Dell Virtual Edge Platform 4600 Manuale utente
VEP4600
Setup Guide
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of
your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data
and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury,
or death.
Copyright ©2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are
trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective
owners.
2018 - 04
Rev. A00
Contents
1 About this guide...............................................................................5
Related documents................................................................................... 6
Information symbols..................................................................................6
2 Site preparations............................................................................. 7
Site selection..............................................................................................7
Cabinet placement.................................................................................... 8
Rack mounting...........................................................................................8
System ground...........................................................................................8
Fans and airow........................................................................................ 8
Power..........................................................................................................9
Storing components..................................................................................9
3 VEP4600 installation......................................................................10
Unpack...................................................................................................... 10
Ground cable............................................................................................. 11
Rack or cabinet installation.....................................................................12
Rack mount safety considerations...................................................13
Two-post installation................................................................................13
1U front-rack installation................................................................... 14
Four-post installation...............................................................................16
Optics installation.....................................................................................18
Optics removal................................................................................... 18
Platform power-up.................................................................................. 19
Power up sequence...........................................................................19
4 Specications............................................................................... 20
Chassis physical design.......................................................................... 20
Contents 3
5 Support.........................................................................................23
4 Contents
About this guide
This guide provides site preparation recommendations, step-by-step procedures for rack
mounting and desk mounting, inserting modules, and connecting to a power source.
CAUTION: To avoid electrostatic discharge (ESD) damage, wear grounding wrist
straps when handling this equipment.
WARNING: Only trained and qualied personnel can install this equipment. Read this
guide before you install and power up this equipment. This equipment contains two
power cords. Disconnect both power cords before servicing.
WARNING: This equipment contains optical transceivers, which comply with the
limits of Class 1 laser radiation.
Figure 1. Class 1 laser product tag
WARNING: When no cable is connected, visible and invisible laser radiation may be
emitted from the aperture of the optical transceiver ports. Avoid exposure to laser
radiation, and do not stare into open apertures.
Topics:
• Related documents
• Information symbols
1
About this guide 5
Related documents
For more information about the Virtual Edge Platform 4600 (VEP4600), see the following
documents:
•VEP4600 Installation Guide
•VEP4600 Release Notes
NOTE: For the most recent documentation, see the support site: www.dell.com/
support.
Information symbols
This book uses the following information symbols:
NOTE: The Note icon signals important operational information.
CAUTION: The Caution icon signals information about situations that could result in
equipment damage or loss of data.
WARNING: The Warning icon signals information about hardware handling that
could result in injury.
WARNING: The ESD Warning icon requires that you take electrostatic precautions
when handling the device.
6 About this guide
Site preparations
VEP4600 is universal customer premise equipment (uCPE). To connect the service provider
edge or enterprise branch to the cloud, use VEP4600 to host multiple virtual network
functions (VNFs), such as SD-WAN, routing, rewall, and deep-packet inspection.
For more information about VEP4600 specications, see Chassis physical design.
NOTE: Install the platform into a rack or cabinet before installing any optional
components.
Topics:
• Site selection
• Cabinet placement
• Rack mounting
• System ground
• Fans and airow
• Power
• Storing components
Site selection
Install your equipment in restricted access areas. A restricted access area is one where
service personnel can only gain access using a special tool, lock, key, or other means of
security. The authority responsible for the location controls access to the restricted area.
Ensure that the area where you install your platform meets the following safety
requirements:
• Near an adequate power source. Connect the platform to the appropriate branch circuit
protection according to your local electrical codes.
• Environmental—platform location—continuous temperature range is from 0°C to 45°C
(32°F to 113°F).
2
Site preparations 7
• Operating humidity is from 5 to 90 percent non-condensing, continuous.
• In a dry, clean, well-ventilated, and temperature-controlled room, away from heat sources
such as hot cooling vents or direct sunlight.
• Away from sources of severe electromagnetic noise.
• Positioned in a rack or cabinet, or on a desktop with adequate space in the front, back,
and sides for proper ventilation and access.
• Install the platform in Information Technology Rooms in accordance with Article 645 of
the National Electrical Code and NFPA 75.
For more information about platform storage and environmental temperatures, see
Specications.
Cabinet placement
Install VEP4600 only in indoor cabinets designed for use in a controlled environment.
