DAVIS Solar Power Kit Manuale utente

Product#6610

OLAR

OWER

FOR

IRELESS

ANTAGE

NSTALLATION

ANUAL

The Solar Power Kit (#6610) provides power to a Wireless Vantage Pro console

when mounted in a remote location or in a ﬁeld station. The kit consists of

three key elements – a solar panel, a 6-Volt battery, and a regulator circuit –

mounted in a protective housing:

Note:

Use Solar Power Kit #7707 with Cabled Vantage Pro consoles.

Components

The Solar Power Kit includes the following components and hardware:

Tools for Setup

✦

Adjustable wrench or 7/16” wrench

✦

Drill and 3/16” (5 mm) drill bit (if mounting on a vertical surface)

Location Tips

The following tips should help you ﬁnd the best possible location and position

for your Solar Power Kit.

✦

The panel should be mounted facing South in the Northern Hemisphere

and North in the Southern Hemisphere.

✦

Position the solar panel to have maximum exposure to the sun

The solar

panel works best when the surface of the panel receives full sunlight.

Mount the panel away from fences, buildings, trees or other equipment

or obstructions that may cast a shadow over the panel.

1/4" Flat Washers

1/4" Lock Washers

1/4" Hex Nuts

U-Bolts

1/4" x 1-1/2" Lag Screws Shelter

Power Cable

4" Cable Tie

8" Cable Ties

Page2 SolarPowerKitforWirelessVantagePro

Securing the Power Cable

Secure the power cable to prepare the Solar Power Kit for installation.

1. Determine how much of

the 20’ (6 m) power cable is

needed to reach your Wire-

less Vantage Pro console.

2. Pull that length of cable

through the rubber grom-

met located in the bottom

of the shelter.

3. Secure the cable inside the

shelter with a 4” Cable Tie

fastened to the cable tie

mount.

The cable tie provides

strain relief for the power

cable.

Mounting the Solar Power Kit on a Pole

The U-bolts included with the Solar Power Kit ﬁt poles from 3/4” to 1 1/4”

(19mm to 31mm) in diameter.

1. While holding the shel-

ter against the pole, place

a U-bolt around the pole

and through the two

holes at the top of the

shelter.

2. Place a ﬂat washer, a lock

washer and a hex nut on

each of the bolt ends.

3. Tighten the nuts using an

adjustable wrench or 7/

16” wrench, .

4. Place the second U-bolt

around the pole and

through the two holes at the bottom of the shelter.

Put a ﬂat washer, a lock washer, and a hex nut on each bolt end, and

tighten the hex nuts.

Power Cable

Battery

Secure Cable

Using

Cable Tie Mount

Grommet

Securing the Power Cable

Flat

Washer

Lock

Washer

Hex

Nut

U-Bolt

Mounting Solar Power Kit on a Pole

MountingtheSolarPowerKitonaPost Page3

Mounting the Solar Power Kit on a Post

1. With a 3/16” (5 mm) drill bit, drill two holes approximately 2" (50 mm)

apart. Use a carpenter’s level to ensure the holes will be level.

2. Drill two more holes 7-1/32”

below the upper holes.

3. Insert the 1/4” x 1-1/2” lag

screws through the ﬂat wash-

ers, and through the holes at

the top of the shelter into the

post.

Using an adjustable wrench

or 7/16” wrench, tighten the

lag screws.

4. Insert the 1/4” x 1-1/2” lag

screws through the ﬂat wash-

ers, and through the holes at

the bottom of the shelter into the post.

Using an adjustable wrench or 7/16” wrench, tighten the lag screws.

Connecting Power to the Vantage Pro Console

1. The Solar Power Kit’s connector plugs directly into the power jack located

on the bottom of the Vantage Pro Console. See your Vantage Pro Console

Manual for details.

2. Secure the power cable run using the included 8” cable ties.

Troubleshooting

While the Solar Power Kit is designed to provide years of trouble-free opera-

tion, occasional problems may arise. If you experience a problem, please check

the troubleshooting tips below before calling technical support.

✦

Solar panel fails to power station and battery is over 5 years old

As the battery ages, it will lose capacity and may completely discharge.

If this is the case, simply replace the battery.

CAUTION:

Do not incinerate the used battery; it may burst. Arrange for proper recycling in your

locality.

