DB MA-350.1D Manuale utente

OWNER’S MANUAL РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ CAR AMPLIFIERS

MONO AMPLIFIER CLASS D

http://deafbonce.com

MA-350.1D MA-450.1D MA-800.1D MA-1500.1D MA-2000.1D

CONTENTS EN

1. Introduction

2. Safety instructions

3. Typical installation sequence

4. Connection methods

5. Wiring diagrams

6. Selection of the diameter of power cables and speaker cables

7. Speciﬁcations

8. Possible faults and their solutions

9. Box contents

10. Warranty and maintenance info

11. Information on disposal of the electrical and electronic equipment (for the European countries with

separate waste collection)

Thank you for purchasing this Deaf Bonce product of Machete series! Our company is committed to the creation of extremely

high-proﬁle systems with no loss of quality.

To ensure proper use, please carefully read through this manual before using this product. It is especially important that you

read and observe caution’s in this manual. Please keep the manual in a safe and accessible place for future reference.

1. Make sure that your vehicle has a 12V DC electrical system with negative grounding. Before installing the ampliﬁer in cars,

trucks or buses, check the battery voltage.

2. Check the state of on-board power supply of your vehicle, the battery and the alternator. When the engine is running,

depending on the ambient temperature, the voltage to be outputted by the alternator must be within the range of 14 to 14.7 V.

Open circuit voltage (OCV) of the battery must be within the range of 12.5 to 13 V. Make sure that the rated current of the

alternator and the battery capacity is enough to provide increased consumption.

For example, for the power of the ampliﬁer 1000 W, the rated current of the alternator is required at the rate of 1000 W / 13 V

= 77 amperes. A more powerful ampliﬁer requires a more powerful alternator as well as an additional battery.

3. Do not place the ampliﬁer in the engine compartment and also in the places exposed to water, moisture, dust or dirt.

4. Never stretch the cables outside of the car and near the moving parts of the car. This can lead to destruction of the

insulating layer, short circuit and ﬁre.

5. The ampliﬁer should be installed in areas of the car where the temperature varies from 0 °C (32 °F) to 55 °C (131 °F). The

ampliﬁer should be in a place with a good air circulation. The horizontal position of the ampliﬁer is the best way to install.

6. During the operation the ampliﬁer may be heated up to 80 °C (176 °F). Before you touch it, make sure it is not overheated

that may be dangerous.

7. To improve the cooling of the ampliﬁer, it is recommended to clean periodically the heatsink from dust. When cleaning the

heatsink strong solvents should not be used as they may damage the ampliﬁer. Do not use compressed air, because solids can

penetrate inside the ampliﬁer. Cleanings best done with wet towels or cloth.

8. Make sure that the location of the ampliﬁer does not violate the proper operation of mechanical and electrical devices of

the vehicle.

9. Make sure that during the installation and connection of the battery, the power cables are not shorted.

10. When performing plumbing, drilling or cutting works with the car, make sure that there is no wiring, brake lines, fuel pipe

or other structural elements under the place of work. Follow the safety rules! Use protective glasses and gloves.

11. To protect the wires use rubber gaskets if the wire passes through a hole in the plate, or other similar materials if it lies

close to the parts exposed to heat.

12. Make sure that all the cables are ﬁxed over the entire length. Also make sure that their outer protective shell is non-

combustible. Use a clamping screw to secure the positive and negative cables next to the appropriate terminals of the ampliﬁer.

13. Select a diameter of the power cable in accordance with the power of the ampliﬁer and the recommendations provided

here. Power cables are extremely important since they directly aﬀect the system damping factor and sound quality. The cables to

the battery must be in the copper crimp terminals pressed with the help of a hydraulic press, and well ﬁxed to the battery

terminals.

14. To avoid accidental damage, keep the ampliﬁer in its original packaging prior to installation.

15. Use high-quality copper speaker and power cables.

CAUTION!!! High sound pressure can damage your health!

Please use the common sense when controlling volume!

