Danfoss iC7 Series Manuale utente
1 Overview
1.1 Description
The in-bottom/out-back cooling kit fits FA09 and FA10 frequency converters mounted in Rittal TS8 cabinets. When the kit is instal-
led, air flows into the bottom duct and out through the back duct of the frequency converter. See Illustration 1.
6
3
5
1
4
2
e30be922.10
Illustration 1: Direction of Airflow with Kit Installed
1
Top cover
2
Frequency converter
3
Bottom duct assembly
4
Back channel airflow (intake)
5
Back channel airflow (exhaust)
6
Mounting plate
1.2 Kit Numbers
Use these instructions with the following kits.
Table 1: Numbers for In-bottom/Out-back Cooling Kits
Number
Kit description
176F4040
In-bottom/Out-back cooling kit for FA09 frequency converters
176F4041
In-bottom/Out-back cooling kit for FA10 frequency converters
AN371942757356en-000101 / 136R0252 | 1Danfoss A/S © 2022.03
Installation Guide
In-bottom/Out-back Cooling Kit for FA09-FA10
iC7 Series Frequency Converters
1.3 Items Supplied
The kit contains the following parts:
Table 2: Contents of In-bottom/Out-back Cooling Kit
Item
Quantity
Telescopic bottom duct assembly
1
Rubber EPDM ribbed seal
1
Cutout gasket
1
Drive slot gasket
1
Seal plate gasket
2
Seal plate
2
Duct support plate
1
Duct support plate gasket
1
Top cover
1
Top cover gasket
1
Back vent
1
Back vent gasket
2
Mounting plate gasket
2
Backplate gasket
2
Clip-on nut
12
M10x30 screw
4
M5x16 countersunk screw
7
M5x18 screw
6-8
M6x12 screw
6-8
M5x10 taptite screw
5-10
M5 hex nut
6
AN371942757356en-000101 / 136R02522 | Danfoss A/S © 2022.03
Overview
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
-
-
-
-
-
-
-
-
-
-
-
2 Installation
2.1 Safety Information
NOTICE
QUALIFIED PERSONNEL
Only qualified personnel are allowed to install the parts described in these installation instructions.
Disassembly and reassembly of the frequency converter must be done in accordance with the corresponding service guide.
Use the standard fastener torque values from the service guide, unless the torque value is specified in these instructions.
WARNING
ELECTRICAL SHOCK HAZARD
The frequency converter contains dangerous voltages when connected to mains voltage. Improper installation, and installing or
servicing with power connected, can cause death, serious injury, or equipment failure.
Only use qualified electricians for the installation.
Disconnect the frequency converter from all power sources before installation or service.
Treat the frequency converter as live whenever the mains voltage is connected.
Follow the guidelines in these instructions and local electrical safety codes.
WARNING
DISCHARGE TIME (20 MINUTES)
The frequency converter contains DC-link capacitors, which can remain charged even when the frequency converter is not pow-
ered. High voltage can be present even when the warning indicator lights are off.
Failure to wait 20 minutes after power has been removed before performing service or repair work can result in death or serious
injury.
Stop the motor.
Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and
DC-link connections to other frequency converters.
Wait 20 minutes for the capacitors to discharge fully before performing any service or repair work.
Measure the voltage level to verify full discharge.
NOTICE
ELECTROSTATIC DISCHARGE
Electrostatic discharge can damage components.
Ensure discharge before touching internal frequency converter components, for example by touching a grounded, conduc-
tive surface or by wearing a grounded armband.
AN371942757356en-000101 / 136R0252 | 3Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
-
2.2 Installation Overview
NOTICE
APPLYING GASKETS
This kit contains self-adhesive gaskets to ensure a proper seal between metal parts.
Before affixing a gasket, check that the part matches the gasket and that no holes are covered.
Lorem ipsum
e30bj238.10
1
2
3
4
5
6
7
8
9
10
11
12
Illustration 2: Overview of In-bottom/Out-back Cooling Kit
AN371942757356en-000101 / 136R02524 | Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
1.
2.
3.
1
Mounting plate
2
Top cover
3
Top cover gasket
4
Frequency converter
5
Duct support plate gasket
6
Duct support plate
7
Telescopic bottom duct
8
Upper mounting hole
9
Mounting plate gasket
10
Back vent
11
Backplate
12
Lower mounting hole
2.3 Preparing the Mounting Plate
To create mounting holes and vent holes in the mounting plate, use the following steps. Use the dimensions in Illustration 3 for
FA09 frequency converters, and Illustration 4 for FA10 frequency converters.
Procedure
Drill 4 mounting holes in the mounting plate using the dimensions in the template.
The holes must match the holes in the frequency converter.
Insert 4 M10 pem nuts (not supplied) in the mounting holes.
Cut out the vent opening in the mounting plate using the dimensions in the template.
The openings must match the upper duct opening in the frequency converter.
