Danfoss 088U0213 Manuale utente
SE
088U0213
Instruction CF-RF Room Thermostat with Infrared Floor Sensor
Instruktion CF-RF Raumthermostat mit Infrarot-Bodensensor
Vejledning til CF-RF-rumtermostat med infrarød gulvsensor
InstructionsThermostat d’ambiance CF-RF avec Capteur au sol infrarouge
Instruction CF-RF rumstermostate med infraröd golvsensor
1VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
GB Instruction.......................3
DInstruktion......................15
DK Vejledning......................28
FInstruction......................41
SE Bruksanvisning . . . . . . . . . . . . . . . . . 54
2VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
3VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
1.FunctionalOverview........................4
2.Installation.................................5
3. Temperature Settings . . . . . . . . . . . . . . . . . . . . . . . 6
4. Transmission Test . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.Mounting .................................11
6.Uninstallation .............................12
7.Specications..............................13
8.Troubleshooting...........................14
9. Figures and Illustrations. . . . . . . . . . . . . . . . A1-A2
GB Index
4VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
1. Functional Overview
Front - g. 1
Up/down selector
Push button
Red LED (behind the cover)
InfraRed oor sensor
LED modes
Permanent light ON
No light OFF
Slow ashing Flashes
Fast ashing Flickers
Back - g. 2
Back plate
Back plate lock/unlock (turn 90°)
Screw hole for wall mounting
Battery placement
Screw and wall plug
5VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
2. Installation
Note:
• To activate batteries in the Room Thermostat,
please remove enclosed strips from the batteries.
• The assignment of the Room Thermostats to the
Master Controller should be within 1½ m distance
Activate Install mode on
Master Controller - g. 1.
• Use the menu selection button to select the
Install mode. Install LED ashes
• Activate Install mode by pressing OK . Install
LED goes ON
Activate Install mode on
Room Thermostat
• Press the push button . LED and icker
during communication
Select output on Master Controller
• All available output LEDs on Master Controller
light up, and the rst of them ashes
• Press output selection button , to select
desired output (ashes) and accept with OK
• All output LEDs go OFF. Selected output
stays ON shortly
6VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
Room Thermostat installation status
• Satisfactory - LED goes OFF
• Not satisfactory - LED ashes 5 times
Note: A Room Thermostat can be assigned to sev-
eral outputs if needed by repeating the installation
process.
3. Temperature Settings
Digital Display - g. 1
Set value adjustment
Minimum temperature limitation
Maximum temperature limitation
Lock icon (settings locked from
Remote Controller, CF-RC)
Transmission link icon
Low battery indicator
Alarm icon
Timer icon (time program is active from
Remote Controller, CF-RC)
Room temperature
Floor surface temperature
7VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
Changing default display temperature
- g. 1.
1. The actual room temperature is shown in the
display as default
2. To change default display from actual room
temperature to actual oor surface tempera-
ture, press and hold the push button
until SET MAX is shown in the display
3. Press the button shortly and repeatedly
until or is ashing in the display
4. Press the up/down selector to select the
new default display temperature:
Room temperature
Floor surface temperature
Setting of room temperature
1. Make sure actual room temperature is shown
in the display
2. Press the up/down selector to set the
desired room temperature value. SET is shown
in the display
3. When releasing the up/down selector the
display returns to actual temperature
Note: The thermostat regulates the oor heating
system according to room temperature set point,
within the maximum and minimum limitations
dened for the oor surface temperature
8VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
Room temperature limitation
1. Make sure actual room temperature is shown
in the display
2. Press the push button until SET MAX is
shown in the display
3. Press the up/down selector to set the
maximum room temperature limitation
4. Press the push button shortly, SET MIN is
shown in the display
5. Press the up/down selector to set the mini-
mum room temperature limitation
6. Press the push button shortly and the
actual oor surface temperature is shown in
the display
Floor surface temperature limitation
1. Ensure actual oor surface temperature is
shown in the display illustrated by
2. Press and hold the push button until SET
MAX is also shown in the display
3. Press the up/down selector to set the
maximum oor surface temperature limitation
4. Press the push button shortly, SET MIN is
also shown in the display
5. Press the up/down selector to set the mini-
mum oor surface temperature limitation
9VI.UH.R1.80 Produced by Danfoss Floor Heating Hydronics 01.2006
Instruction CF-RF Room Thermostat with InfraRed Floor Sensor
IMPORTANT!
As heat emission from the oor may vary slightly
depending on oor covering - and thereby cause
inaccurate temperature measurement - it may be
necessary to adjust the setting of max. and min.
oor surface temperatures accordingly.
! It is important always to follow recommendations
from the oor manufacturer regarding max. oor
surface temperature.
! It is recommended always to include mixing shunt
for oor heating circuits in order to ensure optimal
ow temperature. - In addition to minimised energy
consumption, correct setting of the ow tempera-
ture will eliminate the risk of excessive heat transfer
to the oor.
Indice
Lingue:
Altri manuali Danfoss Accessori
Danfoss
Danfoss DST X730 Manuale utente
Danfoss
Danfoss DGS Series Manuale utente
Danfoss
Danfoss Link RS Manuale utente
Danfoss
Danfoss DGS Manuale utente
Danfoss
Danfoss Z-Wave RS Manuale utente
Danfoss
Danfoss DST X510 Manuale utente
Danfoss
Danfoss 084H4505 Manuale utente
Danfoss
Danfoss AKS 4100U Manuale utente
Danfoss
Danfoss KPP Pulse Pickup Manuale
Danfoss
Danfoss AKS 41U Manuale utente
Danfoss
Danfoss 176F6757 Manuale utente
Danfoss
Danfoss AKS 41 Manuale utente
Danfoss
Danfoss AKS 4100 Manuale utente
Danfoss
Danfoss AKS 4100 Manuale utente
Danfoss
Danfoss 176F6516 Manuale utente
Danfoss
Danfoss 080Z2819 Manuale utente
Danfoss
Danfoss DGS Series Manuale utente
Danfoss
Danfoss 086U9563 Manuale utente
Danfoss
Danfoss 176F6516 Manuale utente
Danfoss
Danfoss AKS 4100 Manuale utente
