DCS WDS-27 Manuale utente
THE PROFESSIONAL WARMING DRAWER
Installation Guide
MODELS:
WDI
WDS-27
WDS-30
Thank you for selecting this DCS Warming Drawer. Because of its unique features, we have developed this
Installation Guide. It contains valuable information on how to properly install your new Warming Drawer
for years of safe and enjoyable use.
To help serve you better, please fill out and submit your Ownership Registration Card by visiting our website
at www.dcsappliances.com and selecting“Customer Service”on the home page and then select“Ownership
Registration”. You may also submit the enclosed Ownership Registration Card by mail to the address below.
In addition, keep this guide handy, as it will help answer questions that may arise as you use your new
appliance.
For your convenience, product questions can be answered by a DCS Customer Service Representative by
phone:1-888-281-5698.
WARNING
The warming drawer is not intended to be used in conjunction with water. DO
NOT fill the drawer or warming cavity with water. Doing so could create a
shock hazard resulting in a possible injury.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP
GREASE FIRE, OBSERVE THE FOLLOWING: SMOTHER FLAMES with a close-
fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO
PREVENT BURNS. If the flames do not go out immediately EVACUATE AND CALL
THE FIRE DEPARTMENT. NEVER PICK UP A FLAMING PAN - You may be burned.
DO NOT USE WATER, including wet dishcloths or towels - a violent steam
explosion will result. Use an extinguisher ONLY if:
1.You know you have a Class ABC extinguisher, and you already know how
to operate it.
2.The fire is small and contained in the area where it started.
3.The fire department is being called.
4.You can fight the fire with your back to an exit.
DCS
Attention: Customer Service
5800 Skylab Road
Huntington Beach, CA 92647
www.dcsappliances.com
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
A MESSAGE TO OUR CUSTOMERS
1
TABLE OF CONTENTS
2
SAFETY PRACTICES & PRECAUTIONS...........................................................................................................3-4
FEATURES................................................................................................................................................................................5
INSTALLATION INSTRUCTIONS........................................................................................................................6-10
Specifications............................................................................................................................................................6
Mounting Installation ........................................................................................................................................7-8
Warming Drawer Integrated ...............................................................................................................................9
Wall Oven and Microwave and Warming Drawer Installation................................................................9
WIRING DIAGRAM..........................................................................................................................................................10
SERVICE ..................................................................................................................................................................................11
WARRANTY..........................................................................................................................................................................12
READ AND UNDERSTAND THESE PRECAUTIONS
Read this Installation Guide thoroughly before installation. This will help to reduce the risk of
fire, electric shock, or injury to persons.
Remove all packaging materials from your appliance.
Install according to instructions. See page 6-9 to insure proper installation and servicing.
Be sure to have a qualified service technician install and ground this appliance.
Plug into rated outlet: 120 Volts AC, 5 amp minimum circuit requirement.
PREHEATING INSTRUCTIONS
The Warming Drawer is designed to keep cooked foods warm for extended periods of time. The
drawer must be pre-heated before use on high (see Use and Care Guide). If the warming drawer isn’t
pre-heated, the internal temperature of the food being warmed could fall below the minimum safe
level and bacteria could develop. Always preheat the drawer according to the instructions described
in the warming drawer Use and Care Guide.
Children should not be left alone or unattended in an area where appliances are in use. They
should never be allowed to turn knobs, push buttons, sit or stand on any part of an appliance.
Children in walkers, or children crawling can be attracted to the round door handle and may
grab and open the warming drawer. This can result in injury from the door being pulled open
on a child, or severe burns if it is in use and hot.
WARNING:
Do not store items of interest to children in, above or around any appliance.
Children could be seriously injured if they should climb onto the appliance to
reach these items.
Be certain to use only dry pot holders:Moist or damp pot holders on hot surfaces may cause burns
from steam. Do not use a towel or other bulky cloth in place of pot holders.
Never store anything in the warming drawer. Flammable materials can catch fire, plastic items
may melt or ignite and other types of items could be ruined.
