Danfoss RET2000 B Manuale utente
RET2000 B
Electronic digital thermostat with LCD
User Guide
Danfoss Heating
RET2000
2
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other
printed material. All trademarks in this material are property of the respective companies.
Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss Heating 3
GB
GB
Thank you for buying a Danfoss product GB
FR
ES
Le agradecemos que haya comprado un producto de
Danfoss
Merci d’avoir choisi un produit Danfoss
RET2000
4
GB
FR
ES
GB
What is a room thermostat?
... an explanation for householders. A room thermostat simply switches
the heating system on and o as necessary. It works by sensing the
air temperature, switching on the heating when the air temperature
falls below the thermostat setting, and switching it o once this set
temperature has been reached.
Turning a room thermostat to a higher setting will not make the
room heat up any faster. How quickly the room heats up depends on
the design of the heating system, for example, the size of boiler and
radiators.
Neither does the setting aect how quickly the room cools down.
Turning a room thermostat to a lower setting will result in the room
being controlled at a lower temperature, and saves energy.
Danfoss Heating 5
GB
ES
FR
GB
The heating system will not work if a timeswitch or programmer has
switched it o.
The way to set and use your room thermostat is to nd the lowest
temperature setting that you are comfortable with, and then leave it
alone to do its job.The best way to do this is to set the room thermostat
to a low temperature – say 64°F – and then turn it up by one degree
each day until you are comfortable with the temperature. You won’t
have to adjust the thermostat further. Any adjustment above this
setting will waste energy and cost you more money.
If your heating system is a boiler with radiators, there will usually
be only one room thermostat to control the whole house. But you
can have dierent temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
haveTRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting theTRVs.
Room thermostats need a free ow of air to sense the temperature,
so they must not be covered by curtains or blocked by furniture.
Nearby electric res, televisions, wall or table lamps may prevent the
thermostat from working properly.
RET2000
6
GB
FR
ES
GB
Display
The LCD displays actual room temperature until the Λ or V button
is pressed more than once. To activate the unit’s backlight press
the Λ or V button once, if no further buttons are pressed the
backlight will remain on for 6 seconds.
Temperature
Danfoss Heating 7
GB
ES
FR
GB
Flame: shows when heating output is on
(in heating mode only)
Standby: shows when unit is manual set to standby
Snowake: shows when cooling output is on
(in cooling mode only)
Battery: ashes when battery is low (battery units only)
Padlock: indicates keyboard lock has been set at
installation
RET2000
8
GB
FR
ES
GB
Thermostat status (heat mode only)
A ame symbol will be lit whenever the thermostat is calling for
heat.
Setting the temperature
Press either the Λ or V buttons, the product backlight will come
on.
Press either the Λ or V button again within 6 seconds, the display
will ash with the current set temperature. While the display is
ashing press the Λ arrow to increase the set temperature to the
required setting or the V arrow to decrease the set temperature.
If no buttons are pressed the display will return to actual
temperature after 4 seconds and the backlight will go out after
6 seconds.
Danfoss Heating 9
GB
ES
FR
GB
Thermostat status (cool mode only)
A snowake symbol will be lit whenever the thermostat is calling
for cooling. If this is seen to ash, the thermostat output is
delayed for a short period to prevent compressor damage.
Thermostat standby
To place the thermostat into standby (o), press the V arrow
twice to enter the temperature setting mode. When in heating
mode press and hold the V arrow until the set temperature
disappears and the standby symbol appears. In cooling mode
press and hold the Λ arrow until the standby symbol appears.
When in standby the thermostat will have no control of the
heating or cooling system.
To exit standby press and hold the Λ arrow (V arrow in cooling
mode) until the required set temperature is ashing on the
display.
RET2000
10
GB
FR
ES
GB
Low Battery Indications
When the batteries require replacement the battery low symbol
will ash. Batteries should be replaced within 15 days, after
which the thermostat will turn o the load it is controlling. If
the display does not illuminate the batteries may have expired
and should be replaced immediately to avoid damage to the
thermostat
Altri manuali per RET2000 B
2
Indice
Lingue:
Altri manuali Danfoss Termostato
Danfoss
Danfoss Icon Master Manuale utente
Danfoss
Danfoss TP9000 Guida
Danfoss
Danfoss DEVIreg 531 Manuale utente
Danfoss
Danfoss DEVIreg Opti Manuale utente
Danfoss
Danfoss Link DBR Manuale utente
Danfoss
Danfoss 088L5130 Manuale utente
Danfoss
Danfoss KPU 61 Manuale utente
Danfoss
Danfoss ST-D1 Manuale utente
Danfoss
Danfoss ECL Comfort 210 Manuale utente
Danfoss
Danfoss Icon Master Manuale utente
Danfoss
Danfoss TPONE-RF Manuale utente
Danfoss
Danfoss Eco Manuale utente
Danfoss
Danfoss DEVIreg 330 Manuale utente
Danfoss
Danfoss CF-RP 088U0211 Manuale utente
Danfoss
Danfoss DEVIreg Opti Manuale utente
Danfoss
Danfoss RET2000 M Manuale utente
Danfoss
Danfoss DEVI DEVIreg 532 Manuale utente
Danfoss
Danfoss RMT-230 Manuale utente
Danfoss
Danfoss DEVIreg 233 Manuale utente
Danfoss
Danfoss C37 Manuale utente
