Daytona B917 Manuale utente
1
B917 WHEEL BALANCER
READ THIS ENTIRE MANUAL BEFORE OPERATION BEGINS
Serial No. __________
Model No. ___B 917___
2
Warning
⚫This manual is a necessary part of the product. Please read carefully.
⚫Keep the manual for later use when maintaining the machine.
⚫This machine can only be used for the designated purposes. Never use it for any other purpose.
⚫The manufacturer is not responsible for the damage incurred by improper use or use other than the intended
purpose.
Precaution
⚫The equipment can only be operated by qualified personnel with special training. Modification to any
components or parts, or use the machine for other purpose without either obtaining the agreement from the producer,
or observing the requirement of the instructions may lead to direct or indirect damage to the equipment.
★ The equipment should be installed on the stable ground, not wooden pallet, otherwise not accurate.
⚫Keep the back panel 0.6M away from the wall for good ventilation. Enough room should be left on both
sides for convenient operation.
⚫Do not put the equipment a place with high temperature or moisture, or near the heating system, water tap,
air-humidifier or chimney.
⚫Avoid lots of dust, ammonia, alcohol, thinner or spraying binder.
⚫People who are no operating the machines should be kept away when it is used.
⚫Use appropriate equipment and tools, protective and safety equipment, including eyeglasses, earplugs and
working boots.
⚫Pay special attention to the marks on the machine.
⚫Do not touch or approach the moving parts by hand during operating.
⚫Do not remove the safety device or keep it from working properly.
3
Contents
1. General-----------------------------------------------------------------------------------------------------------------1
2. Machine assembly----------------------------------------------------------------------------------------------------1
3. Controls and components--------------------------------------------------------------------------------------------3
4. Indication and use of wheel balancer------------------------------------------------------------------------------6
5. Self-calibration of wheel balancer -----------------------------------------------------------------------------10
6. Errors------------------------------------------------------------------------------------------------------------------11
7. Self- diagnoses-------------------------------------------------------------------------------------------------------12
8. Setting machine------------------------------------------------------------------------------------------------------12
9. OPT function --------------------------------------------------------------------------------------------------------13
10. Spare parts list and Exploded drawings-------------------------------------------------------------------------15
4
1. General
1.1. Technical data：
⚫Max wheel weight：65kg
⚫Power：0.2kw;0.37kw
⚫Power supply: 220v;230v;240v;110v;50hz;60hz
⚫Balancing accuracy：
1g
⚫8balancing modes: DYN, ALU1, ALU2, ALU3, ALU4, ALU5, ALUS, ST
⚫Balancing speed：200r/min
⚫Cycle time：8s
⚫Rim diameter：10〃～24〃(256mm～610mm)
⚫Sound pressure level during work cycle：<70db
1.2. Features：
⚫ALU balancing mode may choose 9 o’clock or 12 o’clock position to add weight
⚫Statistic and dynamic balancing, ALU-programs for alloy rims or special shaped
⚫Self diagnoses, easy to find the problem
⚫Apply to steel and aluminum alloy rim
1.3. Working environment：
⚫Temperature：5～50℃
⚫Height：≤4000m
2．Machine assembly
2.1. Unpack
Unpack the carton, check if missing any spare parts.
No.
Item
Qty
1
Width gauge
1
2
Conic No.1
1
Conic No.2
1
Conic No.3
1
Conic No.4
1
3
Quick relase nut
1
4
Thread hub
1
5
Bowl for quick nut
1
6
Pad for bowl
1
7
Balancing hammer
1
8
100g weight
1
9
Allen wrench
1
5
2.2. Install
⚫The equipment should be installed on the stable ground, not wooden pallet, otherwise not accurate.
⚫Keep the back panel 0.6M away from the wall for good ventilation. Enough room should be left on both
sides for convenient operation.
2.3. Fix balancer to floor with screws on the bottom.
2.4. Install adaptor
The wheel balancer is supplied complete with cone type adaptor for fastening wheel with central bore. (see below
picture)
2.5. Install wheel
Clean wheel, take off counterweights, check pressure of wheel.
Choose the way of installation according to the type of wheel.
Main shaft-wheel— Main shaft-suitable cone(big head towards inside)
suitable cone( small head towards inside)—quick handle nut —wheel—quick handle nut
Attention：May add a wheel, and hold the wheel to help install the thread hub. When installing or taking off wheel,
do not let wheel move on the shaft, to avoid scratching shaft.
3．Controls and components
No.