1. INTRODUCTION

2. SAFETY I N S T R U C T I O N S

1. Before installing the ampliﬁer disconnect the battery from the electrical system.

2. To connect the ampliﬁer it is necessary to stretch the power cable from the location of the battery to the place of installation

of the ampliﬁer. Select the power cable with the appropriate regulations in AWG (see Table: Selection of the diameter of the

power cables)

3. Connect the power supply with the correct polarity. Connect all (+) terminals of the ampliﬁer to the cable from the positive

terminal of the battery and the (-) terminals of the ampliﬁer – to the cables running from the negative terminal of the battery.

4. Place the fuse holder for each positive cable within 40 cm from the positive terminal of the battery and connect one end of

the power cable to the holder after connecting the other end to the ampliﬁer. Do not install the fuse.

5. Route all signal cables next to each other and separately from the power cables.

6. Connect the wires of RCA input. The input signal power must be between 0.2 V and 6 V.

7. To connect the power wire supply is necessary to use special power cables.

8. Fasten the ampliﬁer properly when installing it in the vehicle. If the component is disconnected during driving, it may cause

serious damage to the passengers of the vehicle or another vehicle. It is not recommended to screw the ampliﬁer directly to the

metal it can lead to distorsions at the signal outputs.

9. After installation is complete, check the wiring of the system and make sure that all connections have been made correctly.

Before installing the fuses, disconnect the positive lead from the battery and then install the fuse in the fuse holder. Using the light

bulb 12 V 21 W, connect the positive lead to one contact of the bulb and the other contact of the bulb to the positive terminal of

the battery.

When properly connected, the bulb must brieﬂy light up and go out. Now you may connect the positive lead to the (+)

battery. If the light does not go out, then something is wrong. This will prevent damage to the ampliﬁer in case of reverse polarity

and unwanted sparks when connecting. Install the rest of the fuses.

10. To activate the ampliﬁer, it is necessary to apply the positive potential of 12 volts to the control input of the ampliﬁer (REM)

through a switch or a corresponding control output (REMOTE OUT) with the head unit (HU).

11. LED indicator on the front panel lights up in green, indicating that the device is turned on. LED indicator lights up in red

when the outputs are overloaded, if the temperature protection is activated, if there is a short circuit in the system cables to the

heatsink and if the ampliﬁer is faulty.

12. The sound level is calibrated by adjusting the volume of the source up to 3/4 of its maximum level. Then, adjust the

sensitivity level of the ampliﬁer up until you hear distortions.

3. TYPICAL I N S TA L L AT I O N SEQUENCE

Serial connectio n

Parallel connectio n

SC HE ME S OF E N A BL IN G T H E L O A D O F T H E S U B WO OF ER

Voice coils 1+1 , 2 + 2 , 4 + 4 O h m

Total impedance = ΩSu b 1 + ΩSu b 2 + ΩSub 3 ...

ΩSu b 1 + ΩSub 2 + ΩSu b 3 .. .

Total impedance = 1

...

The minimum permissible load impedance at the output of the ampliﬁer is 1 ohm. Use these formulas to calculate the

load impedance of various types of connections.

4. C O N N E C T I O N METHODS EN

The subwoofer has voice coil D1, D2 or D4.

2+2 Ohm

4+4 Ohm 8 Ohm

4 Ohm

1+1 Ohm 2 Ohm

Voice coils Total impedance

2+2 Ohm

4+4 Ohm 2 Ohm

1 Ohm

1+1 Ohm 0,5 Ohm

Voice coils Total impedance

One subwoofer, coils in parallel

One subwoofer, coils in series

Subwoofers in seri e s , c o i l s i n p a r a l l e l

2+2 Ohm

4+4 Ohm 4 Ohm

2 Ohm

1+1 Ohm 1 Ohm

Voice coils Total impedance

In any case do not expose the amplifier to the loads lower than specified by the manufacturer. Use these schematics to

calculate load impedance of different connection types.