✦

Solar panel fails to power station and battery is less than 5 years old

If the solar kit fails to power the station, try the following:

1. Make sure the panel is not being shaded from the sun.

2. Open the solar panel shelter and check that the wire connections

are secure and that battery is free from corrosion and excessive

deposits on the terminal.

Flat

Washer

Lag

Screw

Mounting Solar Power Kit on a Post

Product Numbers: 6610

Davis Instruments Part Number: 7395.306

Solar Power Kit for Wireless Vantage Pro

Rev A. Manual (7/27/01)

This product complies with the essential protection requirements of the EC EMC Directive 89/336/EC.

3465 Diablo Avenue, Hayward, CA 94545-2778

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected] • www.davisnet.com

3. Clean the solar panel using a water spray, or a soft cloth and

soapy water followed by a clean water rinse.

4. Check the battery’s voltage with a voltmeter; the battery must

have at least 5.5 V to power the station. More than 6 V indicates

an adequately-charged battery.

5. Try exposing the kit (with console unplugged) to ample sunlight

for a week, or, use a charger designed to recharge a 6 V gel cell

battery. If you are unable to charge the battery above 6 V, replace

the battery.

If, after checking this troubleshooting guide you are unable to solve the prob-

lem, please call our technical support team at (510) 732-7814 for assistance

(M-F, 7 am–5:30 pm PST).

Note:

Please do not return your unit for repair without prior authorization.

Speciﬁcations

Operating Temperature. .. .. .. .. .. .. .. .. . .. .. .. .. .. –4° to120° F(–20° to50° C)

Non-operating Temperature .. .. .. .. . .. .. .. .. .. .. .. . –50°to 158°F (–45°to 70° C)

Battery .. .. .. .. .. .. . .. .. .. .. .. .. .. .. .. .. . .. .. . 6Volt 1.3Amp HourLead-Acid

(PowersonicPS-612 orequivalent)

Solar Panel . . .. .. .. .. .. .. .. . .. .. .. .. .. .. .. .. .. . 0.5watts

Power CableLength .. .. .. .. .. .. .. .. .. .. . .. .. .. .. . 20’(6 m)

Dimensions . . .. .. .. .. .. .. .. . .. .. .. .. .. .. .. .. .. . 6.25” x2.25” x7.88” (158x 57x 200mm)

Weight . . .. .. .. .. .. .. .. .. . .. .. .. .. .. .. .. .. .. .. 1 lb. 13.50oz. (.836kg)

Altri manuali per Solar Power Kit

Questo manuale è adatto per i seguenti modelli

Altri manuali DAVIS Accessori

DAVIS

DAVIS Short-Range Modem Pair Manuale utente

DAVIS

DAVIS Vantage Pro2 Updater Manuale utente

DAVIS

DAVIS 7817 Manuale utente

DAVIS

DAVIS 6440 Manuale utente

DAVIS

DAVIS 7714 Radiation Shield Manuale utente

DAVIS

DAVIS Solar Power Kit Manuale utente

DAVIS

DAVIS Soil Moisture Sensor & Temperature Probe Manuale utente

DAVIS

DAVIS WeatherLink Live 6100 Manuale utente

DAVIS

DAVIS UV Sensor Manuale utente

DAVIS

DAVIS Surge Protector Shelter (Small) Manuale utente

DAVIS

DAVIS 7709 Solar Power kit Manuale utente

DAVIS

DAVIS Vantage Pro2 Updater Manuale utente

DAVIS

DAVIS AirLink 7210 Manuale utente

DAVIS

DAVIS 6151 Manuale utente

DAVIS

DAVIS 6440 Manuale utente

DAVIS

DAVIS AirLink Manuale utente

DAVIS

DAVIS SONIC-ANEMO-DZP Manuale utente

DAVIS

DAVIS ISS Guida

DAVIS

DAVIS Vantage Pro ISS Retrofit Kit Manuale utente

DAVIS

DAVIS Wireless Temperature/Humidity Station Manuale utente

DAVIS

DAVIS Vantage Pro2 Updater Manuale utente

DAVIS

DAVIS and Vantage Pro Manuale utente

DAVIS

DAVIS 6322C Manuale utente

DAVIS

DAVIS Solar Radiation Sensor Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente