DataComm Electronics IWPE2-TV-7FT Manuale utente
Instruction/Installation Sheet for In-Wall Power Extension Kits (6623)
DataComm Electronics
6349 Peachtree St.
Norcross, GA 30071-1725
888.223.7977
www.datacommelectronics.com
Parts Included:
1. Pre-Assembled TopPlate w/ 15A / 125V duplex
receptacle/ female connector
2. Pre-Assembled Bottom Plate w/ female connector
3. In-Wall Power Cord w/ two male connectors &
strain relief
4. 3ft. extension cord w/ 360ºrotating flat head
Tools Needed:
1. Drywall Saw
2. 6 ft. Tape Measure
3. Pencil
4. Phillips Head Screwdriver
IMPORTANT INSTRUCTIONS:
•
Always follow local electrical code when installing this product.
•
The electrical parts in this kit are designed to be used only as a kit and none of these electrical parts are designed to be used
individually.
•
This product is not designed to be part of your home or a commercial building’s electrical wiring system.
•
This installation is only energized (electrically active) when the supplied 6 ft. cord is plugged into the recessed straight blade
inlet (located on the recessed low voltage cable plate) and the straight blade end of the 6 ft. cord is plugged into either your
surge protector or wall receptacle.
•
This product is designed for retrofit work only because the electrical outlet box cannot be attached to a stud.
If you are not familiar with home wiring systems, please call a qualified electrician to install this product.
WARNING:
•
DataComm Electronics’ products shall be installed and used only as indicated in DataComm Electronics’ product instruction sheets.
•
Instruction sheets are available online at www.datacommelectronics.com
CAUTION:
•
For shock protection, this device must be properly grounded.
•
Use copper wire only with this device.
IMPORTANT INSTRUCTIONS:
•
Read and understand all instructions.
•
Follow all warnings and instructions marked on the product.
•
Do not use this product near water, for example; near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming
pool.
•
SAVE THESE INSTRUCTIONS Page 1 of 3 11/05/2018
N Figure 1: Top view - shows needed space between the drywall and the studs. The
power output plate should be centered between the studs.
Figure 2: Using the template supplied (see page 3of instruction sheet), trace the opening for both the top
and bottom plate. See Figure 1 before tracing your opening. Remember, the plates are designed to be
mounted centered between the studs. Using a drywall saw, cut a hole in the drywall the size of each template.
Figure 3: Using a Philips screwdriver, secure male end of the in-wall connector to the female end that is attached
to the top plate using the included metal strain relief and screws.
Figure 4: Run your low voltage cables and the included 14/2 with ground UL approved electrical building wire from
the top opening in the wall through the bottom opening in the wall. You will need to fish the cables from the top
opening to the bottom opening.
Stop: Important: Before installing the top power plate into the top template opening, make sure to pull your low
voltage cables through the low voltage cable opening at the back of the plate.
Figure 5: After inserting your low voltage cables and the electrical building wire through the opening for the top
plate, install the top plate into the wall by inserting the electrical work box into the wall first (see Figure 5).
Slowly slide the top power plate into the opening. Swing the top of the plate into position until the entire plate is
flush against the wall.
Figure 6: Using a Phillips screwdriver, tighten the screws with wings. These wings fasten tightly against the back
of the wall.
Note: Do not overtighten screws.
Figure 7: Pull cables out of bottom opening in the wall. Using a Phillips screwdriver, secure the male end of the in-
wall connector to the female end that is attached to the bottom plate using the included metal strain relief and
screws.
Figure 8: Stop: Important: Before installing the bottom recessed plate with inlet into the bottom template
opening, make sure to pull your low voltage cables through the low voltage cable opening in the back of the plate.
After you have pulled your low voltage and audio/video cables through the bottom power input plate, insert the
side of the plate with the electrical work box into the wall. (see Figure 8). Swing the right side of the plate into
position until the entire plate is flush against the wall. Now tighten the screws with wings. These wings fasten
tightly against the back of the wall. Note: Do not overtighten screws.
Figure 9: Now hang your flat panel TV on the mounting bracket (not included) and plug your TV into the top power
output plate. Then plug your power cord set into the bottom power input plate. Complete installation by plugging
the male end of the power cord set into the nearby wall receptacle.
Page 2 of 3 11/05/2018
3026001 Page 3 of 3 11/05/2018
TEMPLATE
ACTUAL SIZE
TEMPLATE
ACTUAL SIZE
Questo manuale è adatto per i seguenti modelli
1
Indice