Item
Standard/Optiona
l
6
A
Switch
S
B
Head with
tool tray
S
C
Gauge head
S
D
Main shaft
S
E
Pedal
breaker
O
F
Safe guard
S
G
Key board
S
Six balancing modes
Icon
Balancing
mode
Operation
Add weights
Standard/Default
Turn on machine
Input a,b,d value
Start spin, after spin stop
Clip on weights on
both sides of rim edge
ALU2
1. Turn on machine
2. Input a,b,d value
3. Press ALU button, indicator lit up
4. Start spin, after spin stop
Add adhesive weights
on the rim shoulder
both sides
(Button Colors May vary)
7
ALU3
1. Turn on machine
2. Input a,b,d value
3. Press ALU button, indicator lit up
4. Start spin, after spin stop
Clip on weight on
inside rim edge, add
adhesive weight on
outside rim shoulder
ALU1
1. Turn on machine
2．Input a,b,d value
3．Press ALU button, indicator lit up
4．Start spin, after spin stop
Add adhesive weights
on the rim shoulder
both sides
ALUS
1. Turn on machine
2. Press ALU button, indicator lit up
3. Input aI,aE,d value
4. Start spin, after spin stop
Add adhesive weights
on the two positions
gauge head touch
Static mode, for
motorcycle
wheels
1. Turn on machine
2. Input a,b,d value
3. Press ALU button
Start spin, after spin stop
Add adhesive weight
Key board (H)
Icon
Function
Icon
Function
Set distance
Optimization of unbalance
Set rim width
Selection of “ALU” modes
Set rim diameter
Static mode, for motorcycle wheels
“ST” Will show in right display
Recalculation
Unbalance display pitch and threshold
Start
Stop/Cancel
8
4. Indication and use of wheel balancer
4.1．DYN (Standard/Default) mode
4.1.1. Clean wheel, take off counterweights, check pressure of wheel.Choose the way of installation according to the type
of wheel.
Main shaft-wheel— Main shaft-suitable cone(big head towards inside)
suitable cone( small head towards inside)—quick handle nut —wheel—quick handle nut
Attention：May add a wheel, and hold the wheel to help install the thread hub. When installing or taking off wheel,
do not let wheel move on the shaft, to avoid scratching shaft.
4.1.2. Turn on machine
4.1.3. Input a b d value
ab
d
◼Move gauge to touch edge of rim (Fig.1), read the value of distance, press and to change，set “a”
value.
◼Use width gauge to read the value of width (Fig. 2), press and to change, set “b” value.
◼Read the value of diameter (marked on the wheel), press and set “d” value.
Fig.1 Fig.2
9
4.1.4. Put down the guard and; press to perform a measuring spin.
4.1.5. In a few seconds the wheel is brought to operating speed and begin measuring unbalance, the unbalance values
remain on instruments 1 and 3 when the wheel stopped. Press may check the real unbalance value under threshold.
4.1.6. Anticlockwise moving wheel slowly, the displays with right LED’s lit up full indicate the correct angular position
where to mount the counterweights (12 o’clock position) outside, as Fig.3, clip the counterweight.
Fig. 3
4.1.7．Anticlockwise moving wheel slowly, the displays with left LED’s lit up full indicate the correct angular position
where to mount the counterweights (12 o’clock position) inside, as Fig.4, clip the counterweight.
Fig. 4
4.1.8． After finishing cliping the counterweights, put down the guard or press ，to perform balancing spin
again, if comes out 00 00，means balancing succeed. (Fig.5)
Fig. 5
4.2．ALU-2 mode (ALU-1, ALU3 same operation, only the position to add weights
different)
4.2.1. Set “a” “d” “b” values
10
4.2.2. Press until ALU2 indicator lit up
4.2.3. Put down the guard or press to perform a measuring spin.
4.2.4. In a few seconds the wheel is brought to operating speed and begin measuring unbalance, the unbalance values
remain on instruments 1 and 3 when the wheel stopped. Press may check the real unbalance value under threshold.
4.2.5. Anticlockwise moving wheel slowly, the displays with right LED’s lit up full indicate the correct angular position
where to mount the counterweights, 12 o’clock position (9H=Off) or 9 o’clock (9H=On) position outside, as Fig.6, add
the counterweight.
Fig. 6
4.2.6. Anticlockwise moving wheel slowly, the displays with left LED’s lit up full indicate the correct angular position
where to mount the counterweights, 12 o’clock position (9H=Off) or 9 o’clock (9H=On) position inside, as Fig.7, add the
counterweight.
Fig. 7
4.2.7. After finishing mounting the counterweights, put down the guard or press ，to perform balancing spin again,
if comes out 00 00，means balancing succeed. (Fig.8)
Fig. 8
4.3．ALU－S mode
This mode is used for special rim, if ALU1/ALU2/ALU3 can not be used, you should choose ALUS mode.
4.3.1. Turn on machine, press until the indicator of ALUS lit up.
Indice