Do not install the platform in outside cabinets. For cabinet placement requirements, see Site
selection.
The cabinet must meet minimum size requirements. Airow must be in accordance with the
Electronic Industries Alliance (EIA) standard. Ensure that there is a minimum of 5 inches
(12.7 cm) between the intake and exhaust vents and the cabinet wall.
Rack mounting
When you prepare your equipment rack, ensure that the rack is grounded. Ground the
equipment rack to the same ground point the power service in your area uses. The ground
path must be permanent.
System ground
Dell recommends grounding your system. Use VEP4600 in a CBN.
Fans and airow
Fan installation is done as part of the factory install based on stock keeping unit (SKU) type.
VEP 4600 supports an AC normal fan unit with fan airow from the I/O to the PSU.
8Site preparations
For proper ventilation, position the platform in an equipment rack or cabinet with a minimum
of 5 inches (12.7 cm) of clearance around the exhaust vents. The fan speed varies based on
internal temperature monitoring. The platform never intentionally turns o the fans.
Power
Connect the platform to the applicable power source using the appropriate power cable. An
AC power cable is included with the platform.
When installing AC platforms, follow the requirements of the National Electrical Code ANSI/
NFPA 70, where applicable.
The platform is powered-up when the power cable is connected between the platform and
the power source.
CAUTION: Always disconnect the power cable before you service the power supply
slots. The platform has multiple power cords. Before servicing, ensure that all power
cords are disconnected.
CAUTION: Use the power supply cable as the main disconnect device. Ensure that
the socket-outlet is located/installed near the equipment and is easily accessible.
Storing components
If you do not install the VEP4600 and components immediately, properly store the platform
and all optional components following these guidelines:
• Storage location temperature must remain constant. The storage range is from -40°C to
70°C (-40°F to 158°F).
• Store on a dry surface or oor, away from direct sunlight, heat, and air conditioning
ducts.
• Store in a dust-free environment.
NOTE: ESD damage can occur when components are mishandled. Always wear an
ESD-preventive wrist or heel ground strap when handling the platform and its
accessories. After you remove the original packaging, place the VEP4600 and its
components on an anti-static surface.
Site preparations 9
VEP4600 installation
To install VEP4600, complete the installation procedures in the order presented in this
section.
Always handle the platform and its components with care. Avoid dropping the platform or
any eld replaceable units (FRUs).
NOTE: ESD damage can occur if components are mishandled. Always wear an ESD-
preventive wrist or heel ground strap when handling the platform and its
components. As with all electrical devices of this type, take all the necessary safety
precautions to prevent injury when installing this platform.
Topics:
• Unpack
• Ground cable
• Rack or cabinet installation
• Two-post installation
• Four-post installation
• Optics installation
• Platform power-up
Unpack
NOTE: Before unpacking the platform, inspect the container and immediately report
any evidence of damage.
When unpacking VEP4600, make sure that the following items are included:
• One VEP4600
• One RJ-45 to DB-9 female cable
3
10 VEP4600 installation
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Dell Hardware di rete
Dell
Dell VEP1400 Series Manuale utente
Dell
Dell FS7500 Manuale
Dell
Dell E665 Manuale
Dell
Dell PowerProtect DM5500 Manuale utente
Dell
Dell PowerVault NX1950 Manuale utente
Dell
Dell EMC Virtual Edge Platform 1405 Series Guida utente
Dell
Dell EMC NX430 System Manuale utente
Dell
Dell PowerConnect W-Airwave Manuale utente
Dell
Dell MC SD-WAN Edge 3400 Advanced Manuale utente
Dell
Dell OptiPlex Small Form Factor 7010 Manuale utente
Dell
Dell PowerVault NX3610 Manuale utente
Dell
Dell TrueMobile 2300 Manuale utente
Dell
Dell XC720xd Manuale utente
Dell
Dell PowerVault 110T DLT VS80 Manuale utente
Dell
Dell Safeguard 5242LR Manuale utente
Dell
Dell 53-1002116-01 Manuale di servizio
Dell
Dell PowerConnect W-620 Manuale utente
Dell
Dell VEP4600 Guida utente
Dell
Dell PowerProtect Data Manager Appliance 5.13.0.0 Manuale utente
Dell
Dell 210-APGV Manuale utente
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
