Dams TGDMARM Manuale utente

M4x12mm M5x12mm M6x12mm

902-9Kg

A B

1234

Installation guide B(8PCS) C(3PCS) D(16PCS) E(1PC) F(1PC)

4x4 5x5

A(8PCS) Allen Key Allen Key

1.Support arm (1PC)

2.Base Mounting Plate (1PC)

3.Protection pad (1PC)

4.Protection pad (1PC)

5.Perforated plate (1PC)

6.Long screw (1PC)

7.Protection pad (1PC)

8.Pressure plate (1PC)

9.Handwheel (1PC)

10.Mount Plate (2PCS)

11.Clip (2PCS)

STEP 1

The Preparation Before Monitor Installation

1.Make sure there are VESA holes 100x100mm or 75x75mm in the monitor. If not, cannot be installed.

2.Remove the original fixed base of monitor.Be careful not to scratch the screen.

75x75mm,100x100mm

STEP 2-A

Option1: Clamp

Tighten

For desk thickness:

20-30mm

DESK

Desktop

Caution

STEP 2-B Option2: Grommet

Notice: Keep the counterbore

side down

For desk thickness: 25-100mm

Tighten

Available hole size:8.5-70mm

Desktop

STEP 3

Connect the plate and monitor

monitor

Use washer if needed (D)

Use the allen key (F) to tighten the screw

Tighten

STEP 4

Install the monitor to the arm

Hang the monitor on the plate

from top to bottom and ensure

it is tightened

Connection plate

Lock

Item No.: TGDMARM

11C

Max:970

360°

100

±90°

102

±180°

±120°

±180°

±90°

-90°

15°

±120°

STEP 5 Adjust the monitor

Caution: Please do not fully

reverse the monitor screen-to

prevent damage to the fixings.

To adjust the swivel function by 5*5 allen key(F) on position 1

To adjust the tilt function by 5*5 allen key(F) on position 2

Adjust the Rotation Arm

STEP 6

When the size of monitors is small and the distance between the two monitors is too large,

the arms can be rotated to adjust the distance between the two monitors.

Cable Management

1. Take off cable management and put cable

management back to cover cables once

finishing the management

Cable

2. Buckle the clips (11) after

organising the cables.

Cable

Specification

CAUTION

This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children.

● Make Sure these instructions are read and completely understood before attempting installation. If you are unsure of any part of this installation, please contact a professional

installer for assistance.

● The desk or mounting surface must be capable of supporting the combined weight of the mount and the display,otherwise the structure must be reinforced.

● Safety gear and proper tools must be used. A minimum of two people are required for this installation. Failure to use safety gear can result in property damage, serious injury or

death.

● please check joint parts every two months, making sure the screws are nor loosened.

This product was designed to be installed on a desk. Before installing, make sure the mount will support the combined load of the equipment and

hardware. Never exceed the maximum load capacity 9 KG, or else it may result in product failure or personal injury.

Note:this product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury.

Warning:

obsolete products can be sent back to the manufacturer or handed over to professional institutions.

To maintain the gas mechanism in peak performance - it is suggested to raise the monitor arm up to the maximum height: ideally twice per month.

This product contains high pressure gas spring parts, please do not put it into fire, high temperature, or disassemble it, which will lead to

personal injury. The

Factory setting: 5-7KG

To equalise the mount and