2+2 Ohm

4+4 Ohm 6 Ohm

3 Ohm

1+1 Ohm 1,5 Ohm

2+2 Ohm

4+4 Ohm 16 Ohm

8 Ohm

1+1 Ohm 4 Ohm

2+2 Ohm

4+4 Ohm 24 Ohm

12 Ohm

1+1 Ohm 6 Ohm

Voice coils Total impedance

Subwoofer in series, c o i l s i n s e r i e s

2+2 Ohm

4+4 Ohm 8 Ohm

4 Ohm

1+1 Ohm 2 Ohm

Voice coils Total impedance

2+2 Ohm

4+4 Ohm 32 Ohm

16 Ohm

1+1 Ohm 8 Ohm

Voice coils Total impedance

2+2 Ohm

4+4 Ohm 4 Ohm

2 Ohm

1+1 Ohm 1 Ohm

Voice coils Total impedance

Subwoofers in paralle l , c o i l s i n s e r i e s

2+2 Ohm

4+4 Ohm 2,66 Ohm

1,33 Ohm

1+1 Ohm 0,66 Ohm

2+2 Ohm

4+4 Ohm 1 Ohm

0,5 Ohm

1+1 Ohm 0,25 Ohm

Voice coils Total impedance

2+2 Ohm

4+4 Ohm 2 Ohm

1 Ohm

1+1 Ohm 0,5 Ohm

Voice coils Total impedance

2+2 Ohm

4+4 Ohm 0,66 Ohm

0,33 Ohm

1+1 Ohm 0,16 Ohm

Voice coils Total impedance

Subwoofers in paralle l , c o i l s i n p a r a l l e l

CAUTION!!! High sound pressure can damage your health!

Please use the common sense when controlling volume!

Connect the head unit (HU) to low-level inputs of the ampliﬁer using RCA cable.

5. W I R I N G DIAGRAMS

MA - 3 5 0 . 1 D , MA -4 5 0 . 1 D , MA -8 0 0 . 1 D , MA -1 5 0 0 . 1 D , MA -2 0 0 0 . 1 D

2+2 Ohm

4+4 Ohm 0,5 Ohm

0, 5 Ohm2

1+1 Ohm 0,125 Ohm

Voice coils Total impedance

Connect the speaker cables from the positive and negative terminals of the speakers to the respective outputs of the ampliﬁer

terminal marked with SPEAKER, as shown at the diagram. To connect the power wire supply it is necessary to use special power

cables. The fuse is placed in the holder and ﬁxed in the cable cut. One end of the cable is connected to the positive terminal of the

battery, the second one – to the ampliﬁer terminals marked with + 12V. Be sure to use a fuse with the parameters suﬃcient for use

in the system.

The length and diameter of the grounding cable must conform to the length and diameter of the cable + 12V. Connect

one end to the negative terminal of the battery and the other end of the grounding cable to the terminals marked with

GND.

Caution!!! The minimum permissible connection load impedance is 1 ohm.

For models MA-350.1D, MA-450.1D, MA-800.1D, MA-1500.1D, MA-2000.1D the operating voltage is 9-15 V.

