Dell PowerEdge 2600 Manuale utente
www.dell.com | support.dell.com
Dell™ Systems
Installing or Replacing an
ERA/O Card
5U106ebk3.book Page 1 Tuesday, April 15, 2003 1:22 PM
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury,
or death.
Information in this document is subject to change without notice.
© 2002–2003 Dell Computer Corporation. All rights reserved.
Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names
other than its own.
April 2003 P/N 5U106 Rev. A03
5U106ebk3.book Page 2 Tuesday, April 15, 2003 1:22 PM
Installing or Replacing an ERA/O Card 1-1
This document explains how to install or replace an Embedded Remote Access Option
(ERA/O) remote management card in your system.
Before You Begin
NOTE: For more information about setting up and using an ERA/O card, see the
remote access controller documentation provided on the documentation CD that came
with your system. The latest information about your ERA/O card is available at the
Dell Support website at support.dell.com.
Before installing the ERA/O card, record the system configuration settings. View the system
configuration screens in the System Setup program and make a note of each setting. See
your User's Guide for instructions about using the System Setup program.
Installing an ERA/O Card
CAUTION: Only trained service technicians are authorized to remove the system
cover and access any of the components inside the system. See your System
Information Guide for complete information about safety precautions, working
inside the computer, and protecting against electrostatic discharge.
1Open the bezel. See "Removing the Bezel" in your Installation and Troubleshooting
Guide.
2Turn off the system, including attached peripherals, and disconnect the system and
peripherals from their electrical outlets.
3Remove the cover. See "Removing the Cover" in your Installation and Troubleshooting
Guide.
5U106ebk3.book Page 1 Tuesday, April 15, 2003 1:22 PM
1-2 Installing or Replacing an ERA/O Card
www.dell.com | support.dell.com
4Remove the front fan assembly:
aDisconnect the front fan assembly power cable from the front fan connector on
the SCSI backplane board.
bRelease the fan assembly by pressing the release latch. See Figure 1-1.
cSwing the fan assembly up and out of the way.
Figure 1-1. Removing the Front Fan Assembly
release latch
5U106ebk3.book Page 2 Tuesday, April 15, 2003 1:22 PM
Installing or Replacing an ERA/O Card 1-3
5Remove any full-length expansion cards. If you do not have any expansion cards
installed, skip to step 6.
aUnfasten and remove the expansion-card latch. See Figure 1-2.
bDisconnect any cables attached to the card.
cGrasp the expansion card by its edges, and remove it from the expansion-card
connector on the system board.
Figure 1-2. Removing a Full-Length Expansion Card (If Installed)
expansion-card
latch
5U106ebk3.book Page 3 Tuesday, April 15, 2003 1:22 PM
1-4 Installing or Replacing an ERA/O Card
www.dell.com | support.dell.com
6Remove the expansion-card guide:
aPress the middle of the expansion-card guide in the direction of the SCSI
backplane (away from the system board) and carefully rotate the expansion-card
guide toward the system board until the card guide retention clip unhooks from
the system board. See Figure 1-3.
bSwing the expansion-card guide up and out of the way.
Figure 1-3. Removing the Expansion-Card Guide
expansion-card
guide
retention clip
slot
5U106ebk3.book Page 4 Tuesday, April 15, 2003 1:22 PM
Installing or Replacing an ERA/O Card 1-5
7Install the ERA/O card in the system:
aUnpack the ERA/O card.
If you are replacing an ERA/O card, see "Removing an ERA/O Card" for removal
instructions before continuing with the next step.
bPosition the ERA/O card so that the card connector is directly over the connector
on the system board and the mounting holes in the card line up with the support
posts on the system board. See Figure 1-4.
cPress down until the ERA/O card connector is fully seated in the connector on the
system board and the support posts are secured in the mounting holes on the card.
Figure 1-4. Installing the ERA/O Card
ERA/O card
connector
ERA/O card
system board
support posts (4)
mounting
holes (4)
5U106ebk3.book Page 5 Tuesday, April 15, 2003 1:22 PM
1-6 Installing or Replacing an ERA/O Card
www.dell.com | support.dell.com
8Reinstall the expansion-card guide:
aHolding the expansion-card guide at a 45-degree angle, insert the two tabs at the
ends of the expansion-card guide base into the slots on the system board. See
Figure 1-5.
bRotate the expansion-card guide down until the clip snaps securely onto the
system board.
Figure 1-5. Reinstalling the Expansion-Card Guide
9Reinstall expansion cards that you removed:
aPosition the expansion card so that the card-edge connector aligns with the
expansion-card connector on the system board. See Figure 1-2.
bInsert the card-edge connector firmly into the expansion-card connector until the
card is fully seated.
cWhen the card is seated in the connector, close the expansion-card latch.
NOTE: SCSI cables connected from an expansion card to the SCSI backplane
board should be routed under the front fan assembly.
dReconnect all expansion-card cables.
slots (2)
tabs (2)
5U106ebk3.book Page 6 Tuesday, April 15, 2003 1:22 PM
Installing or Replacing an ERA/O Card 1-7
10 Reinstall the front fan assembly:
aPlace the fan assembly in the hinge bracket and swing the fan assembly down until
the release lever snaps into place.
bConnect the fan assembly power cable to the front fan connector on the SCSI
backplane board.
11 Replace the system cover. See "Replacing the Cover" in your Installation and
Troubleshooting Guide.
NOTE: If the server management Ethernet connector has not been used before,
remove the cover that protects the connector before connecting a network cable. See
Figure 1-6 for the location of the connector.
12 Connect a network cable to the 10-Mbps server management Ethernet connector on
the system back panel. See Figure 1-6.
Figure 1-6. Server Management Ethernet Connector
13 Reconnect the system and peripherals to their electrical outlets, and turn them on.
14 Close the bezel.
15 Update the ERA/O card with the latest version of the ERA/O firmware, available at the
Dell Support website at support.dell.com.
See the RAC documentation provided on the documentation CD for
information about updating the firmware.
server management
Ethernet connector
5U106ebk3.book Page 7 Tuesday, April 15, 2003 1:22 PM
1-8 Installing or Replacing an ERA/O Card
www.dell.com | support.dell.com
Removing an ERA/O Card
NOTICE: Do not attempt to disconnect the ERA/O card from the connector on the
system board until you have unfastened the card from each of the four support posts.
1Unfasten each of the support posts from the card:
aCompress the clasp at the top of the support post while carefully lifting up on the
corner of the card to unseat the post. See Figure 1-7.
bRepeat step a for each support post.
2Lift the ERA/O card straight up and out of the chassis.
Figure 1-7. Removing an ERA/O Card
ERA/O card
connector
ERA/O card
system board support posts (4)
mounting holes (4)
5U106ebk3.book Page 8 Tuesday, April 15, 2003 1:22 PM
Altri manuali per PowerEdge 2600
6
Indice
Lingue:
Altri manuali Dell Hardware per computer
Dell
Dell EMC XC Core XC6520 Manuale
Dell
Dell PowerProtect DM5500 Manuale utente
Dell
Dell OptiPlex HUB Manuale utente
Dell
Dell PowerEdge 1650 Manuale utente
Dell
Dell Precision R5500 Manuale utente
Dell
Dell OptiPlex XE4 Small Form Factor Manuale utente
Dell
Dell POWEREDGE RAID H700 Manuale utente
Dell
Dell PowerVault 770N Manuale tecnico
Dell
Dell Latitude ON Manuale utente
Dell
Dell PowerEdge T710 Manuale tecnico
Dell
Dell PowerEdge H730P Manuale utente
Dell
Dell PowerEdge C8220X Manuale utente
Dell
Dell Precision FX100 Manuale del proprietario
Dell
Dell ADVANCED PORT REPLICATOR Manuale utente
Dell
Dell PowerEdge 2600 Manuale utente
Dell
Dell TrueMobile 1180 Manuale utente
Dell
Dell Alienware Graphics Amplifier Manuale utente
Dell
Dell A2463645 - 2 GB Memory Manuale di istruzioni
Dell
Dell Dimension 4600 Series Manuale utente
Dell
Dell qlogic qla2100 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
