Dell P2419HCB Manuale

Altri manuali per P2419HCB

1

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Philips

Philips 107C64 Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

LG

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione

LG

LG M1950D-PZ Manuale utente

Sceptre

Sceptre D40 Manuale utente

Hunt Electronic

Hunt Electronic HCD-15AH Manuale utente

1

DELL P2419HCB

1. Disassembly Procedures

S1

Turn off power

S2

Place the monitor on a soft cloth or

cushion.

Press and hold the stand-release

button.

Lift the stand up and away from the

monitor.

S3

Unlock 4 Rear Cover screws.

Disassemble Rear Cover and Middle

Frame according to the sequence as

the picture showed

(Screw Torque:9±1Kgf)

S4

Tear off the AL foil.

Pull out Control board cable, wire and

USB board cable.

Take down main shielding from middle

frame.

Tear off adhesive tape from LVDS

cable.

Pull out LVDS cable and take off main

shielding from panel

S5

Unlock 9 screws on middle frame

(Screw Torque: 3.5-4.0Kgf)

S6

Unlock 5 screws on bezel

2

DELL P2419HCB

(Screw Torque: 1.2-1.25Kgf)

S7

Disassemble middle frame and bezel

from panel

S8

Disassemble Mylar from Main Shielding

S9

Unlock 8 PCB screws

(Screw Torque: 8~9kgf)

S10

Take out I/F Board, SPS Board, LED

Driver Board from Main Shielding

Pull out I/F board cable and LED Driver

board cable from SPS Board

3

DELL P2419HCB

S11

Remove electrolyte capacitors (red mark) from printed circuit boards

S11-1 Cut the glue between bulk cap. and PCB with a knife

S11-2 Ensure cutting path within the glue, don’t touch bulk cap. or PCB

4

DELL P2419HCB

S11-3 Take out bulk cap. pin solder with soldering iron and absorber

S11-4 Lift the bulk cap. up and away from the PCB

5

DELL P2419HCB

2. Product material information

The following substances, preparations, or components should be disposed of or

recovered separately from other WEEE in compliance with Article 4 of EU Council

Directive 75/442/EEC.

Capacitors / condensers (containing

PCB/PCT)

No used

Mercury containing components

No used

Batteries

No used

Printed circuit boards (with a surface greater

than 10 square cm)

Product has printed circuit boards

(with a surface greater than 10 square

cm)

Component contain toner, ink and liquids

No used

Plastic containing BFR

No used

Component and waste contain asbestos

No used

CRT

No used

Component contain CFC, HCFC, HFC and

HC

No used

Gas discharge lamps

No used

LCD display > 100 cm2

Product has an LCD greater than 100

cm2

External electric cable

Product has external cables

Component contain refractory ceramic fibers

No used

Component contain radio-active substances

No used

Electrolyte capacitors (height

> 25mm, diameter > 25mm)

Product has electrolyte capacitors

(height >25mm, diameter > 25mm)

3. Tools Required

List the type and size of the tools that would typically can be used to disassemble the

product to a point where components and materials requiring selective treatment can be

removed.

Tool Description:

- Screwdriver

- Penknife

- Bar scraper