Standard wiring diagram

MA - 3 5 0 . 1 D , MA -4 5 0 . 1 D , MA -8 0 0 . 1 D , MA -1 5 0 0 . 1 D

MA - 2 0 0 0 . 1 D

Application of connecto r s a n d c o n t rols

MA - 3 5 0 . 1 D , MA -4 5 0 . 1 D , MA -8 0 0 . 1 D , MA -1 5 0 0 . 1 D , MA -2 0 0 0 . 1 D

MA - 3 5 0 . 1 D , MA -4 5 0 . 1 D , MA -8 0 0 . 1 D , MA -1 5 0 0 . 1 D

1. POWER - LED for operation (green) / PROTECT - LED for protection (red)

2. REMOTE - input for connection of the bass remote control

3. INPUT - signal input, RCA jacks

4. BASS EQ - bass level adjustment 0 dB, 6 dB, 12 dB at 45 Hz

5. GAIN – input signal level adjustment 0.2 V - 6 V

6. LPF – low pass ﬁlter 50 Hz - 220 Hz (24 dB/Oct)

7. SUBSONIC – subsonic frequency ﬁlter off (0 Hz) - 50 Hz (24 dB/Oct)

1. SPEAKER OUTPUT “-” – speaker negative terminal connections

2. SPEAKER OUTPUT “+” – speaker positive terminal connections

3. BATT+ – power supply terminals +12 V

4. GND - grounding supply terminals

5. REM – connector of remote activation of the ampliﬁer

Remote control

1. Bass remote control

1. GND - grounding supply terminals

2. REM – connector of remote activation of the ampliﬁer

3. BATT+ – power supply terminals +12 V

4. SPEAKER OUTPUT “+” – speaker positive terminal connections

5. SPEAKER OUTPUT “-” – speaker negative terminal connections

MA - 2 0 0 0 . 1 D

Power RMS 4 Ohm*

Power RMS 2 Ohm*

Power RMS 1 Ohm*

Low pass ﬁlter

Subsonic ﬁlter

Bass EQ (bass level adjustment)

Frequency response

Input sensitivity

Signal to noise ratio

Damping factor

Model

Fuse (single)

Input terminal connection

Output terminal connection

Working voltage

Size (WхLхH mm)

170 W x 1

280 x 1W

350 W x 1

50 - 220 Hz

oﬀ Hz - 50

0, 6, 12 dB

20 - 250 Hz

0.2 V- 6 V

> 85 dB

> 150

40 А

4 AWG (21 mm²)

8 AWG (8,4mm²)

9 V - 15 V

202 x 159 х 59.5

180 W x 1

310 W x 1

450 W x 1

217 x 159 х 59.5

320 W x 1

550 W x 1

800 W x 1

50 - 220 Hz

oﬀ Hz - 50

0, 6, 12 dB

20 - 250 Hz

> 105 dB

> 150

60 А

9 V - 15 V

50 - 220 Hz

oﬀ Hz - 50

0, 6, 12 dB

20 - 250 Hz

> 105 dB

> 150

80 А

9 V - 15 V

294.5 x 159 х 59.5

4 AWG (21 mm²)

8 AWG (8,4mm²)

4 AWG (21 mm²)

8 AWG (8,4mm²)

600 W x 1

1000 W x 1

1500 W x 1

50 - 220 Hz

oﬀ Hz - 50

0, 6, 12 dB

20 - 250 Hz

> 85 dB

> 150

120 А

9 V - 15 V

374 x 159 х 59.5

800 W x 1

1500 W x 1

2000 W x 1

MA-350.1D MA-450.1D MA-800.1D MA-1500.1D MA-2000.1D

50 - 220 Hz

oﬀ Hz - 50

0, 6, 12 dB

20 - 250 Hz

> 105 dB

> 150

200 А

9 V - 15 V

485 x 159 х 59.5

4 AWG (21 mm²) 4 AWG (21 mm²)

8 AWG (8,4mm²) 8 AWG (8,4mm²)

7. S P E C I F I C ATIONS

0.2 V- 6 V 0.2 V- 6 V 0.2 V- 6 V 0.2 V- 6 V

*RMS Power at 14.4 V, THD 1%

Size (WхLхH inch)7.95 x 6.26 х 2.34 8.54 x 6.26 х 2.34 11.59 x 6.26 х 2.34 14.72 x 6.26 х 2.34 19.09 x 6.26 х 2.34

Crossover 24 dB / Oct 24 dB / Oct 24 dB / Oct 24 dB / Oct 24 dB / Oct

Use the table below to select the desired diameter based

on the length and the current consumption.

Use the table below to select the desired diameter based

on the length and the power consumption.

6. SELECTION OF THE DIAMETER OF POWER CABLES AND SPEAKERS CABLES

Sel ect ion o f th e d ia m et er

of th e pow er ca bl e s

Sel ect ion o f th e d ia m et er

of th e spe ake r ca b le s

The minimum permissible resistance 1 Ohm 1 Ohm 1 Ohm 1 Ohm 1 Ohm

1. Ampliﬁer – 1 pcs.

2. Owner's Manual – 1 pcs.

3. Warranty card – 1 pcs.

4. Mounting Kit – 1 pcs.

5. Remote control – 1 pcs.

Deaf Bonce ampliﬁers of Machete series are high-quality and technically perfect products. The problems often arise due to

improper use, faulty connection of components or lack of power supply of the on-board network.

1) The ampliﬁer does not turn on.