Do not hang articles from any part of the appliance or place anything against the drawer. Some
fabrics are quite flammable and could catch on fire.
For safety reasons and to avoid damage to the appliance, never sit, stand, or lean on the
warming drawer door.
For personal safety, wear proper apparel. Loose fitting garments or hanging sleeves should
never be worn while using this appliance. Some synthetic fabrics are highly flammable and
should not be worn while using this appliance.
Do not use aluminum foil to line any part of the warming drawer. Using a foil liner could result
in a fire hazard, or the obstruction of the flow of heat and ventilation air. Foil is an excellent heat
insulator and heat will be trapped underneath it. This trapped heat can upset the performance
of the warming drawer parts.
WARNING:
This appliance is designed for warming food. Based on safety considerations,
never use the warming drawer to warm or heat a room.
SAFETY PRACTICES AND PRECAUTIONS
3
SAFETY PRACTICES & PRECAUTIONS
As with any cooking or heating appliance, never leave the warming drawer unattended when
warming food, this could be a fire hazard.
Only certain types of glass, heat proof glass-ceramic, ceramic, earthenware or glazes are
suitable for use in this warming drawer. Utensils that are not thermally heat safe may break
with sudden temperature changes.
Never heat unopened containers, a build up of pressure may cause the container to burst.
Grease is flammable, avoid letting grease deposits collect in the warming drawer, clean up
spillage.
DO NOT use water on grease fires. Turn OFF the warming drawer, then smother the fire with
baking soda or use a dry chemical or foam-type fire extinguisher.
When opening the drawer while keeping sauces warm, tomato sauce, etc., the drawer must be
opened slowly to avoid spillage.
Use care when opening a hot warming drawer;to avoid severe burns,open slowly,allow the hot
air or steam to escape before reaching in to remove or replace any foods.
Do not repair or replace any part of this appliance unless it is specifically recommended in this
manual. All other servicing should be referred to a qualified Service Technician. Service
Technicians must disconnect the power supply before servicing this appliance.
When using the warming drawer: DO NOT TOUCH THE INTERIOR SURFACES or the exterior
area immediately surrounding the door until it has had sufficient time to cool to avoid burn
injuries.
Clean the warming drawer with caution. Avoid steam burns; do not use a wet sponge or cloth
to clean the appliance while it is hot. Some cleaners produce noxious fumes if applied to a hot
surface. Follow directions provided by the cleaner manufacturer.
Be sure all the controls are turned off and the appliance is cool before using any type of aerosol
cleaner on or around the appliance. The chemical that produces the spraying action could, in
the presence of heat, ignite or cause metal parts to corrode.
Do not touch the heating element or interior surfaces of the warming drawer, even if they
appear dark in color. They may still be hot enough to cause burn injury, allow sufficient time to
cool.
Do not allow flammable materials which may ignite to come in contact with the hot heating
element or the interior surface of the warming drawer until the unit has had a sufficient time to
cool.
4
FEATURES
5
Moist/
Crisp
Knob
Power
Indicator
Lens
Thermostat
Control
Knob
Stainless
Steel
Tray
Power
Indicator
Light
Stainless
Steel
Drawer
*
Fig. 01
* Moist/crisp feature not available on fully integrated model (WDI).
INSTALLATION INSTRUCTIONS
6
WDS-27
WDS-30
A
9-7/8” 25-5/16”
9-7/8” 25-5/16”
24” (min.)
24” (min.)
SPECIFICATIONS
The cabinet depth from the outer edge of the face frame to the inside back of the cabinet or wall
should be at least 24” (see figure 02).
The Warming Drawer should be installed into a base cabinet with minimum outside dimensions of
13-1/4” high by 30” wide by 24” deep for 30”models. For 27” models 13-1/4” high by 27” wide by 24”
deep. For WDI Model 15-1/4” high by 26-3/4” wide by 24” deep (see figure 03 and figure 04).
Power supply required: 120VAC; 5A min., 15A max. circuit.
