De Agostini Model Space C57 Manuale utente

Build the

Steam

Locomotive

Pack 11

Contents

Step by step Page

Editorial and design by Continuo Creative, 39-41 North Road, London N7 9DP.

Published in the UK by De Agostini UK Ltd, Battersea Studios 2, 82 Silverthorne Road, London SW8 3HE.

Published in the USA by De Agostini Publishing USA, Inc.,121 E. Calhoun Street, Woodstock, IL 60098.

Warning: Not suitable for children under the age of 14. is product is not a toy and is not designed or

intended for use in play. Items may vary from those shown.

Build the

Steam

Locomotive

Stage 83: Detailing the tender 4

Stage 84: The base 1

Stage 85: The base 2

Stage 86: The base 3

Stage 87: The base top

Stage 88: The speaker

Stage 89: The switchboard and battery box

Stage 90: The sound eects generator

Stage 91: The track

190

192

194

196

198

200

202

204

206

Tools

Where your parts t

190

Step by step: Stage 83

Detailing the tender 4

Tender upper plate

Buer

Coupling buer

Brake hose

Drawbar pin

Screws (2 x 4mm) x 7

Phillips screwdriver

Synthetic rubber adhesive (SRA)

Tweezers

Pliers

Familiarise yourself with the coupling

buer using the photo above as a guide.

Line the part up to the circled holes at the

rear of the tender.

Use two 2 x 4mm screws to secure it.

Your parts

Shorter side on top

Tender upper plate Brake hoseBuer

191

Your assembly

should look like

this.

Complete

Instant adhesive

Lower the

tender upper

plate into the

top of the

tender, as

shown.

Turn the tender

upside down and

t the drawbar

pin into the

circled hole using

tweezers. You can

remove the front

truck to make

this easier.

Now line up the

buer to the

circled holes at

the front of the

tender. It does

not matter

which way

round it goes.

Use pliers to

tighten the pin

into place.

Use two 2 x 4mm

screws to secure

the upper plate to

the tender via the

circled holes.

Use two more

2 x 4mm screws to

secure the buer

to the tender.

Fit the brake hose,

positioned as

shown on the rear

of the tender, into

the circled hole and

secure with SRA.

Once everything

is in place,

reinforce the

brake hose from

the back, using

instant adhesive.

Your assembly

should look

like this.

Now take the

overow pipe

from Stage 81

and use SRA to

secure it via the

two circled holes.

Forward Front

Overhang at bottom

Complete

Tools

Where your parts t

192

Step by step: Stage 84

The base 1

Front end frame

Side frame A

Side frame B

Frame joint

Cap bolts x 8

Hex wrench

Familiarise yourself

with side frames A

and B.

Now do the same for

the front end frame and

frame joint.

Longer space between

holes and frame ends

Painted edge on top

Frame joint

Front end frame

Indent

Front Front

Front

Your parts

Work of this issue

Front base section

Hex wrench

193

Lay out all four parts as shown above.

Lay the base face down on a at surface to ensure all the holes are aligned,

then secure the frame joint with four half-tightened cap bolts.

Line up the holes at each joint,

and insert a cap bolt into each.

Then use the hex wrench to

further tighten the bolts – but

only lightly at this stage to allow

room for adjustment.

Tighten the cap bolts by hand, as far

as you can.

Painted top faces down

All parts upside down

Front end

frame

Complete

Indent

Tools

Where your parts t

194

Step by step: Stage 85

The base 2

Frame joint

Side frame C

Side frame D

Rear end frame

Hex bolts x 8

Hex wrench

Note the dierence

between the side

frames C and D –

there is a long hole

in D.

Now do the same for the rear

end frame and frame joint.

Your parts

Rear

Long hole

Painted tops

Rear base section

This stage’s parts

Front

Frame joint

Rear end frame

195

Complete

Rear

Lay out all four parts as shown above.

Lay the base face down on a at surface to ensure all the holes are aligned,

then secure the frame joint with four half-tightened cap bolts.