Problem solution: Check all the contacts and the presence of 9-15 V at the ampliﬁer terminals. Check whether the control input

of the ampliﬁer "REM" receives the positive potential of 12 V.

2) Power turns on, but goes into protection (security indicator lights up)

Problem solution: Check if there is a short circuit (fault) on the ampliﬁer output which is connected to the speakers or

subwoofers. Make sure that commutation of the voice coils of the subwoofer is correct. The rated impedance of the voice coils

should not be lower than the permissible rated load impedance of the ampliﬁer. Check the supply voltage of the ampliﬁer. It must

be within the range of 9-15 V for 15V versions of ampliﬁers.

3) The ampliﬁer turns on but at a high volume it goes to protection. Problem solution: The ampliﬁer may lack power. Make sure

that the rated current of the alternator and the battery capacity is enough to power this ampliﬁer.

Check the ampliﬁer for overheating. Check the load impedance.

4) The ampliﬁer is turned on, but there is no sound from the speakers or subwoofer.

Problem solution: Check the connection of the ampliﬁer, the integrity of the interconnecting cable, HU, the speaker or the

subwoofer.

8. P O S S I B L E FA U LT S A N D TH E I R SOLUTIONS

9. B O X CONTENTS

Items marked “crisscrossed wheeled bin” are not allowed to be disposed of together with usual household waste. These

electrical and electronic products should be disposed of in special reception centers, equipped for recycling such products and

components. For information about the location of the nearest disposal / recycling spot and the rules of delivery of waste please

contact your local municipal oﬃce. Recycling and proper disposal helps to protect the environment and prevent harmful eﬀects

on health.

10. WA R R A N T Y AN D MAINTENANCE I N F O

Deaf Bonce products of Machete series are warranted against defects concerning materials and their manufacturing under

normal functioning conditions.

While the product is under warranty, defective parts will be repaired or replaced at the manufacturer's discretion. The

defective product, along with notiﬁcation about it, must be returned to the dealer from which it was purchased together with the

warranty certiﬁcate duly ﬁlled in, . If the product is no longer under warranty, it will be complete with the original packaging

repaired at the current costs.

Our company does not undertake any liability for damages due to transportation. Our company does not take any

responsibility for costs or loss of proﬁt due to the impossibility to use the product, other accidental or consequential costs,

expenses or damages suffered by the customer. Warranty according to laws in force. For more information visit our website and

carefully read warranty card. The manufacturer reserves the right to change design and specification without prior notice.

11. I N F O R M AT I O N ON DI S P O S A L OF TH E ELECTRICAL A N D

ELECTRONIC E Q U I P M E N T (F O R T H E EU R O P E A N COUNTRIES W I T H

SEPA R AT E W A S T E C O L L E C T I O N )

http://deafbonce.com

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali dB Amplificatore per auto

dB OKUR A5 125.4 Manuale utente

Manuali Amplificatore per auto popolari di altre marche

Cyfre

Cyfre CHACDMA-819 Manuale utente

MTX

MTX Thunder Marine TM904 Manuale utente

MTX

MTX Thunder TA Super TA92001 Manuale di istruzioni

Lanier

Lanier 480-0239 Istruzioni operative e di manutenzione

Kenwood

Kenwood KAC-642 Manuale utente

Pioneer

Pioneer GM-D8500M Manuale utente

Jensen

Jensen XA4150 Manuale utente

Sony

Sony XM-405EQX Marketing Specifications Manuale utente

Audiopipe

Audiopipe AQX-660.2 Manuale utente

Clarion

Clarion APA2001 APA2001 APA2001 Guida rapida

Sony

Sony XM-7547 Manuale utente

Alpine

Alpine PDX11000 - Amplifier Manuale utente

Steg

Steg Qx Mos 105.4x Manuale utente

JL Audio

JL Audio HD900/5 Manuale utente

Memphis

Memphis 16-MC5.700 Manuale utente

Audiopipe

Audiopipe APSM-1150 Manuale utente

Boss Audio Systems

Boss Audio Systems Riot GT1000M Manuale utente

Kenwood

Kenwood KAC-PS811D Manuale utente

dB MA-350.1D Manuale utente

Manuali Amplificatore per auto popolari di altre marche