Datamax Perfomance Series Manuale utente
1 Media Hub Installation Guide
1 Safety
Warnings and Cautions
The following Warnings and Cautions are used throughout this manual:
Warning: Warnings alert you to possible safety risks.
Caution: Cautions alert you to the potential for equipment damage.
General Safety Information
Caution: This product is intended for indoor use only.
All service procedures should be done by properly trained and qualified service
personnel.
Any on-site assembly required during the installation process must be performed by
properly trained and qualified service personnel.
When operating, the product must be connected to a properly grounded and
appropriately rated AC receptacle using the supplied cord set.
Caution: This product contains sensitive electronic components that could be damaged
if exposed to excessive force.
Caution: Use only factory-approved consumables and cleaning kits. Use of any non-
approved supplies could damage the product and void the warranty.
Figure: 1 - 1 Caution - Hot
The printhead heats during printing. Do not touch.
3 USB Host Installation Guide
2 USB Host Installation Instructions
USB Host
Figure: 2 - 1 USB Host
2 | USB Host Installation Instructions
USB Host Installation Guide 4
Tools Needed
• 2.5mm Hex Head Wrench
• 3mm Hex Head Wrench
• 7mm Nut Driver
• #2 Phillips Screwdriver
• Long #2 Flat Blade Screwdriver
Safety Overview
Caution: ESD protection is required when performing these steps.
Warning: The cover set may only be removed by a Datamax-O’Neil Authorized Service
Center. Unauthorized service will void the manufacturer’s warranty.
Warning: The printer must be powered off and disconnected from utility power prior to
performing these procedures. Failure to heed this warning may result in personal injury
or damage to internal components.
• Maintain complete ESD protection in a safe, clean environment at all times while
servicing this equipment.
• When handling the printhead, grasp it by its edges.
• Avoid contact between the printhead and clothing.
• Never pull on any wires to disconnect connectors. This can void the manufac-
turer’s warranty.
USB Host Installation Instructions | 2
5 USB Host Installation Guide
USB Host Installation Procedure
Note: Retain all hardware for reassembly.
1. Open the media cover assembly.
2. If the present sensor option is installed on the cover, gently pry the sides of the
cable chain outward to disconnect it from the present sensor cable connection
cover.
Note: If there is no present sensor mounted on the media cover, continue to step 5.
Figure: 2 - 2 Cable Chain Disconnect
Note: To clarify the illustration above, the cable chain is shown disconnected from the
printer chassis backbone.
2 | USB Host Installation Instructions
USB Host Installation Guide 6
3. Remove all four 7mm nuts securing the present sensor cable connection cover to
the media cover.
Figure: 2 - 3 PCB Cover
4. Disconnect the present sensor cable connector and route the connector (male) out
of the opening.
5. Loosen all three (3) 2.5mm hex head screws from the upper cover mount.
Note: For an easier re-installation, loosen but do not remove the screws.
Figure: 2 - 4 Upper Screws
USB Host Installation Instructions | 2
7 USB Host Installation Guide
6. Loosen and remove the three (3) 2.5mm hex head screws securing the right side
cover to the printer chassis.
Figure: 2 - 5 Right Side Screws
7. Lift and remove the cover assembly from the printer chassis.
Caution: Exercise caution when removing the cover set assembly and secure it in a safe
position where it will not be damaged.
Figure: 2 - 6 Lift Cover Assembly
2 | USB Host Installation Instructions
USB Host Installation Guide 8
8. If applicable, loosen and remove the power ribbon transport assembly screw and
cover.
Figure: 2 - 7 Power Ribbon Transport Assembly Cover
USB Host Installation Instructions | 2
9 USB Host Installation Guide
9. Gently push the upper panel locking tab upward enough to begin to separate the
top of the panel from the printer frame.
Figure: 2 - 8 Front Panel Removal
Caution: Be careful not to damage any surrounding components.
10.While holding the upper part of the panel, gently push the lower panel locking tab
downward enough to separate the panel from the printer frame.
Caution: Be careful not to damage any surrounding components.
Upper Tab
Lower Tab
Indice
Altri manuali Datamax Etichettatrice
Datamax
Datamax RP Series Manuale utente
Datamax
Datamax M-Class Mark II Manuale utente
Datamax
Datamax M-Class Mark II Manuale utente
Datamax
Datamax M-Class Mark II Manuale utente
Datamax
Datamax I-Class Manuale utente
Datamax
Datamax H-Class Manuale utente
Datamax
Datamax Workstation w1110 Manuale utente
Datamax
Datamax A-Class Mark II Manuale utente
Datamax
Datamax M-Class Mark II Manuale utente
Datamax
Datamax MICROFLASH 4T Manuale utente
Datamax
Datamax A-Class A-4212 Manuale utente
Datamax
Datamax Prodigy Plus Manuale utente
Datamax
Datamax E-class E-3202 Manuale operativo e di manutenzione
Datamax
Datamax E-Class Mark III Professional+ Manuale utente
Datamax
Datamax RL3 Manuale utente
Datamax
Datamax E-Class Mark III Manuale utente
Datamax
Datamax E-4304 Manuale utente
Datamax
Datamax H-Class Manuale utente
Datamax
Datamax I-Class Mark II Manuale utente
Datamax
Datamax M-Class Mark II Manuale utente
