Danfoss 176F6609 Manuale utente

Description

The ground bar kit ts the following drives in E1h and E2h

enclosures:

•

VLT

HVAC Drive FC 102

•

VLT

Refrigeration Drive FC 103

•

VLT

AQUA Drive FC 202

•

VLT

AutomationDrive FC 302

The kit includes a pair of ground bars for installation inside

E1h/E2h enclosures.

Kit Part Numbers

Use these instructions with the following kits.

Kit number Kit description

176F6609 Ground bar kit for E1h/E2h drives

Table 1.1 Part Numbers for Kits

Items Supplied

The ground bar kit contains the following items.

Item Quantity

Ground bar 2

Angle bracket 2

M5x18 mm screw 4

M6 hex nut 4

Table 1.2 Items Supplied in Ground Bar Kit

Safety Information

WARNING

ELECTRICAL SHOCK HAZARD

VLT

FC series drives contain dangerous voltages when

connected to mains voltage. Improper installation, and

installing or servicing with power connected, can cause

death, serious injury, or equipment failure.

To avoid death, serious injury, or equipment failure:

•

Only use qualied electricians for the installation.

•

Disconnect the drive from all power sources before

installation or service.

•

Treat the drive as live whenever the mains voltage

is connected.

•

Follow the guidelines in these instructions and local

electrical safety codes.

WARNING

DISCHARGE TIME

The drive contains DC-link capacitors, which can remain

charged even when the drive is not powered. High voltage

can be present even when the warning LED indicator lights

are o. Failure to wait 40 minutes after power has been

removed before performing service or repair work can result

in death or serious injury.

•

Stop the motor.

•

Disconnect AC mains and remote DC-link power

supplies, including battery back-ups, UPS, and DC-

link connections to other drives.

•

Disconnect or lock PM motor.

•

Wait 40 minutes for capacitors to discharge fully.

•

Before performing any service or repair work, use

an appropriate voltage measuring device to make

sure that the capacitors are fully discharged.

Installation Instructions

Ground Bar Kit for E1h/E2h Drives

VLT®FC Series FC 102, FC 103, FC 202, and FC 302

Installation Instructions

Installing the Ground Bar Kit

The ground bar kit includes 2 ground bars, 1 for the mains side and 1 for the motor side of the drive. To install the ground bars,

use the following steps. Refer to Illustration 1.1 to Illustration 1.3.

Illustration 1.1 Location of Ground Bar Mounting Holes in Midplate

Installation Instructions Ground Bar Kit for E1h/E2h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

1 M6 hex nut 5 Side view of assembled ground bar and bracket

2 Ground bar assembly for mains side 6 Front view of assembled ground bar and bracket

3 Angle bracket 7 Ground bar assembly for motor side

4 M5x18 mm screw 8 End view of assembled ground bar and bracket

Illustration 1.2 Assembly of Ground Bars and Angle Brackets

1. Attach the ground bars to the angle brackets:

1a Place 1 ground bar over the 2 threaded

posts on the angle bracket.

1b Fasten 2 M6 hex nuts (T30) to the bracket

posts, 1 on each post. See Illustration 1.2.

1c Tighten nuts to 3.9 Nm (35 in-lb).

1d Repeat for remaining ground bar and angle

bracket. Position ground bar with the long

end oriented in the opposite direction on

Installation Instructions Ground Bar Kit for E1h/E2h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

the bracket. When correctly assembled, the

2 grounhd bars mirror each other.

2. Remove 4 screws from the mounting holes in the

midplate, 2 from each side of the drive. For the

location of the mounting holes, see Illustration 1.1.

3. Position the 2 angle brackets with attached ground

bars over the mounting holes in the midplate. See

Illustration 1.3.

4. Fasten angle brackets to the midplate with 4 M5x18

mm screws (T25) from the kit, 2 in each angle

bracket. Tighten to 2.3 Nm (20 in-lb).

1 Mains side ground bar installed 2 Motor side ground bar installed

Illustration 1.3 Ground Bars and Angle Brackets Installed

Installation Instructions Ground Bar Kit for E1h/E2h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

Installation Instructions Ground Bar Kit for E1h/E2h Drives

VLT

FC Series FC 102, FC 103, FC 202, and FC 302

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on

order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss

Danfoss A/S

Ulsnaes 1

DK-6300 Graasten

vlt-drives.danfoss.com

*MI35K102*

MI35K102130R0763 10/2017

Altri manuali Danfoss Servoazionamento

Danfoss

Danfoss 176F6491 Manuale utente

Danfoss

Danfoss VLT Midi Drive FC 280 Manuale utente

Danfoss

Danfoss 176F6764 Manuale utente

Danfoss

Danfoss VLT Integrated Servo Drive ISD 510 System Manuale utente

Danfoss

Danfoss VLT ISD Connection Box Manuale utente

Danfoss

Danfoss 176F6748 Manuale utente

Danfoss

Danfoss VLT HVAC Drive FC 102 Guida

Danfoss

Danfoss 176F3530 Manuale utente

Danfoss

Danfoss 176F6493 Manuale utente

Danfoss

Danfoss 176F6494 Manuale utente

Danfoss

Danfoss VLT FC 103 Manuale utente

Danfoss

Danfoss AME 25 Manuale utente

Danfoss

Danfoss VLT AutomationDrive FC 360 Manuale utente

Danfoss

Danfoss VLT 6002-6011 Manuale utente

Danfoss

Danfoss 176F3166 Manuale utente

Danfoss

Danfoss VLT Integrated Servo Drive ISD 510 System Manuale utente

Danfoss

Danfoss VLT Integrated Servo Drive ISD 510 System Guida

Danfoss

Danfoss VLT AutomationDrive FC 302 Manuale utente

Danfoss

Danfoss AMV 655 Manuale utente

Danfoss

Danfoss VLT series Istruzioni operative

Danfoss

Danfoss VLT AQUA Drive FC 200 Istruzioni operative

Danfoss

Danfoss VLT ISD 410 Manuale utente

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuale utente

Danfoss

Danfoss 176F6489 Manuale utente

Manuali Servoazionamento popolari di altre marche

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuale utente

Robotis

Robotis XH430-W350-T Manuale utente

NTI AG

NTI AG LinMot C1250 Series Manuale utente

Welcon

Welcon WE2A D048 Series Manuale utente

Parallax

Parallax 900-00005 Manuale utente

Festo

Festo TP 1410 Manuale utente

Axor

Axor MAGNUM 400 Manuale utente

Siemens

Siemens SINAMICS S120 Manuale utente

THORLABS

THORLABS TDC001 Manuale utente

TECO

TECO JSDAP Series Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 6000 Manuale utente

GSK

GSK DA98D Manuale utente

Lenze

Lenze m850 Guida

Baumuller

Baumuller b maXX 3000 Manuale

Baumuller

Baumuller b maXX 5000 Manuale

Baumuller

Baumuller b maXX 5500 Manuale

Omron

Omron CK5M-CPU 1 Series Guida utente

ABB

ABB ACS350 Series Manuale utente