DaytonAudio DTA-100ST Manuale utente

100W DESKTOP

STEREO AMPLIFIER

WITH BLUETOOTH 5.0

Model: DTA-100ST

User Manual

Safety Information

To reduce the risk of electric shock, do not

remove cover. No user serviceable parts inside.

Refer servicing to qualied personnel. To reduce

the risk of re and shock do not expose unit to

rain or moisture. The unit should be connected

to an earth grounded AC electrical socket. The

unit should be operated in a well ventilated

area. Minimum clearance is 2 inches from the

ventilation openings.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(a) This device may not cause harmful interference.

(b) This device must accept any interference received, including interference that

may cause undesired operation.

IMPORTANT SAFETY INSTRUCTIONS

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Changes or modications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

Thank you for purchasing the Dayton Audio DTA-100ST Desktop Stereo Amplier. The

compact design is perfect for focused application where space is at a premium. With 100

watts of real power it has never been easier to power almost any speaker.

Contents

Features............................................................................................................................ 3

Package Contents ........................................................................................................... 3

Controls and Functions

Front Panel................................................................................................................. 4

Rear Panel ................................................................................................................. 5

Connecting Speakers ..................................................................................................... 6

Operation

Bluetooth Operation ................................................................................................... 6

Auto On ...................................................................................................................... 6

Installing Mounting Brackets......................................................................................... 7

Specications .................................................................................................................. 7

Warranty ........................................................................................................................... 8

Features

• Compact desktop size, perfect for a big sound from a small package

• Built-in Bluetooth receiver for streaming audio from anywhere in the room

• Stereo preamp out makes it incredibly simple to add a subwoofer amplier for

ultimate enjoyment

• Auto-on function keeps your equipment safe and saves power when not in use

• Built-in power supply with automatic 110/220V input voltage switching

Package Contents

• DTA-100ST Desktop Stereo Amplier

• Mounting Brackets (pair)

• AC Power Cord

• User Manual

*Please contact Dayton Audio to make sure that nothing is missing from the package

Front Panel

Controls and Functions

1. Power/Standby Button

This button will turn the amplier on and place it into standby. The indicator light

will illuminate white when the amplier is on. It will illuminate red when the amp

is in standby.

2. Source Selection Button

Use this to toggle between the Aux and Bluetooth inputs. The corresponding light

will illuminate white when the input is active. While the Bluetooth input is active,

press and hold to disconnect the device and enter pairing mode. Press and hold

the button while in pairing mode to revert to the previously connected device.

3. Volume Control

Live a little and turn the volume up. After all, that’s what the DTA-100ST is for.

The volume knob controls the volume of SPEAKER OUTPUT and the PRE OUT

connections.

DTA-100ST

AUX BT

VOLUME

Rear Panel

1. BLUETOOTH ANTENNA

2. AUTO ON CONTROL

This is a handy feature when using the DTA-100ST in conjunction with other

audio equipment.

It will safely turn off the amp when audio stops and will turn it back on when audio

is detected. (please see pg. 6 for a more detailed explanation)

3. LINE INPUT (AUX)

4. PRE OUT

Stereo RCA jacks allow for connecting the DTA-100ST to other audio equipment.

This signal level is controlled by the volume knob and will output whatever input

is selected. It is not affected by the High Pass Filter (HPF).

5. HIGH PASS FILTER

This will help remove low frequencies from the connected speakers to protect

from high-excursion. This feature is also particularly handy when using an external

subwoofer so that the main speaker and subwoofer outputs do not affect each other.

6. SPEAKER OUTPUT

Using insulated 2 conductor wire to connect to speakers. The polarity, positive

(+), and negative (-) for all speaker and amplier connections must be consistent

so both the left and right speakers are in phase.

NOTE: The speaker outputs are not bridgeable.

7. AC POWER INPUT

The DTA-100ST is capable of operation in 110V and 220V regions. The internal

power supply will automatically sense the power input and operate appropriately.

8. MAIN POWER SWITCH

Turns the device on and off.

Amplifier,Model NO.:DTA-100ST 100-240V~

50Hz/60Hz 100W

Connecting Speakers

The amplier can power speakers with a minimum impedance of 4Ω, using speakers with

a lower impedance can cause damage to the amplier. Use high quality two conductor

speaker wire and your choice of connector to connect your speakers to the binding posts

on the rear of the unit.

Connect the DTA-100ST’s left speaker terminals marked “L-” and “L+” to the corresponding

“-” and “+” terminals on your left speaker. Repeat the same process for the right channel.

NOTE:Never connect the negative terminals together or to ground. The DTA-100ST is not

designed to operate in a bridged mode and attempting to do so may damage the amplier.

Operation

Bluetooth Operation

When switching to the Bluetooth input, the indicator light will ash to indicate that the device

is ready to pair. If the last connected device is within range it will connect automatically.

Otherwise, look for the DTA-100ST in your device’s setup menu and initiate pairing.

The DTA-100ST will automatically disconnect after 15 minutes of silence and

enter standby.

