Danfoss TP5000 RF Si Guida
TP5000 + RF
GB
F
D
ES
DK
NL
G
LT
P
I
Installation Instructions
User Instructions
Instructions d’installation
Instructions d’utilisateur
Installationsanweisungen
Inbetriebnahme-Instruktion
Instrucciones de instalación
Instrucciones del usuario
Instruktions vejledning
Brugervejleding
5/2 day programmable electronic room thermostat
Installatie handleiding
Instructiesevoor Gebruik
Ïäçãßåò åãêáôÜóôáóçò
Ïäçãßåò ÷ñÞóçò
Instrukcja instalacji
Instrukcja Użytkownika
Montavimo instrukcijos
Informacija Vartotojui
Istruzioni per l’uso
Istruzioni per l’utente
2
INDEX
Installation Instructions 3-6
User Instructions 7-12
Instructions d’installation 13-16
Instructions d’utilisateur 17-22
Installationsanweisungen 23-26
Inbetriebnahme-Instruktion 27-32
Instrucciones de instalación 33-36
Instrucciones del usuario 37-42
Instruktions vejledning 43-46
Brugervejleding 47-52
Installatie handleiding 53-56
Instructiesevoor Gebruik 57-62
Ïäçãßåò åãêáôÜóôáóçò 63-66
Ïäçãßåò ÷ñÞóçò 67-72
Instrukcja instalacji 73-76
Instrukcja Użytkownika 77-82
Montavimo instrukcijos 83-86
Informacija Vartotojui 87-92
Istruzioni per l’uso 93-96
Istruzioni per l’utente 97-102
F
D
ES
DK
NL
G
P
LT
I
3
Installation
Instructions GB
Important note RF products: Ensure that there are no large metal objects, such
as boiler cases or other large appliances, in line of sight between the transmitter
and receiver as these will prevent communication between thermostat and receiver.
Product Specification
GB - Installation Instructions
Please Note:
This product should only be installed by a
qualified electrician or competent heating
installer and should be in accordance with the
current edition of the IEEE wiring regulations.
Thermostat features TP5000 TP5000-RF
Power supply 2 x AA/MN1500/LR alkaline cells
Memory back-up 1 min for battery change
Switching action of output relay
1 x SPDT, Type 1B
N/A
Switch rating of relay contact 6(2)A, 10-230Vac N/A
Transmission frequency (RF model) N/A 433.92MHz
Transmitter range (RF model) N/A 30m max
Temperature range 5-30°C
Dimensions, mm 110 wide, 88 high, 28 deep
Design standard EN60730-2-9 (EN300220 for RF)
Rated impulse voltage 2.5Kv
Ball hardness test 75°C
Control pollution situation Degree 2
Temperature accuracy ±1°C
Time accuracy ±1 min.
4
GB - Installation Instructions
Installation
First, remove the wallplate from the back of the unit.
From the top left hand corner of the wallplate, there must
be clearances of at least 140mm to the right, 15mm to
the left, 30mm above and 100mm below in order to
mount the plug-in module.
Fix at a height of approximately 1.5m from the floor,
away from draughts or heat sources such as radiators.
open fires or direct sunlight.
Prior to mounting the unit should be set in either ON/
OFF or chrono-proportional control mode (see below).
1) ON/OFF - boiler switches ON when below set temperature
and OFF when above..
1) ON/OFF 2) CHRONO
5
!
GB - Installation Instructions
2) Chrono-Proportional - energy saving feature which fires
the boiler at regular intervals to maintain a set temperature,
achieving a constant ambient environment for the user.
For a full explanation of all advanced features please
visit our website www.danfoss-randall.co.uk or call 01234
364621 to obtain a copy of our Advanced Features Guide.
Thermostat Wiring (not RF models)
Some existing thermostats will have a Neutral and/or Earth wire connected.
These are not required by the TP5000 and must NOT be connected to any
TP5000 terminals. Instead they should be made electrically safe and coiled
in the recess at the back of the TP5000.
RX1 & RX2 RX3
RX1 & 2 (3055 12/01)
COM
RX3 (3056 12/01)
RX Receiver Wiring (RF models only)
NB. For mains voltage operated systems link terminal 2 to mains live supply
6
Commissioning (RF models only)
GB - Installation Instructions
To tune the RX receiver to the frequency of the thermostat signal,
follow steps 1-5 below.
Step 1 TP5000-RF
Reset the unit by pressing and holding
-, +, V and together until display goes blank.
Step 2 Press and hold V and +
buttons for 3 seconds
(TP5000 now transmits
unique signal continuously
for 5 minutes)
Step 3 RX1
Press and hold buttons
PROG and CH1 for
3 seconds until green light
flashes once.
Step 4 RX2 (if applicable)
Stat 1 - perform steps 1-3
Stat 2 - wait 5 mins, perform steps 1-2 and then
press PROG and CH2 on RX2
RX3 (if applicable)
Stat 1 - perform steps 1-3
Stat 2 - wait 5 mins, perform steps 1-2 and then
press PROG and CH2 on RX3
Stat 3 - wait 5 mins, perform steps 1-2 and then
press PROG and CH3 on RX3
Step 5 TP5000-RF
Press V or to select temperature - the unit will
revert back to operating mode.