AN371942757356en-000101 / 136R0252 | 5Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
844 (33.2)
2x Ø 8 (0.3)
Drive Mounting Holes
e30bj223.10
200 (7.9)
130 (5.1)
214 (8.4)
180 (7.1)
7 (0.3)
78 (3.1)
122 (4.8)
10 (0.4) 110 (4.3)
68 (2.7)
7 (0.3)
78 (3.1)
122 (4.8)
6x Ø 8 (0.3)
2x Ø 8 (0.3)
Drive Mounting Holes
Illustration 3: FA09 Mounting Plate Template for In-bottom/Out-back Cooling
AN371942757356en-000101 / 136R02526 | Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
1.
2.
e30bj224.10
2x Ø 8 (0.3)
Drive Mounting Holes
321 (12.6)
280 (11.0)
74 (2.9)
8x Ø 6 (0.2)
130 (5.1)
110 (4.3)
10 (0.4)
1051 (41.4)
271 (10.7)
2x Ø 8 (0.3)
Drive Mounting Holes
Illustration 4: FA10 Mounting Plate Template for In-bottom/Out-back Cooling
2.4 Preparing the Backplate
To create a vent opening in the cabinet backplate to match the opening in the mounting plate, use the following steps. Use the
dimensions in Illustration 5 for FA09 frequency converters, and Illustration 6 for FA10 frequency converters.
Procedure
Cut out the vent opening in the cabinet backplate using the dimensions in the template.
The vent opening must match the mounting plate opening.
Drill screw holes (6 mm) around the vent opening using the dimensions in the template.
The FA09 requires 6 holes around the vent opening, and the FA10 requires 8 holes around the opening. The holes must
align with the holes in the outer flanges of the back vent.
AN371942757356en-000101 / 136R0252 | 7Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
246 (9.7)
13 (0.5)
10 (0.4)
188 (7.4)
6x Ø 7 (0.3)
167 (6.6)
e30bj234.10
Illustration 5: FA09 Cabinet Backplate Template for In-bottom/Out-back Cooling
AN371942757356en-000101 / 136R02528 | Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
1.
2.
3.
4.
5.
6.
e30bj235.10
352 (13.8)
11 (0.4)
12 (0.5)
163 (6.4) 188 (7.4)
8x Ø 7 (0.3)
Illustration 6: FA10 Cabinet Backplate Template for In-bottom/Out-back Cooling
2.5 Installing the Top Cover
To install the top cover of the cooling kit, use the following steps. See Illustration 7.
Procedure
Remove the paper backing from the top cover gasket to expose the adhesive.
Adhere the top cover gasket to the underside of the top cover.
Remove 8 M5x14 screws (T25) surrounding the sides and back of the vent in the top of the frequency converter. Retain the
screws.
Remove 3 M5x12 screws (T25) at the front of the vent in the top surface of the frequency converter.
Slide the edge of the top cover under the 3 loosened screws, positioning the cover over the vent in the top of the frequen-
cy converter.
Secure the top cover to the frequency converter with the M5x14 screws (T25) removed previously in step 3.
Torque all screws to 2.3 Nm (20 in-lb).
AN371942757356en-000101 / 136R0252 | 9Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
1.
2.
1
2
3
4
e30bj174.10
Illustration 7: Installation of the Top Cover
1
M5x14 screws
2
Top cover
3
Top cover gasket
4
Top vent
2.6 Creating a Vent Opening in the Base Plate
To create a vent opening in the base plate for the bottom duct, use the following steps. Use the dimensions in Illustration 8 for FA09
frequency converters, and Illustration 9 for FA10 frequency converters.
Procedure
Cut out the vent opening in the cabinet base plate using the dimensions in the template.
Drill 6 screw holes (4 mm) around the vent opening using the dimensions in the template.
The holes must match the holes in the lower flange of the bottom duct.
AN371942757356en-000101 / 136R025210 | Danfoss A/S © 2022.03
Installation
In-bottom/Out-back Cooling Kit for FA09-FA10
Installation Guide
Altri manuali per iC7 Series
20
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Danfoss Convertitore multimediale
Danfoss
Danfoss VLT 6000 Scheda tecnica
Danfoss
Danfoss VLT series Manuale utente
Danfoss
Danfoss VLT 2800 Series Manuale utente
Danfoss
Danfoss VLT 5000 Series Scheda tecnica
Danfoss
Danfoss iC7 Series Manuale utente
Danfoss
Danfoss VLT MCA 121 EtherNet/IP Manuale utente
Danfoss
Danfoss iC7 Series Manuale utente
Danfoss
Danfoss Vacon NXP Istruzioni per l’uso
Danfoss
Danfoss VLT AutomationDrive FC 301 Manuale utente
Danfoss
Danfoss 102 Manuale utente
Danfoss
Danfoss VLT AutomationDrive FC 300 Manuale utente
Danfoss
Danfoss VLT AutomationDrive FC 302 Manuale utente
Danfoss
Danfoss VLT HVAC Drive FC 102 Manuale utente
Danfoss
Danfoss Compressor Drive CD302 Manuale utente
Danfoss
Danfoss VLT 3500 HVAC Manuale utente
Danfoss
Danfoss VLT PROFIBUS DP MCA 101 Manuale utente
Danfoss
Danfoss VLT Manuale utente
Danfoss
Danfoss Vacon NXP Guida
Danfoss
Danfoss VLT Micro Drive FC 51 Series Manuale utente
Danfoss
Danfoss FC 100 Series Manuale utente