AUTO ON Function

For ultimate control in any installation, the DTA-100ST has an auto sensing function that

can turn off the amplier when not in use and turn it back on when audio is detected.

When the DTA-100ST is in standby the power indicator will illuminate red. To activate this

function, toggle the AUTO ON switch. Otherwise, leave the switch in the ON position for

normal operation.

When using the AUX input, the DTA-100ST will enter standby after fteen minutes of

silence. The amplier will turn back on when music is played again. The power light will

change to white and the AUX input light will light up again. The DTA-100ST will remain in

standby until audio is sensed on the line inputs, or the front panel controls are used.

While using the Bluetooth input the DTA-100ST will unpair from the connected device after

fteen minutes of silence and enter standby. The power light will illuminate red and the

Bluetooth light will ash to indicate that pairing mode is active. The DTA-100ST will remain

in pairing mode until a Bluetooth device connects or the front panel controls are used.

Amplifier,Model NO.:DTA-100ST 100-240V~

50Hz/60Hz 100W

Installing Mounting Brackets

The DTA-100ST can be conveniently mounted on or underneath a shelf or desk

with the included mounting brackets. The brackets can be attached to the sides of

the amplier by removing the screws and replacing them with the brackets in plac

Specications

Maximum Power Output (Peak).............. 100W/CH @ 4Ω

RMS Power Output.................................. 45W/CH @ 4Ω

Total Gain .................................................27.5 dB

THD+N ......................................................<0.06% at rated power output

Frequency Response .............................. 25 Hz – 20,000 Hz

Input Sensitivity....................................... 215 mV

Channel Separation................................. 70 dB

Minimum Speaker Impedance................ 4Ω

Signal to Noise Ratio............................... 101 dB

Bluetooth..................................................5.0

General

Power Requirement................................. 100-240V, 50/60 Hz

Standby Power Consumption ................ 2W

Amplication............................................Class D

Dimensions (W, H, D) .............................. 7.5 x 2 x 5.5 in. (190 x 50 x 139 mm)

Weight.......................................................2.78 lbs. (1.26 kg)

All Specications are accurate at the time of printing.

Dayton audio reserved the right to make improvements without notice.

IMPORTANT! DO NOT BLOCK VENTS!

DTA-100ST

Shelf

Dayton Audio®Last Revised: 2/28/2023

daytonaudio.com

tel + 937.743.8248

info@daytonaudio.com

705 Pleasant Valley Dr.

Springboro, OH 45066

USA

Warranty

Dayton Audio products are warranted to be free of all defects in material and workmanship for 5

YEARS from the date of purchase from an authorized Dayton Audio dealer. This warranty and all

rights provided are limited to the original owner and are non-transferable. Responsibility is limited

to replacement or repair as set forth in this warranty statement.

Should a product require warranty service during this period, Dayton Audio will repair or replace

without charge, any part or product proving defective in material or workmanship. All warranty

repairs and service must be performed by an authorized Dayton Audio technician or service

facility. The use of non-authorized repair services renders this warranty null and void, and any

charges relating to non-authorized repair are the responsibility of the product owner.

All expenses (except return shipping costs) related to replacing or repairing a defective part or

product under this warranty shall be assumed by Dayton Audio. Dayton Audio reserves the right

to replace defective product with a new or factory reconditioned unit.

For more information and to register your new Dayton Audio device visit daytonaudio.com.

Indice

Altri manuali DaytonAudio Amplificatore

DaytonAudio

DaytonAudio DA10T Manuale utente

DaytonAudio

DaytonAudio DTA-120BT Manuale utente

DaytonAudio

DaytonAudio PMA800DSP Manuale utente

DaytonAudio

DaytonAudio SBA302-BT Manuale utente

DaytonAudio

DaytonAudio DSPB Series Manuale utente

DaytonAudio

DaytonAudio SPA500 Manuale utente

DaytonAudio

DaytonAudio MA1260 Manuale utente

DaytonAudio

DaytonAudio APA1200DSP Manuale utente

DaytonAudio

DaytonAudio WF60PA Manuale utente

DaytonAudio

DaytonAudio SPA250 Manuale utente

DaytonAudio

DaytonAudio KAB-2150 Manuale utente

DaytonAudio

DaytonAudio DTA-PRO Manuale utente

DaytonAudio

DaytonAudio HTA50BT Manuale utente

DaytonAudio

DaytonAudio SPA1200DSP Manuale utente

DaytonAudio

DaytonAudio DTA3116S Manuale utente

DaytonAudio

DaytonAudio WB40A Manuale utente

DaytonAudio

DaytonAudio HTA200 Manuale utente

DaytonAudio

DaytonAudio HTA200BT Manuale utente

DaytonAudio

DaytonAudio MA1240A Manuale utente

DaytonAudio

DaytonAudio DTA-2 Manuale utente

DaytonAudio

DaytonAudio SA240 Manuale utente

DaytonAudio

DaytonAudio APA150 Manuale utente

DaytonAudio

DaytonAudio WF40A Manuale utente

DaytonAudio

DaytonAudio HTA100BT Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente