DAQ system USB-AIO10 Manuale utente
USB-AIO10 User’s Manual (Rev 1.1)
-1-
http://www.daqsystem.com
USB-AIO10
User’s Manual
Windows, Windows2000, Windows NT, Windows XP, Windows 7 and Windows CE are trademarks of Microsoft. We
acknowledge that the trademarks or service names of all other organizations mentioned in this document as their own property.
Information furnished by DAQ system is believed to be accurate and reliable. However, no responsibility is assumed by DAQ
system for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under any patent or copyrights of DAQ system.
The information in this document is subject to change without notice and no part of this document may be copied or
reproduced without the prior written consent.
Copyrights 2017 DAQ System Co., LTD. All rights reserved.
USB-AIO10 User’s Manual (Rev 1.1)
-2-
http://www.daqsystem.com
Contents
1. Introduction
1.1 Function
1.2 Internal Block Diagram
2. Product Features
3. Installation
3.1 Package Contents
3.2 Installation Sequence
4. Hardware Device
4.1 Reset Switch(SW1)
4.2 USB Connector(CN1)
4.3 Power Selection Connector(J1)
4.4 External Power Connector(J2)
4.5 RS-232 Connector(J16)
4.6 Digital InputㆍOutput Circuit
4.7 Output Signal Connector(J9)
4.8 Input Signal Connector(J3)
4.9 Analog Signal Selection Connector
4.9.1 Analog Input Mode Selection
4.9.2 Analog Output Mode Selection
USB-AIO10 User’s Manual (Rev 1.1)
-3-
http://www.daqsystem.com
5. Sample Program
5.1 USB Interface Sample Program
5.1 RS-232 Interface Sample Program
References
(Caution)
★The board and external input/output signals of the device have
to connect the common ground(Frame) to protect the board and
peripheral devices.
★The board operates in a safe location, in a clean environment.
★External connection is completed before board power
connection, the function should be run by the rated power.
USB-AIO10 User’s Manual (Rev 1.1)
-4-
http://www.daqsystem.com
1. Introduction
USB-AIO10 is the function board to support Analog Input·Output, Digital Input·Output, USB 2.0
High Speed, RS-232 communication interface.
It supports the voltage, current Input/Output mode for Analog signals, shield the Digital Interface.
Basically, the board operation can use 5VDC external power, and optionally you can use USB
power.
1.1 Function
-4-Ch 16-Bit Analog Input
-4-Ch 16-Bit Analog Output
-Support Analog Voltage/Current Mode
-Isolated 24-Bit Digital Input/Output
-USB 2.0 High Speed Interface
-RS-232 Interface
1.2 Internal Block Diagram
FPGA
ADC DAC
Analog IN
4-Channel AIN
Signal
Condition
USB
Controller
AOUT
Signal
Converter
Analog OUT
4-Channel
USB Interface
DOUT
Isolator
DIN
Isolator
Digital IN
24-Channel Digital OUT
24-Channel
Serial
Transceiver RS-232
1-Channel
[Figure 1-1. Internal Block Diagram]
USB-AIO10 User’s Manual (Rev 1.1)
-5-
http://www.daqsystem.com
2. Product Features
[Table 1. Specification]
List
Specification
External Interface Connector
USB B-type Connector
Output D-SUB Connector for Analog/Digital Input/
RS-232 D-SUB Connector
5VDC Power Connector
Analog Input(AD)
Channel : 4
Maximum Input Range : 0~+5V, 0~20mA
Resolution : 16-bit, Simultaneous ADC
Maximum Sampling : 52,734 Sample/sec
Voltage, Current Mode Setup
Analog Output(DA)
Channel : 4
Maximum Output Range : 0~+5V, 0~20mA
Resolution : 16-bit DAC
Maximum Set Time : 10usec
Voltage, Current Mode Setup
Digital Input
Channel : 24 Input
Input Signal Level: 12/24VDC Isolated
No-polarity Input
Digital Output
Channel : 24 Output
Output Signal Level: 12/24VDC Isolated
Polarity Output
Data Interface
USB 2.0 High Speed(480Mbps)
RS-232 115,200bps 8-bit data, 1-bit parity
Board Size
151x110mm(Except Connector)
Operation Temperature
Operation Humidity
Operation Power
5VDC±10%, 200~400mA
Application
Kernel mode WDM Driver/User mode DLL
OS
Windows 2K/XP/7 32-bit
Basic Components
USB-AIO10 Card, USB A-B Cable,
Installation CD(Driver/Manual/Sample Source etc.)
