Datalogic Gryphon GD4100 Manuale utente
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 1/10
BAR CODE (OPTION)
1. DEFINITION
The “Bar code” option enables to install a bar code reader on a second specific RS232
connector of the ATEQ instruments.
It enables on reading of the code to select a test program and eventually to launch the test of
control (if the option is validated).
The quantity of characters read by the reader should not exceed 22. Beyond the unit will not
take into account the character string (bar code string).
1.1. COMMUNICATION PARAMETERS CONFIGURATION
1.1.1. Bar code reader configuration
The Bar Code reader must be set with the following communication parameters:
9600 bauds,
7bits,
1stop,
Parity even.
The communication parameters of the ATEQ devices are the same by default and fixed, it's not
provide to change it.
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 2/10
1.1.2. RS232 port configuration
From the "CONFIGURATION" menu, select
the "AUTOMATISM" menu and then press the
button
By using the arrows, select
the "RS232" menu and validate with the
key.
By using the arrows, select
the "CODE READER" menu and validate with
the key.
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 3/10
2. BAR CODE READER CONFIGURATION
The bar code reader advised for a good functionning is the model
DATALOGIC Gryphon I GD4100 (USB).
For the reader configuration, follow this
process:
1) Enter in programming mode of the reader
by flashing this code (right hand)
"ENTER/EXIT PROGRAMMING MODE"..
2) Reset the reader to factory settings by
flashing this code (right hand)
"Factory Default Settings".
3) Program the reader by flashing the code
(right hand) "USB Keyboard
(with standard key encoding)".
4) Close the programming mode by flashing
the first bar code (below) "ENTER/EXIT
PROGRAMMING MODE".
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 4/10
3. FUNCTION ACTIVATION
Warning : at each parameter or configuration change will delete all the learnings. That will
necessary to learn all the codes for each program.
From the "CONFIGURATION" menu, select
the "AUTOMATISM" menu and then press the
button
By using the arrows, select
the "CODE READER" menu and validate with
the key.
By using the arrows, select
"Yes" and validate with the key.
The bar code reader menu is displayed.
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 5/10
By using the arrows, select
the "Pr. Select" menu select by "Yes" with the
arrows and validate with the
key.
The 'First Char." and "Char Number" are
displayed, By using the
arrows, select "First Char" and validate with
the key.
The parameter “First character” corresponds to the position of first character to take into
account in the total string of characters.
Then by using the arrows,
select "Char Number" and validate with the
key.
The parameter “Char Number” corresponds to the quantity of characters (or the length of the
chain) to take into account.
The sum of the two captured parameters must be lower or equal to the total quantity of
characters contained in the chain plus 1.
Parameters Total quantity of characters + 1 22
Example :
A
B C D E F G H I J K L M N O P Q R S T
U V
5
th
character
10 characters
Number total of characters = 22
In our example above, the program will be selected if the unit reads the character chain:
E F G H I J K L M N.
Note : if a same characters string is on several programs, the program with the smallest number
will be selected the others will be ignored.
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 6/10
"RESET EOC" parameter.
Adjusted on "No" the device will save in
memory the readed bar code for all the
following programs, until a new bar code will
be readed.
Adjusted on "Yes" it will must flash a new bar
code before each start cycle.
In the "KEYBOARD SUFFIX" parameter
check or enter the suffix value = 13.
This suffix will be applied at the end of the bar
code reader frame to notify to the device that
the frame is ended.
13 = CR in decimal (Carriage Return)
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 7/10
4. FUNCTION CONFIGURATION
Activate the function or check if it checked.
Press the key, the cursor slide to the
right hand.
By using the arrows, select
"Yes" and validate with the key.
The configuration menu appears.
The "NUM." parameter is the one that will
contain the readed bar code the the selected
program.
The "AUTO START" parameter will start the
program when the code is readed.
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 8/10
5. PARAMETER SETTING OF THE STRINGS (LEARNING)
The characters string learning will be done from the special cycles.
From the main menu, enter the special cycle
menu.
In the special cycle menu, select the special
cycle "CODE READER", and validate with
.
The device ask for the corresponding test
program to the characters strings which be
readed, and validate with .
The device confirms the special cycle
CODE READER. Press the "START CYCLE"
button.
Note :the device displays the current program
number that can be different than the one that
was selected for the bar code.
The device will wait for the bar code. The
corresponding program is displayed.
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 9/10
Then flash the code by using the bar code
reader. The captured characters are
displayed.
The code is recorded, the device is ready to
run. At each reading of this code, the device
will select the corresponding program.
To see the recorded code for one program, go
in the "FUNCTIONS/CODE READER" menu
of this programme.
If the flashed code is unknown, the message
"DEF. BAR CODE" is displayed.
Sheet # 694u – Bar code (option)
Version 1.04a User guide ATEQ 6th series Page 10/10
6. FRAMES
Examples of frames sended by the device, with the program bar code.
6.1. STANDARD MODE FRAMES
<01>:
<01>:13/10/201420:10:46
<01>:0.598bar:(OK):78Pa
<01>:123456789001XXXXXXXX01
<02>:
<02>:13/10/201420:10:57
<02>:0.597bar:(OK):85Pa
<02>:1234567890023333333301
<12>:
<12>:13/10/201420:11:06
<12>:0.597bar:(OK):85Pa
<12>:1234567890124444444412
6.2. EXPORT MODE FRAMES
→01→(OK)→88→Pa→0.597→bar→→123456789001XXXXXXXX01→13/10/2014→20:11:26
→02→(OK)→88→Pa→0.597→bar→→1234567890023333333301→13/10/2014→20:11:41
→12→(OK)→85→Pa→0.597→bar→→1234567890124444444412→13/10/2014→20:11:48
The " →" sign seams a tabulation.
Indice
Altri manuali Datalogic Lettore di schede
Datalogic
Datalogic Matrix 400 Manuale utente
Datalogic
Datalogic Matrix 210N Manuale utente
Datalogic
Datalogic Matrix 120 Manuale utente
Datalogic
Datalogic Gryphon D110 Manuale utente
Datalogic
Datalogic MATRIX-20 series Manuale utente
Datalogic
Datalogic OM-GRYPHON SERIES Manuale utente
Datalogic
Datalogic XRF410N Series Istruzioni per l'installazione e il funzionamento
Datalogic
Datalogic DLR-DK001-EU Manuale di installazione e funzionamento
Datalogic
Datalogic DLC6100 Series Manuale utente
Datalogic
Datalogic Touch 65 pro Manuale utente