A
BC
1-1/2" min.
to bottom of
countertop
A 120 volt AC
outlet should be
located below the
Warming Drawer
2x4's or similar
support
10-1/4"
WDS-27 – 26-7/8 "
WDS-30 – 29-7/8"
23-7/8"
25-1/16"
28-3/16"
POWER
CORD
9-7/8"
24"
POWER
CORD
9-7/8"
11-7/8"
1"
11-1/4"
BC
CUTOUT DIMENSIONS
Fig. 02
Fig. 03 Fig. 04
CUT OUT DIMENSIONS
WARMING DRAWER DIMENSIONS
(FRONT VIEW)
WDS-27 & WDS-30 DIMENSIONS
(SIDE VIEW)
WDI
11-1/4” 26-1/8” 24” (min.)
WDI
MOUNTING INSTALLATION
The lower rear corners of the cabinet need to provide proper support to the back of the Warming
Drawer and the anti-tip mounting clips. A 120 volt AC outlet should be located no further than 36
inches from the back center of the Warming Drawer. Illustrations suggest one possible bottom
support, but the consumer is not limited to this idea for mounting configuration.
STEP 1
The bottom rear section of the cabinet should be made of solid plywood or 2x4 and needs to be
installed to hold the anti-tip mounting clips and support the weight of Warming Drawer, which is
90 lbs.
STEP 2
Use the screws provided to attach the mounting clips which must be installed for anti-tip safety to the
bottom support at the back. See placement dimensions in figure below.
STEP 3
The Warming Drawer has slots on the back side where it will slide onto the anti-tip mounting clips.
See page 8. Plug power cord into AC outlet.
STEP 4
Fasten the front face to the cabinet by passing the screws through the holes of the front face of the
warming drawer to finish the installation. See page 8.
NOTE: Bottom support made of plywood or other solid wood construction capable of supporting
the weight of the warming drawer.
INSTALLATION INSTRUCTIONS
7
Slide drawer
on to Anti-Tip
mounting clips
mounting clips
WDS – 21-1/2"
WDI – 21-7/8"
Fig. 05
INSTALLATION INSTRUCTIONS
8
Center line
to Center line
for mounting clips for
WDS-30
WDS-27
21-1/8"
WDI
Fig. 06
Fig. 07
INSTALLATION INSTRUCTIONS
9
WARMING DRAWER INTEGRATED (WDI)
Custom Panel Installation
1. Remove drawer as per instructions. (See Use & Care Manual.)
2. Check the dimensions of the front template. (See fig. 08.)
3. Cut the custom panel to required dimensions, knowing that the panel must cover the front
template plus 1/8” on all four sides for a good presentation.The thickness of the custom panel
must be greater than 3/8” to allow for clearance of the tips of the screws holding the drawer
when the custom panel is mounted.
4. Center the paper template provided on the back of the custom panel to pre-drill 1/4” holes
(5/16” depth) to allow for clearance of the tips of the screws holding the drawer.
5. Fasten the custom panel with the supplied screws as shown in fig. 08 .
Fig. 08
11-7/8”
26-3/4”
Front template
( WDI only)
Screws to hold
custom panel to
Warming Drawer
Fig. 09
Custom Panel
Use template
provided
27”
12-1/8”
Holes to drill
Altri manuali per WDS-27
1
Questo manuale è adatto per i seguenti modelli
2
Indice
Lingue:
Altri manuali DCS Cassetto scaldavivande
DCS
DCS WDI Manuale utente
DCS
DCS WD-27-SS-OD Guida all'installazione
DCS
DCS WDS-27 Manuale utente
DCS
DCS WDU Istruzioni per il montaggio
DCS
DCS ADR24 Manuale utente
DCS
DCS WDU models Istruzioni per il montaggio
DCS
DCS Professional Warming Drawer WDT-30 Manuale utente
DCS
DCS WDI Manuale utente
DCS
DCS RF24DE Manuale
DCS
DCS WDT-30 WDTI Manuale utente