7
Your programmable room thermostat
The TP5000 allows you to programme up to 6 times and
temperatures at which your heating will come on and go
off each day. You can programme one set of times and
temperatures for weekdays and another set for weekends.
It features several user overrides including frost protection,
thermostat mode and time or temperature display.
Preset Programmes
Your TP5000 comes ready programmed with a set of operating
times and temperatures which often suit most people.
If you want to change any of these settings you can do so by
following the instructions on pages 9-10.
First, follow the steps on page 8 to set the correct time and date.
GB - User Instructions
Weekdays (Mon-Fri) Weekend (Sat-Sun)
Event Time Temp °C Event Time Temp °C
1 06:30 20 1 07:00 20
2 08:30 15 2 16:00 21
3 11:30 20 3 23:00 15
4 13:30 15 4 00:00 15
5 16:30 21 5 01:00 15
6 22:30 15 6 01:59 15
User Instructions
GB
8
Before you start
Open the flap on the front of the
programmer.
Press the + & – AND & buttons
simultaneously to reset the unit.
This will reinstate the preset
programmes and will set the time to
12:00 on Day 1 and the temperature
to 20°C.
Setting the Clock & Day
Note: clock is displayed in 24 hour mode
CLOCK
Press PROG to begin programming.
Use + or - to adjust the TIME
(press and hold to change in 10 min
increments)
DAY
Press PROG again.
Use + or - buttons until correct DAY is
shown (1 = Monday, 2 = Tuesday, etc)
Remember - you will have to
reset the time when the clocks
change in Spring and Autumn.
i2 00
!
GB - User Instructions
9
GB - User Instructions
Please Note
The unit must be programmed in sequence and ON/OFF
times cannot be programmed out of sequence.
If you want to leave a preset time as it is, simply press
PROG to move on to the next setting.
During programming, if no buttons are pressed for 2 to 3
minutes the unit will automatically return to RUN mode,
and the programme set up to that minute will be active.
If at any time you get confused and need to reset
the unit to the preset programmes press the
+ & – AND &buttons simultaneously.
20
i2 24
Before you change the preset programmes
!
Running your programme
If you are happy to use the preset programmes on page 7,
you don’t need to do anything else.
To accept the presets close the front cover
and after 2 minutes the presettings will
automatically be accepted (& colon will blink).
Your unit is now in RUN mode.
10
For Days 1-5 (weekdays)
a) Press PROG until 1st pre-set time
and temperature (Event 1, Days
1,2,3,4,5) appears in display.
b) Use + or – buttons to adjust the
TIME (press and hold to change in
10 min increments)
c) Use or buttons to adjust the
TEMPERATURE.
d) Press PROG to move to next preset
time & temperature (Event 2)
e) Repeat steps b, c & d for
programming Events 3, 4, 5 & 6.
For Days 6-7 (weekends)
Press PROG until 1st pre-set time
and temperature (Event 1 Days
6-7) appears in display.
Repeat steps b, c and d above to
programme time and temperature
events for the weekend.
Changing the preset programmes
20
1
6 30
15
2
8 30
20
1
7 00
GB - User Instructions
If you require just 2 Events per day (1 ON / 1 OFF)
Follow steps a, b & c above to programme
Event 1 (ON)
Press and hold and - buttons together
for 3 seconds to skip events 2,3,4 & 5.
Follow steps b & c to programme Event 6 (OFF)
To revert back to six events per day, reset the thermostat
(see page 8).
Altri manuali per TP5000 RF Si
1
Indice
Altri manuali Danfoss Termostato
Danfoss
Danfoss ECtemp Smart Manuale utente
Danfoss
Danfoss CF-RP 088U0211 Manuale utente
Danfoss
Danfoss TP9000 Manuale utente
Danfoss
Danfoss RT 115 Manuale utente
Danfoss
Danfoss ECtemp Next Plus HW Manuale utente
Danfoss
Danfoss TP75H Manuale operativo
Danfoss
Danfoss Icon Wireless Dial Manuale utente
Danfoss
Danfoss ECtemp 535 Manuale utente
Danfoss
Danfoss SET 3E Manuale utente
Danfoss
Danfoss DEVI DEVIreg 532 Manuale utente
Danfoss
Danfoss ECtemp 316 Manuale utente
Danfoss
Danfoss HP8211-1RJ Manuale utente
Danfoss
Danfoss DEVIreg 610 Manuale utente
Danfoss
Danfoss 088L5130 Manuale utente
Danfoss
Danfoss DEVIreg 330 Manuale utente
Danfoss
Danfoss ECtemp 330 Manuale utente
Danfoss
Danfoss Link FT Manuale utente
Danfoss
Danfoss RT 14E Manuale utente
Danfoss
Danfoss ECtemp 530 Manuale utente
Danfoss
Danfoss DEVI DEVIreg Touch Manuale utente
