakota Alert

Dakota Alert WTS-1000 Manuale utente

Dakota Alert

Dakota Alert CAD-05 Kit GSM Manuale utente

Dakota Alert

Dakota Alert WPS-1000 Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente