DaSeDa Electronics HM-75A Manuale utente
Manual
Digital Feeder Controller : HM-75A/710A
1. HM-75A / 710A controller front configuration
1. Data display window: Displays frequency, voltage, parameter, error code, etc. in numeric or text
2. RUN LED: It lights up during RUN, blinks during pause, and turns off at STOP.
3. Feed Back LED: It is ON when Feed Back ON and Sensor is connected.
Flickering when setting the vibration amount reference value, ON while the constant amplitude function is operating.
4. RUN Key: Pressing RUN key for a short time.
5. Volume: Used to change voltage / frequency / parameter value. Press repeatedly to select frequency / voltage repeatedly
6. STOP Key: Short press to stop the operation (STOP), press this button to initialize the controller when POWER ON. (See initializing the controller)
7. Selector: Frequency / Voltage / Parameter, etc. For setting menu selection, parameter value is displayed when button is pressed, and value can be changed by volume (1).
8. Power Key: Controller power switch.
9. Frequency LED: On when frequency is set.
10. Volt LED: On when voltage is set.
11. Slow Start LED: On when parameter Slow Up / Down time is set.
12. Sensor LED: On when parameter related to sensor is set. (Number of Sensors, On / Off Delay Time, NO / NC)
13. Ext Input LED: On when parameter related to external input is set. (On / Off Delay Time, NO / NC)
14. Feed Back LED: Turns on when setting parameters related to vibration such as constant amplitude control and constant amplitude time.
15. Ext Volume LED: Turn on when using external volume ON / OFF.
2. Power and feeder connection
- Internal connectors AC1 and AC2 are internally connected to each other and can be used to supply power to other controllers
Is a power connection method when two additional controllers are connected.
- Ground the feeder.
3. External input
- Used for operation and stop with external input.
- Control method is as follows.
3-1. Contact control method 3-2. TR control method
3-3. Voltage control method
E-nc
stop
driving
stop
driving
OPEN
12~24V
0 V
Condition E-no
driving
stop
driving
stop
Direct
connection
(3-1, 3-2)
Voltage input
(3-3)
CLOSE
4. External input 2CHANNEL
'- The output voltage can be controlled in two ways by the 2CHANNEL input. (You have to go to V2 ON in Paris Meter.)
- V1 if there is no input, V2 if there is input
4-1. Contact control method 4-2. TR control method
5. External volume
Function to control output voltage by applying volume or voltage to external terminal
5-1. Volume control method
5-2. Voltage control method
Do not exceed 5V DC
6. Sensor operation control
- The HM-75A / 710A controller can be operated / stopped by an external sensor.
- One to three sensors can be used depending on parameter setting.
6. Sensor operation control 6-2. When using two sensors
7. Vibration sensor
- In order to maintain constant vibration amplitude during operation, attach a vibration sensor to the feeder
Set the constant amplitude control ON in the parameter setting.
7-1. How to connect vibration sensor
Vibration sensor should be connected to its own product. (Third-party products are not allowed.)
8. DATA communication
- Transmit controller status and control data by external data communication with external control device (PLC, computer ..).
- Communication method is 485 method. Up to 32 cables can be connected to one communication cable. (Refer to communication manual)
- Connect to SERIAL on one line.
- Each HM-75A controller has two communication connectors, which are internally connected to each other in parallel,
For convenient connection.
- The communication cable uses shielding wire with three wires.
9. Connection of operation synchronous output signal
9-1. Operation synchronous contact signal
- This controller has a function to give synchronization signal to control other external controller.
When stopping or pausing, the contact signal is sent to 8, 9, and the contact signal is output to 9, 10 during operation.
This can be used as an operation / stop signal for another controller (HOPPER, etc.).
- The figure below shows a connection diagram between a hopper (HOPPER) and a ball (BOWL) controller.
9-2. AC220V output for SOL drive
10. How to operate the controller
10-1. Power on / off method
This controller is a push (push) type, not a lock type.
With the AC cord plugged in
To turn on the power first, press and hold the power switch (for about 1 second)
The power turns on while it is on.
To turn off the power Turn on the power switch while the power is on in the same way
Press and hold for about 1 second to turn off the power while the display is enlarged.
In the ideal state, the button is not operated and the output is not output.
10-2. Initialize the controller
DSD_75A can initialize various parameters by button operation.
After turning off the power and holding down the "stop" button and pressing the power button to turn on the display
The power button can be released, but the "stop" button is held down for 3 seconds.
On the display
All values are initialized while flashing 3 times.
10-3. Parameter change prevention setting and cancellation
The DSD_75A controller can be set to lock the system so that it can not change various parameters such as frequency and voltage.
It is possible to prevent the setting value from being changed unintentionally when the button in use is mistakenly touched.
OFF is set in initialization. If it is set to OFF, the parameter can be changed, but if it is .
ON, the setting value will not be changed even if the volume is turned.
- To set ON, press the "RUN" button for 3 seconds while the power is on
The display flashes for 3 seconds to prevent the parameter change and turn the volume
The left-hand side flashes for 3 seconds, indicating that the current lock is in progress.
- To release the lock device again, press the "RUN" button for 3 seconds
The display flashes for 3 seconds to release the lock
You can change the parameters
10-3. Parameter setting menu
You can select the parameter change menu by turning the selector.
Turn the selector to the right
Frequency -> voltage 1 -> slow up -> slow down -> number of sensors -> sensor polarity -> sensor on delay ->
Sensor off delay -> external input polarity -> external input on delay -> external input off delay -> external volume on / off
-> Constant amplitude control on / off -> Constant amplitude control time -> Voltage 2 on / off -> Voltage 2 -> Communication id setting
-> Automatic frequency setting -> Controller version display.
Turning to the left selects the opposite.
menu Setting range Initial value Menu LED
Display Show menu Pressing the selector button or
Show setting value when turning
Frequency 40 ~ 400Hz
(
0.1Hz unit
)
120Hz Frequency
Volt 1 0 ~ 200V
(
0.1V 단
위
)
100V Volt
slow up 0 ~ 3sec
(
0.1sec unit
)
0.1 sec Slow Start
slow down 0 ~ 3sec
(
0.1sec unit
)
0 sec Slow Start
Number of used sensors 1 ~ 2 1 EA Sensor
Sensor polarity setting no,nc no Sensor
sensor
on dela
y
0 ~ 60sec
(
0.1sec unit
)
0.1 sec Sensor
센서
off dela
y
0 ~ 60sec
(
0.1sec unit
)
0.1 sec Sensor
External input
Polarit
y
settin
g
no,nc no Ext Input
Ext input
on dela
y
0 ~ 60sec
(
0.1sec unit
)
0 sec Ext Input
Ext input
off dela
y
0 ~ 60sec
(
0.1sec unit
)
0 sec Ext Input
Vibration control
on
/
off on, off off Feed Back
Vibration Width
Control time
10 ~ 1000
(
10 unit
)
300 Feed Back
External volume on, off off Ext Volume
V2 on/off on, off off Volt
Volt 2 0 ~ 200V
(
0.1V unit
)
50V Volt
Communication ID setting 0 ~ 32
(
0 = off
)
off
frequency
Automatic setting
Selector button
Press to start.
Show product version
If there is no button or volume operation for 20 seconds after setting is completed, or when RUN or STOP button is pressed
The display shows the default output voltage.
"Volt LED ON"
Questo manuale è adatto per i seguenti modelli
1
Indice
