DaVinci Hypermax OXYGEN Manuale utente
SET-UP
Instruction
MANUAL
QUICK START
set up & usage videos
(aim camera at this image to begin)
WARNING ⚠
DO NOT USE SYSTEM IF YOU HAVE
COPD and/or severe COPD
with CO2 retention.
(1) PVC Frame Top
(1) PVC Frame Bottom with
Base Plate & Hose Elbow
(4) PVC Long Frame Poles
(Separate Box)
(4) 1 lb Weights (Attached
to Frame Top) - Optional
(1) 900 Liter Oxygen Bag/Cylinder
(1) Red Capped Relief Valve
(Peep Valve)
(1) Mask & Strap
(1) Thin ¼” Supply Hose
(Concentrator to Cylinder)
(1) 10’ Breathing Hose
(Cylinder to Mask)
(1) Green Breathing Valve
(1) Inline Back Flow Valve
(1) Velcro Hose Holder
(1) Flexible “Gooseneck”
Long Arm Clip
PACKAGE CONTENTS
© 2022 HyperMax Oxygen
Congratulations on receiving your HyperMax
Oxygen System — atrue scientific breakthrough for
improving your health, immunity, endurance and
longevity. We created the HyperMax Oxygen
Wellness System to help people like you restore
and increase their body’s oxygen levels and greatly
improve their overall Health, Fitness and Well-Being.
This instruction manual will help you set up your
unit smoothly and easily, from start to finish, and
you’ll be on your way to 93% oxygen in no time.
davincimedicalusa.com
4
STEP
ONE
1
OXYGEN
CONCENTRATOR
davincimedicalusa.com
5
Start by unpacking the HyperMax Oxygen concentrator that was shipped to
you in a large and heavy box. First lay the box on its side, and carefully slide
the Oxygen concentrator unit out from the shipping container.
Then stand the HyperMax Oxygen concentrator back in its upright position.
CONTROL PANEL
CONTROL PANEL
davincimedicalusa.com
6
1. Select a location that allows the concentrator unit to draw in room air
without being restricted. Make sure that the unit is at least 4 inches
(10cm) away from any wall, furniture, or curtains that could impede
adequate airflow. Do not place the unit near any heat source.
2. Plug the power cord into an electrical outlet.
3. Connect the provided silicon tubing to port at top right rear of the
machine as shown in Image 1.
4. Press the power switch to the ON [I] position. The LED display screen will
illuminate.
5. Press the ON/OFF power button once to turn the unit on. The oxygen will
begin flowing from the unit immediately.
6. Adjust the flow by turning the knob on the top of the flow meter until the
ball is centered at 10. See Image 3 for knob reference.
7. When the oxygen concentrator is not in use, press the power switch to
the OFF [O] position.
Image 1 Image 2 Image 3
•Continuous Working Mode - By pressing the ON/OFF button, oxygen
will begin to flow from the oxygen concentrator, using a "continuous"
working state (will stay on until you manually turn it off). The LCD screen
will display the total usage time your generator has been used (like a car
odometer).
•Timer Working Mode - Once the oxygen has begun flowing, press the
"timing+" button - this will allow the unit to begin in the timed working
mode. Each time the "timing+" button is pressed, the preset time will be
increased by 10 minutes. The maximum preset time is 480 minutes. By
pressing the "timing-" button, the preset time will decrease, in
increments of 10 minutes.
davincimedicalusa.com
7
MODE OPTIONS
(Continuous and Timer)
The Da Vinci 10 LPM Oxygen Concentrator has two different mode options
available:
1. Set the oxygen timer for 90 minutes for the first time to completely fill
the bag.
2. If the bag is half full after your session, you will only need to set the
oxygen timer for 40 minutes to fill the bag.
3. To double or triple the speed at which your bag is filled, you would
simply add a second or third generator.
4. You may leave the oxygen generator running during your exercise
sessions.
davincimedicalusa.com
8
BAG FILLING TIPS
Next, set up the HyperMax frame located in the other large box you received.
After opening this box, take your mask out and set it to the side. Then remove
the entire HyperMax frame from the box as one unit. Once your frame is out
of the box, separate the top of the frame from the short colored poles used
for shipping, and then set this top frame to the side.
FRAME
SET-UP
STEP
TWO
2
davincimedicalusa.com
9
Locate the long, thin shipping tube you received from HyperMax. This
long tube contains the four poles you will need to complete the set up of
your HyperMax frame.
One at a time, you want to remove the short colored poles and set them
aside. These small poles are temporary and designed for shipping — but
the long black poles are used for the actual HyperMax frame.
Start by inserting each long pole, one at a time, into each hole at the base
of the frame. It’s important to make sure that you get all four rings on a side
of the Oxygen Bag/Cylinder onto a pole, and then repeat this step three more
times. Once you have all four poles in the frame bottom, with all four rings on
each pole, you will then push each pole down firmly into its proper fitting.
These poles will connect the bottom to the top of the frame.
FRAME
SET-UP
(CONT’D)
STEP
THREE
3
davincimedicalusa.com
10
Indice
Altri manuali DaVinci Attrezzature mediche