Line up the holes at each joint,

and insert a cap bolt into each.

Then use the hex wrench to further

tighten the bolts – but only lightly

at this stage to allow room for

adjustment later.

Tighten the cap bolts by hand, as far

as you can.

Painted top faces down

All parts upside down

Indent

Tools

Where your parts t

196

Step by step: Stage 86

The base 3

Side frames E x 3

Frame joint

Side frame F

Cap bolts x 16

Hex wrench

Note the dierence between the three side frames E and the single F. There is an indent cut

into frame F.

Your parts

Indent

Front

Middle base section

This stage’s parts

197

Lay out this stage’s parts, along with the front and rear base sections, upside

down on your work surface as shown.

Lay the assembly out on a at surface and connect the central section to the

two end sections. Then tighten all 16 cap bolts fully.

Complete

Front

E F

Indents

Front base

section

Rear base

section

Indents

Indent

Long hole

Front

All parts upside down Line up the holes in the side frames with

those in the centre joint, and insert a cap

bolt into each.

Then use the hex wrench to further

tighten the bolts – but only lightly

at this stage to allow room for

adjustment. Repeat this for all sides

(E and F).

Tighten the cap bolts by hand, as far

as you can.

Altri manuali per Model Space C57

Altri manuali De Agostini Giocattolo

De Agostini

De Agostini Model Space MiG-29 Manuale utente

De Agostini

De Agostini Model Space C57 Manuale utente

De Agostini

De Agostini MODEL SPACE SUZUKI GSX 1300R HAYABUSA Manuale utente

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manuale utente

De Agostini

De Agostini Model Space IJN Akagi Manuale utente

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manuale utente

De Agostini

De Agostini Model Space MiG-29 Manuale utente

De Agostini

De Agostini Model Space MiG-29 Manuale utente

De Agostini

De Agostini Millennium Falcon 3 Series Manuale utente

De Agostini

De Agostini Model Space T-72 Manuale utente

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manuale utente

De Agostini

De Agostini MODEL SPACE Honda CB750 FOUR Manuale utente

De Agostini

De Agostini MODEL SPACE Soleil Royal Manuale utente

De Agostini

De Agostini Model Space MiG-29 Manuale utente

De Agostini

De Agostini Model Space T-72 Manuale utente

De Agostini

De Agostini Model Space D51 200 Manuale utente

De Agostini

De Agostini Model Space MiG-29 Manuale utente

De Agostini

De Agostini Model Space SANTISIMA TRINIDAD Manuale utente

De Agostini

De Agostini Model Space C57 Manuale utente

De Agostini

De Agostini Model Space MiG-29 Manuale utente

De Agostini

De Agostini Model Space ROBI Pack 03 Manuale di istruzioni

De Agostini

De Agostini Model Space MiG-29 Manuale utente

De Agostini

De Agostini Model Space Harley-Davidson FLSTF Fat Boy Manuale utente

De Agostini

De Agostini Model Space T-72 Manuale utente

Manuali Giocattolo popolari di altre marche

marklin

marklin 37321 Manuale utente

Canon

Canon PAPER CRAFT Manuale utente

GREAT PLANES

GREAT PLANES Pitts M-12S Manuale utente

NOCH

NOCH 14261 Manuale utente

Hausler

Hausler 450 SE V2 Manuale utente

Dynaflite

Dynaflite Daydream Manuale utente

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuale

Kenner

Kenner Batman 63651 Manuale utente

LEGO

LEGO 8527 Manuale utente

iKarus

iKarus ECO 8 Manuale utente

Multiplex

Multiplex EasyStar II Manuale di istruzioni

Walkera

Walkera 38 Manuale di istruzioni

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuale utente

MD MXION SWD Manuale utente

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuale utente

marklin

marklin 39671 Manuale utente

Meccano

Meccano 15103 Manuale utente

LEGO

LEGO TECHNIC 8735 Manuale utente