Related Products
Base-DB37 Extension Board(Separately)
Etc.
To use a USB-powered, and a stable analog input and
USB-AIO10 User’s Manual (Rev 1.1)
-6-
http://www.daqsystem.com
output for external power supply (5VDC, over 500mA)
is required.
USB-AIO10 User’s Manual (Rev 1.1)
-7-
http://www.daqsystem.com
3. Installation
Explains how to install the USB-AIO10 to PC and check the device.
3.1 Package Contents
After unpacking, inspect the board carton to make sure there are no damages on the board.
-USB-AIO10 Board
-USB(A-B) Cable
-Installation CD (Driver/Manual/API/Sample Source etc.)
3.2 Installation Sequence
To install USB-AIO10 board in your environment, do the following steps. The USB-AIP10 board
is completely Hot-Plug and Plug & Play. Therefore, you can install it easily.
The required PC operating system for the USB-AIO10 is Windows 2000 SP4 or Windows
XP/7/10.
(1) Install the USB-AIO10 board into your system.
(2) Connect USB A-B cable between the case and your PC.
The Add New Hardware Wizard will appear in order to install the driver for new hardware.
(3) The Add new Hardware Wizard will install the driver in the following process. The following
install process is explained based on Windows 7 operating system.
USB-AIO10 User’s Manual (Rev 1.1)
-8-
http://www.daqsystem.com
(4) If new hardware is found, Wizard will ask you to install the corresponding driver. To install the
driver in the above figure, select "Browse the driver software on your computer (R)" and
press the Next button. The following driver search screen will appear.
In the figure above, click the Browse button on the Driver folder of the CD that contains the
driver, specify the 32/64 bit of the operating system to be used, and then click the "Next" button.
Select the folder where the drivers are located. Click “OK”. Click “Next”.
The necessary files are “usb_aio10.inf” and “usb_aio10.sys” in the driver folder.
USB-AIO10 User’s Manual (Rev 1.1)
-9-
http://www.daqsystem.com
(5) If the board that is found has the appropriate driver, click "Install this driver software" to start
the installation.
(6) When the installation is completed normally, the following message window appears.
USB-AIO10 User’s Manual (Rev 1.1)
-10-
http://www.daqsystem.com
(7) If the installation is completely finished, you confirm it in the following ways. Do the following
steps to show up the “Device Manager” window. [My Computer -> properties -> Hardware ->
Device Manager -> Universal Serial Bus Controller -> “DAQ System Analog Input/Output
Board”]
If you can see the “DAQ System USB2.0 Multi-Function Board” at Universal Serial Bus
Controller, the driver installation is to have been over. (Check the red circle)
Notice : After installation, you should re-boot the system for the proper operation.
Indice
Altri manuali DAQ system Scheda PCI
DAQ system
DAQ system PCIe-OPT01 Manuale utente
DAQ system
DAQ system PCIe-HDMI01 Manuale utente
DAQ system
DAQ system PCIe-HDMI01 Manuale utente
DAQ system
DAQ system PCIe-FRM11 Manuale utente
DAQ system
DAQ system PCI-AIO05 Manuale utente
DAQ system
DAQ system PCIe-AIO15 Manuale utente
DAQ system
DAQ system PCIe-FRM24 Manuale utente
DAQ system
DAQ system PCI-AIO01 Manuale utente
DAQ system
DAQ system PCIe-AIO14 Manuale utente
DAQ system
DAQ system PCI-DIO02 Manuale utente
DAQ system
DAQ system PCIe-FRM11 Manuale utente
DAQ system
DAQ system PCI-DIO6402 Manuale utente
DAQ system
DAQ system PCIe-DIO6400 Manuale utente
DAQ system
DAQ system PCIe-DIO02 Manuale utente
DAQ system
DAQ system PCIe-DIO13 Manuale utente
DAQ system
DAQ system PCI-PWM02 Manuale utente
DAQ system
DAQ system USB3-FRM20 Manuale utente
DAQ system
DAQ system PCI-DIO02 Manuale utente
DAQ system
DAQ system NET-AIO12 Manuale utente
DAQ system
DAQ system USB3-FRM13-K Manuale utente
